Advantech FWA-3033-00A1R Manual de instalación y operación
1U Rackmount Network Appliance with 10 GbE LAN ports and 2NMC
Slots based on Intel Coffee Lake CPU Xeon® E family and 8th/9th gen.
Intel® Core™ i7/i5/i3 processors
Before installation, ensure that the following materials have been received:
One Internet Security Platform
One box of accessories
One warranty certificate
FWA-3033-00A1R
FWA-3033L-00A1S
Main Board Functions
CPU: Intel® XeonTME-2226GE/ E-2278GE/ E-2124G/ E-2176G, 8/9th Gen Intel® CoreTM Processors I7-8700, I5-8500, I3-8100, I7-9700E,
I5-9500E, I3-9100E, Intel® Pentium® Processor G5400, Intel® Celeron® Processor G4900
Chipset: Intel® C246
Memory: 4 x DDR4 UDIMMs, 2400/2666 MHz, up to 128GB memory capacity
PCI-Express: 2 PCIe x8 Size slots for HL/FL PCIE card, one slot bandwidth is PCIEx4 Gen3, another is PCIEx2 Gen3; 1 Mini-PCIE
reserved on Riser
Network Connectivity:
NMC Modules: 2 NMC slots, with PCIe Gen3 x8 Connectivity
Management: 6-8 LAN ports onboard by 10/100/1000 Base-T Ethernet, 4 SFP ports onboard (SKU option)
Mass Storage: 2 x 3.5" internal SATA HDD/SSD, 1 x M.2 2260/2280 Slot, M-Key
Peripherals:
LCD Module: 16 x 2 graphic display, 5 buttons
Console:1 x RJ45 Console port
USB: 2 x USB3.0 Type A on Front
LAN: 6-8 x Intel i210-AT 10/100/1000 Base-T Ethernet
Power supply: 300W FSP AC and DC redundant, or 250W Delta AC single
Dimensions (W x H x D): 438 x 44 x 550 mm
Weight:15KG
Environment: Operating / Non-operating
Temperature: 0 ~ 40℃/ -40 ~ 60℃
(32 ~ 104°F) / (-40 ~ 140°F)
Humidity: 40°C @ 5 ~ 95% RH Non-Condensing
Startup manual
Part Number List
Specification
FWA-3033 Internet Security Platform
FWA-3033-00A1R Front view
FWA-3033-00A1R Back view
FWA-3033L-00A1S Front view
FWA-3033L-00A1S Back view
Set up
1. To unpack, first remove 9 screws on the side of the machine by referring to the arrows below.
Installation
Installing the CPUs
1. Taking one CPU at a time, remove the protective shield, if present, and press the load lever and move it out till it is clear of the
retention tab, and raise it.
2. Make sure that alignment triangle on the CPU lines up with the correct corner on the socket, and ease the CPU into place.
3. Close the load plate and push the load lever back down until it engages the retention tab.
Installing the heatsink and air scoop
1. Take out Heatsink, Fan cover and 4 screws from the accessory box, and attach the Fan cover and Heatsink lock together according
to the position shown by the arrow in the figure below.
2. Refer to the figure below to attach the four screws diagonally on the Heatsink to the CPU bracket, and then take out three screws
from the accessory box to attach the Fan cover to the chassis (2 silver locks on both sides, 1 black lock in the middle).
Installing the RAM
1. Insert the prepared memory into the DIMM slot, and make sure that the card hook is in place.
Installing the HDD
-The following HDD assembly model can only choose one of them
3.5’HDD Assembly
1. Remove the screw at the position shown by the arrow in the figure below and reserve it, and then remove the HDD bracket.
2. Take out the 4 teeth screws in the accessory box, and refer to the figure below to attach the 3.5 ’HDD to the bracket.
3. After installing the HDD bracket on the base, confirm that the cables at the arrows in the figure below can be pulled.
4. Use the removed 4 screws to lock the HDD bracket, and plug the SATA cable and the Power cable from the power supply to the
HDD.
2.5’HDD Assembly
If this HDD bracket needs to assemble a 2.5 ’HDD, proceed as follows.
1. Take out four yellow anti-vibration pads from the accessory box and install them in the position shown in the figure below.
