ADJ HEX700 Manual de usuario

User Instructions

7P HEX IP

40107 6 5

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod-

ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or

programming.

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation

of this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

·Reorient or relocate the device.

·Increase the separation between the device and the receiver.

·Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

·Consult the dealer or an experienced radio/TV technician for help.

TABLE OF CONTENTS

Introduction

Features I Warranty Registration I Installation

Safety Precautions

IP Notice

Layout

DMX Set Up

DMX Addressing

DMX Channel Modes

Color Macro Chart

System Menu

Operating Instructions

Primary-Secondary Configuration

Dimmer Mode Chart I Dimmer Curve Chart

Dimensional Drawings

Power Linking I Trouble Shooting I Cleaning

Limited Warranty (USA Only)

Technical Specications

INTRODUCTION

Unpacking: Thank you for purchasing the 7P Hex IP by ADJ Products, LLC. Every 7P Hex IP has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The 7P Hex IP is a DMX intelligent, IP rated LED par fixture. This fixture can be used

in a stand alone mode or connected in a Primary/Secondary configuration. This par has five

operating modes: RGBWA +UV dimmer mode, Static Color mode, Auto Run mode, Color Macro

mode, and DMX control. This product is intended to be used by professionally trained personnel

only and is not suitable for private use.

These instructions contain important safety information regarding the use and maintenance of this

unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

FEATURES

• Multi-Colors

• Five Operating Modes

• Electronic Dimming 0-100%

• DMX-512 protocol

• IP65 Locking 3-Pin XLR Connections In/Out

• Four DMX Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel Mode, and 13 Channel Mode.

• Multiple Unit Power Linking (See page 24)

Included:

1 x IP65 Locking Power Cable

WARRANTY REGISTRATION

INSTALLATION

The 7P Hex IP carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate

your purchase. All returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the out-

side of the return package. A brief description of the problem as well as the R.A. number must also

be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you

must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting

our customer support team on our customer support number. All packages returned to the service

department not displaying a R.A. number on the outside of the package will be returned to the ship-

per.

The unit should be mounted using a mounting clamp (not provided), axing it to the mounting

bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration

and slipping while operating. Always ensure that the structure to which you are attaching the unit is

secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable

that can hold 12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp.

Ensure ALL connections and end caps are properly sealed with a non-conductive dielectric

grease (available at most electrical suppliers) to prevent water ingress/condensation and/or

corrosion.

SAFETY PRECAUTIONS

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to

remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 24

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture does not appear to operate normally or exhibits a marked change in performance.

D. The fixture has fallen and/or subjected to extreme handling.

SAFETY PRECAUTIONS

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!

FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.

WEAR PROPER EYE AND SKIN PROTECTION.

AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.

AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).

DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.

DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH

OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.

INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE

DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE

DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

IP NOTICE

IP65 RATED

An IP rated lighting fixture is one, which is commonly installed in

outdoor environments and has been designed with an enclosure

that effectively water. The International Protection (IP) rating

system is commonly expressed as "IP" (Ingress Protection) followed

by two numbers (i.e. IP65) where the numbers define the degree

of protection. The first digit (Foreign Bodies Protection) indicates

the extent of protection against particles entering the fixture and

the second digit (Water Protection) indicates the extent of

protection against water entering the fixture. An IP65 rated

lighting fixture is one, which has been designed and tested to

protect against the ingress of dust (6) and low-pressure water jets

from any direction (5).

MARINE/COASTAL ENVIRONMENT INSTALLATIONS!

Please note although this fixture is IP rated, the fixture is NOT

suitable for marine and/or coastal environment installations.

Installing this fixture in a marine and/or coastal environment may

cause corrosion and/or excessive wear to the interior and/or

exterior components of the fixture. Damages and/or performance

issues resulting from installation in a marine and/or coastal

environment will void the manufactures warranty and will NOT be

subject to any warranty claims and/or repairs.

OPTIONAL CORROSION-RESISTANT COATING

Optional Corrosion-Resistant Coatings may be available for this

fixture. Please consult your ADJ Products, LLC sales representative

for details.

LAYOUT

LCD Screen

Mode Button

Up Button

Down Button

Enter Button

IP65 Locking Power

Connection In/Out

IP65 Locking 5-Pin

XLR Connector In/Out

DMX SET UP

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a

DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The 7P Hex IP can be controlled via

DMX-512 protocol. The 7P Hex IP has 4 DMX channel modes. The DMX address is set on the rear panel

of the 7P Hex IP. Your unit requires a standard 5-pin XLR connector for data input

and data output. Werecommend Accu-Cable DMX cables. If you are making your own cables,

be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased

at almost all pro lighting stores). Your cables should be made with a male and

female XLR connector on either end of the cable. Also remember that DMX cable

must be daisy chained and cannot be split.

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de ADJ

ADJ

ADJ Dotz Par Manual de usuario

ADJ

ADJ MDF2PSUX156 Guía del usuario

ADJ

ADJ monster beam Manual de usuario

ADJ

ADJ ENCORE BURST UV IP Manual de usuario

ADJ

ADJ ELEMENT QA Manual de usuario

ADJ

ADJ Focus Spot 5Z Manual de usuario

ADJ

ADJ XS 400 Manual de usuario

ADJ

ADJ 18P HEX IP Manual de usuario

ADJ

ADJ Mega GO Par64 PLUS Manual de usuario

ADJ

ADJ StarTec Series Manual de usuario

ADJ

ADJ WOLFMIX WMX1 Manual de usuario

ADJ

ADJ MIRAGE Q6 PAK Manual de usuario

ADJ

ADJ AV6XS Manual de usuario

ADJ

ADJ MOD QA60 Manual de usuario

ADJ

ADJ Mega GO Bar 50 RGBA Manual de usuario

ADJ

ADJ Bubbletron Go Manual de usuario

ADJ

ADJ Vizi BSW 300 Manual de usuario

ADJ

ADJ STARSHIP Manual de usuario

ADJ

ADJ PINSPOT LED QUAD DMX Manual de usuario

ADJ

ADJ MDF2-9SYS Manual de usuario

ADJ

ADJ Encore Profile 1000 WW Manual de usuario

ADJ

ADJ Mega Bar 50 RGB RC Manual de usuario

ADJ

ADJ StarTec Series Manual de usuario

ADJ

ADJ Startec STINGER Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario