ADTRAN Express 4110 Manual de usuario

Express 4110/4120

ISDN Router/Bridge

USER MANUAL

61200176L3-1A

May 1999

Part Number:

Express 4110/4120 1200176L2/1200176L3

Trademarks:

DMS-100 is a trademark of Northern Telecom, Inc.

Ethernet is a trademark of Digital Equipment Corporation, Intel Corporation, and Xe-

rox Corporation.

ExpertISDN (patent number 5,715,241) is a trademark of ADTRAN, Inc.

Macintosh is a registered trademark of Apple Computer, Inc.

Novell, NetWare, and Internetwork Packet Exchange (IPX) are registered trademarks

of Novell, Inc.

Windows is a registered trademark of Microsoft Corporation.

5ESS is a registered trademark of LUCENT.

The Express 4110/4120 incorporate Synchronous Data Compression based on either

IBM orhi/fn proprietary intellectual property depending on the time ofmanufacture.

The following trademarks and copyrights are applicable:

Stacker LZS Compression

Redistribution and use in source and binary forms are permitted provided that the

above copyright notice and this paragraph are duplicated in all such forms and that

any documentation, advertising materials, and other materials related to such distri-

bution and use acknowledge that the software was developed by Carnegie Mellon

University. The name of the University may not be used to endorse or promote prod-

ucts derived from this software without specific prior written permission. This soft-

ware is provided “as is” and without any express or implied warranties, including,

without limitation, the implied warranties of merchantability and fitness for a partic-

ular purpose.

hi/fn

5993 Avenida Encinas

Carlsbad, CA

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

Printed in USA.

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of the FCC rules. On the bottom of

the equipment housing is a label that shows the FCC registration number

and Ringer Equivalence Number (REN) for this equipment. If requested,

provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone

company may temporarily discontinue service. If possible, advance noti-

fication is given; otherwise, notification is given as soon as possible. The

telephone company will advise the customer of the right to file a com-

plaint with the FCC.

3. The telephone company may make changes in its facilities, equipment, op-

erations, or procedures that could affect the proper operation of this

equipment; advance notification and the opportunity to maintain uninter-

rupted service is given.

4. If experiencing difficulty with this equipment, please contact ADTRAN

for repair and warranty information. The telephone company may re-

quire this equipment to be disconnected from the network until the prob-

lem is corrected or it is certain the equipment is not malfunctioning.

5. This unit contains no user serviceable parts.

6. An FCC compliant telephone cord with a modular plug is provided with

this equipment. In addition, an FCC compliant cable appropriate for the

dial backup option ordered is provided with this equipment. This equip-

ment is designed to be connected to the telephone network or premises

wiring using an FCC compatible modular jack, which is Part 68 compliant.

7. The following information may be required when applying to the local

telephone company for leased line facilities.

To ADTRAN service personnel: For continued protection against risk of fire,replace F1

with the same type and rating of fuse only: .2A, 250 V.

Service Type Digital Facility

Interface Code Service Order

Code Network

Jacks

ISDN 021S5 6.0N RJ-49C

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY

INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential environment. This

equipment generates, uses, and can radiateradio frequency energy and, ifnot installed

and used in accordance with the instructions, may cause harmful interference to radio

or TV reception, which can be determined by turning the equipment off and on. The

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this unit not expressly approved by ADTRAN will void

the user's authority to operate the equipment.

ADTRAN YEAR 2000 (Y2K) READINESS DISCLOSURE

ADTRAN has established a Year 2000 program to ensure that our products and opera-

tions will correctly function in the new millennium. ADTRAN warrants that all prod-

ucts meet Year 2000 specifications regardless of model or revision. Information about

ADTRAN’s Year 2000 compliance program is available at the following:

Web Site www.adtran.com

Product Matrix www.adtran.com/Y2Kfax.html

Faxback Document Line (256) 963-8200

Y2K plans and product certifications

are listed in the matrix

Y2K Project Line (256) 963-2200

E-mail year [email protected]m

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceedthe Class B limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled

"Digital Apparatus," ICES-003 of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux

appareils numeriques de Class B prescrites dans la norme sur le materiel brouilleur:

"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies certified equip-

ment. This certification means that the equipment meets certain telecommunications

network protective, operational, and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, ensure that it is permissible to be connected to the fa-

cilities of the local telecommunications company. The equipment must also be in-

stalled using an acceptable method of connection. In some cases, the company’s inside

wiring associated with a single-line individual service may be extended by means of a

certified connector assembly (telephone extension cord). Compliance with the above

conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian mainte-

nance facility designated by the supplier. Any repairs or alterations made by the user

to this equipment, or equipment malfunctions, may give the telecommunications com-

pany cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines, and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or an electrician, as appropriate.