2. Take out 4 screws from the accessory box and attach the HDD to the bracket with reference to the figure below.
3. Confirm that the wire at the yellow circle in the figure below can be pulled, and then fix the bracket with 4 screws removed.
4. Plug the SATA cable and the power cable from the power supply into the HDD.
Two layers of the 2.5’ HDD installation.
1. Take out and install the HDD bracket and shockproof rubber pad from the accessory box.
2. The SATA port of the HDD is placed towards the bracket without a beveled edge, as shown in the red frame below, and then
attached to the bracket with 8 screws which are taken out of the accessory box.
3. Adjust 4pin cable to the edge of the chassis (the yellow box in the figure below), and then attach the bracket to the base.
4. Connect the SATA cable and the Power cable from the power supply to the HDD.
Install M.2
1. Take out one screw from the accessory box and fix the installed M.2 lock on the silver pillar of the motherboard.
The expansion of the riser card
1. This card has a Mini PCIE and PCIE slots can be used in the extension
Mini-PCIE extension
1. Remove three screws indicated by the arrows in the figure below and pull out the card.
2. Take out the copper pillar lock from the accessory box and attach it to the riser card.
Here you can expand the half card and the full card. The half card needs to be locked with a copper post, and the long card doesn’t
need.
3. Use 1 screw taken from the accessory box to attach the half-size mini-PCIE lock to the riser card.
4. Then use three removed screws to attach the riser lock back to its original position.
PCIE extension
1. Remove 4 screws at the arrow below and remove the blanking module.
2. Remove one of the screws on the blanking module shown by the arrow in the figure below, and remove the blanking plate.
Only one PCIE card is attached here, so you only need to remove one blank.
Ful
3. Insert the expansion card (take NMC card for example) into the bracket as shown in the figure below, and lock it with the removed
screws.
4. Insert the processed network card module into the PCI-E slot, and then use the removed four screws to lock the bracket in the
position shown by the arrow in the figure below.
If you install two expansion cards, you need to confirm whether the pins of the lower expansion card touch the base. If so, you need
to do insulation treatment before installing.
Installing HDD
-If the riser card position need to install the HDD, you need to remove the riser card first
1. Refer to the figure below to remove three screws at the arrow and pull out the card.
2. Remove the copper post from the accessory box and lock it on the base chassis.
3. Take out six anti-vibration washers and HDD brackets from the accessory box, and install them in the positions shown by the arrows
in the figure below.
4. Take out six screws from the accessory box, and attach the 3.5 ’HDD to the bracket with reference to the arrow position in the figure
below.
5. Take out 4 screws from the accessory box and lock the HDD bracket in the chassis.
6. Take out two cables from the accessory box. Refer to the figure below, connect the SATA power cable to the power 4pin connector
pointed by the arrow, and connect the cable along the dotted line to the HDD; One end of the SATA data cable is connected to the
motherboard, and another end connect to the HDD.
7. Attach the Fan cover to the base, and arrange the extra SATA Power cable.
Installing the NMC
1. Remove the NMC blank by turning the screw in the direction of the arrow as shown below.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Hardware de computadora de Advantech
Advantech
Advantech POC-W243 Series Manual de usuario
Advantech
Advantech ITA-2230 Series Manual de instalación y operación
Advantech
Advantech PPC-3151 Manual de usuario
Advantech
Advantech IPC-619 Manual de usuario
Advantech
Advantech ARK-1380 Manual de usuario
Advantech
Advantech PCE-5130 Manual de usuario
Advantech
Advantech PCA-6119P7 Manual de instalación y operación
Advantech
Advantech FWA-3050 Manual de usuario
Advantech
Advantech PCE-5B09-06 Manual de instalación y operación
Advantech
Advantech SOM-5786 Manual de usuario
Advantech
Advantech SOM-6883 Manual de usuario
Advantech
Advantech FWA-3270A Manual de instalación y operación
Advantech
Advantech AIMB-278 Manual de usuario
Advantech
Advantech ROM-8720 Manual de usuario
Advantech
Advantech PCA-6179 Manual de usuario
Advantech
Advantech PCE-7B13-0AA1 Manual de instalación y operación
Advantech
Advantech MIC-75M20 Manual de instalación y operación
Advantech
Advantech PCA-6143P Manual de usuario
Advantech
Advantech SOM-5991 Manual de usuario
Advantech
Advantech PCA-6742 Series Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