The LoadNumber (LN) assigned to each terminal device denotes the percentage of the

total load to be connected to a telephone loop which is used by the device, to prevent

overloading. The termination on a loop may consist of any combination of devices

subject only to the requirement that the total of the Load Numbers of all devices does

not exceed 100.

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be fol-

lowed to reduce the risk of fire, electric shock and injury to persons. The precautions

are listed below.

1. Do not use this product near water (for example, near a bath tub, wash

bowl, kitchen sink or laundry tub, in a wet basement or near a swimming

pool).

2. Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the

manual. Do not dispose of batteries in a fire. They may explode. Check local

codes for any special disposal instructions.

SAVE THESE INSTRUCTIONS.

AFFIDAVIT REQUIREMENTS FOR CONNECTION TO DIGITAL SERVICES

• An affidavit is required to be given to the telephone company whenever

digital terminal equipment without encoded analog content and billing

protection is used to transmit digital signals containing encoded analog

contentwhich are intended for eventual conversion intovoicebandanalog

signals and transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or billing

information is being transmitted or that the output of the device meets

Part 68 encoded analog content or billing protection specifications.

• End user/customer will beresponsible to file an affidavit with the local ex-

change carrier when connecting unprotected CPE to a 1.544 Mbps or sub-

rate digital services.

• Until such time as subrate digital terminal equipment is registered for

voice applications, the affidavit requirement for subrate services is

waived.

AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO

1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES

For the work to be performed in the certified territory of _______________

(telco name)

State of ________________

County of ________________

I, _____________________________ (name), _____________________

(business address), ____________________ (telephone number) being

duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equip-

ment to be connected to 1.544 Mbps and/or ________ subrate digital services.

The terminal equipment to be connected complies with Part 68 of the FCC

rules except for the encoded analog content and billing protection specifica-

tions. With respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance,

and adjustment of the digital CPE with respect to analog content and encoded

billing protection information continuously complies with Part 68 of the FCC

Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded ana-

log content or billing information which is intended to be decoded within the

telecommunications network.

( ) The encoded analog content and billing protection is factory set and is not

under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the

establishment, maintenance, and adjustment of the encoded analog content

and billing information has (have) been trained to perform these functions by

successfully having completed one of the following (check appropriate

blocks):

( ) A. A training course provided by the manufacturer/grantee of the equip-

ment used to encode analog signals; or

( ) B. A training course provided by the customer or authorized representa-

tive, using training materials and instructions provided by the manufacturer/

grantee of the equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institu-

tion) recognized by the manufacturer/grantee of the equipment used to en-

code analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/main-

tainer(s) is (are) under the control of a supervisor trained in accordance with

_________ (circle one) above.

I agree to provide _________________ (telco's name) with proper documenta-

tion to demonstrate compliance with the information as provided in the pre-

ceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of ________, 199___

_________________________________

Notary Public

My commission expires:

_________________________________

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de ADTRAN

ADTRAN

ADTRAN NetVanta 4660 Manual

ADTRAN

ADTRAN NetVanta 3130 Manual de usuario

ADTRAN

ADTRAN NetVanta 4300 Series Manual

ADTRAN

ADTRAN NetVanta 3430 Manual de usuario

ADTRAN

ADTRAN NetVanta 340 Manual de usuario

ADTRAN

ADTRAN NetVanta 3448 Manual de usuario

ADTRAN

ADTRAN NetVanta 1535P Manual

ADTRAN

ADTRAN NetVanta 3205 Manual de usuario

ADTRAN

ADTRAN NetVanta 3448 Manual de usuario

ADTRAN

ADTRAN Total Access 5000 Manual de operación

ADTRAN

ADTRAN NetVanta 4305 Manual de usuario

ADTRAN

ADTRAN 1200350L1 Manual de usuario

ADTRAN

ADTRAN Total Access 544R Guía del usuario

ADTRAN

ADTRAN NetVanta 5305 Manual

ADTRAN

ADTRAN Express L1.5 Manual de usuario

ADTRAN

ADTRAN Express L128T S Manual de usuario

ADTRAN

ADTRAN NetVanta 3200 series Manual

ADTRAN

ADTRAN NetVanta 7100 Manual de servicio

ADTRAN

ADTRAN 1200263L1-1.2A Manual de usuario

ADTRAN

ADTRAN NetVanta 3000 Series Manual

ADTRAN

ADTRAN ATLAS 550 Manual de usuario

ADTRAN

ADTRAN Express L768 Manual de usuario

ADTRAN

ADTRAN NetVanta 3000 Series Manual

ADTRAN

ADTRAN NetVanta 1535P Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad