ADJ DMX OPERATOR 384 Manual de usuario

User Manual

DMX OPERATOR 384

Table of Contents

General Instruction.................................................................2

Warnings....................................................................................2

Cautions.................................................................................... 3

Features ..................................................................................1

Control and Functions.............................................................4

Front Panel Overview..............................................................4

Rear Panel Overview..............................................................6

Operation Guide......................................................................7

Joystick Set Up...........................................................................7

Scene Operation.......................................................................10

Chase Operation.......................................................................13

Bank copy & Fixture copy..........................................................17

Fade Time Set Up.................................................................... 17

MIDI Set Up & Chart................................................................ 18

ULink Operation.......................................................................19

USB MEM Stick Data Send.........................................................21

MIDI Control............................................................................25

Technical Specifications .......................................................26

- 384 total DMX channels

- Individual Speed & Fade Time faders

- 30 memory banks x 8 programmable scenes per bank

- 12 programmable chases, 240 steps per chase

- Assignable fade setting

- Manual control chase override

- Built-in microphone or line level input for audio triggering

- MIDI controllable

- Optional foot controller for chase step activation

- Onboard fog machine trigger button

- 7-segment LED display

- Ships with standard joystick module- optional jog wheel module

available

Joystick module Jog wheel module

DMX Operator 384 is a multifunction controller, which works as a DMX

controller and as a simple MIDI controller. When operating as a stage

controller, this unit features;

When operating as a MIDI controller, this unit features;

- Selectable channel 1-16

- MIDI Note

- Control change

- Program change

Features

DMX OPERATOR 384

- 8 channel faders x 4 channel banks

- 12 fixtures x 32 channels each

DMX OPERATOR 384

General Introduction

Every effort has been made to design dependable, reliable and user friendly

products. New products are being designed constantly to meet the needs

of both entertainment and special effects lighting industries. We welcome your

comments about our product and services and are open to suggestions on

how we can improve to better serve you.

It is a privilege for us to be chosen as your control solution.

This controller is an expansion of the simple to use DMX OPERATOR 192. We

have added two channel banks, which now give you control of up to 32 channels

per fixture. A joystick is supplied for traditional X/Y control of a moving light.

We also offer optional data wheels,if you prefer to use them for control.

To optimize performance of this product, please read the instructions carefully

to familiarize yourself with the basic functions and operations.

Warnings

This unit is intended for indoor use only.

Do not allow for any flammable liquids, water or metal objects to enter the

unit.

No user serviceable parts inside, do not dismantle the unit yourself.

Please do not allow children to play and tamper with this product.

To reduce the risk of fire or electric shock, do not expose the unit to rain or

high levels of moisture.

Repairs must be done by qualied personnel only.

Specifications and improvements in the design of this product and this

manual are subject to change without any prior notice.

Notice:

Cautions

When unpacking, please ensure that the unit is not damaged. Should

something be wrong, please contact us immediately.

transcribed or translated into any language, in any form, by any means,

without authorized permission from Botex.

DMX OPERATOR 384

8. Joystick/Jog wheel:

Traditionally used to adjust the X/Y channels of a moving light.

6. FINE button:

Used in conjunction with the joystick or data wheels. When the FINE button is

engaged, adjusting the joystick or data wheels will be more precise when needing

to hit a specific area with a scanner or moving head.

7. MODE button:

This is a multi-function button that is used when assigning the joystick & Fade

setting.

Control and Functions

Front Panel Overview

4. Speed fader:

Used to adjust chase speed (range is 0.1 second to 10 minutes per step).

1. Fixture buttons(1~12):

Used to select relevant fixtures for control.

5. Fade Time fader:

Used to adjust chase fade time (range is 0 to 30 seconds).

3. Channel Bank button:

Used to switch between channels 1-8, 9-16, 17~24 and 25~32.

2. Channel faders(1~8):

Used to control the output of each corresponding fixture channel.

DMX OPERATOR 384

23456

910 11

14~19

9. Scene buttons (1-8):

Used when storing or playing back programmed scenes. Also used when backing

up data to a USB MEM Stick or through a ULink Cable.

10. LED-display:

The LED-display shows you relevant information depending on current operation.

11. Bank Up/Down button:

Used to select a scene bank or chase step.Also used to view files in memory stick.

19. Black-out button:

Used to bring all current output down to zero.

15. Music/Bkc button:

Used to engage audio mode for chase synchronization and to copy a bank of

scenes to another.

16. Midi/Rec button:

Used to record scenes and chase steps. Also used to setup Midi operation.

14. Program button :

Used to enter and exit Record mode when programming.

18. Tap/Disp button:

Used to tap sync chase playback and to change display view operation.

17. Auto/Del button :

Used to enter AUTO mode for automatic scene bank sequence or to delete a

scene or chase.

12. Fog-machine button:

Used to trigger fog machine which should be connected to rear of console.

13. Chase buttons (1-12):

Used when storing or playing back relevant chases.

DMX OPERATOR 384

Rear Panel Overview

4. MIDI IN:

to receive MIDI information from a midi sequencer or compatible device.

6. 3 Pin Female XLR:

DMX output. Connect to first device in line.

2. Audio input:

to connect line level input for audio trigger (0.1V-1Vp-p).

7. DC INPUT:

connects the included power supply to this input. (DC 9V~15V, 500mA Min).

3. DB-9 connector:

to connect optional external chase step controller.

1. Label:

lists model, serial number and production date.

8. Power switch:

used to switch the units power on and off.

5. Fog machine connector:

to connect a compatible fog machine.

9. USB Interface:

outputs the MIDI signal via USB interface when connected to MIDI controller.

10. LED Lamp:

indicates the working state of USB interface.

11. Switch:

switches the function of DMX controller or MIDI controller. The change will work

after re-startup.

12. MIDI Out Socket:

output the MIDI signal when connected to the MIDI controller.

DMX OPERATOR 384

Midi In

Midi Out

1=NC; 2=GND

3=NC; 4=V+

5=Signal

1=NC; 2=NC

3=NC; 4=V+

5=Signal

Made in PRC

DC input:

9V-12VDC, 500mA Min

125

910 11 12

Midi In

Midi Out

1=NC; 2=GND

3=NC; 4=V+

5=Signal

1=NC; 2=GND

3=NC; 4=V+

5=Signal

1=NC; 2=NC

3=NC; 4=V+

5=Signal

1=NC; 2=NC

3=NC; 4=V+

5=Signal

Made in P.R.C.

Power

RoHS

DC In

DC input:

9V-12VDC, 500mA Min

DMX Out

FOG MachineMidi In Midi Out

DB-9

EXT Step Control

Audio

Line Input 0.1V-1Vp-p

USB

Serial Number:

1 = Ground

2 = Data -

3 = Data +

1 = Ground

2 = Data -

3 = Data +

DMX Out

DMX

Midi

Joystick Set Up

"Assign Joystick"

(2) Press and hold down the MODE button and then tap the FINE button. The "Assign"

and "Pan" LED's should illuminate.

(3)

Operation Guide

(1) Press and hold down the Program button for approximately 2 seconds or until the

PROG indicator in the LED-display flashes. Once the indicator is flashing, record

mode is engaged and you may release the Program button.

Select the fixtures that you wish to assign the "Pan" for by pressing the FIXTURES

# buttons, 1-12, so the selected fixture LED's illuminate.

(4) Press the Tap/Disp button to switch between "PL.XX" & "PH.XX". "PL.XX"

represents the Low Byte or Fine channel, generally listed as the Pan Fine channel

and PH.XX represents the High Byte or Coarse channel, generally listed as the

Pan channel. Set it to "PH.XX" and press and hold down the MODE button and

then tap the SCENE button that corresponds to the Pan channel of your fixture.

For example, if your fixtures Pan channel is 1 then you'd press the SCENE #1

button . Please refer to the fixtures DMX chart. If your fixture includes a pan fine

channel, press the Tap/Disp button so the display reads "PL.XX". Press and hold

down the MODE button and then tap the SCENE button that corresponds to the

Pan Fine channel of your fixture. For example, if your fixtures Pan Fine channel is

2 then you'd press the SCENE #2 button.

(5) Press the BANK UP or DOWN buttons to switch between "TL.XX" & "TH.XX".

"TL.XX" represents the Low Byte or Fine channel, generally listed as the Tilt Fine

channel and TH.XX represents the High Byte or Coarse channel, generally listed

as the Tilt channel. Set it to "TH.XX" and press and hold down the MODE button

and then tap the SCENE button that corresponds to the Tilt channel of your

fixture. For example, if your fixtures Tilt channel is 3 then you'd press the SCENE

#3 button. Please refer to the fixtures DMX chart. If your fixture includes a Tilt

Fine channel,press the Tap/Disp button so the display reads "TL.XX". Press and

hold down the MODE button and then tap the SCENE button that corresponds to

the Tilt Fine channel of your fixture. For example, if your fixtures Pan Fine channel

is 2 then you'd press the SCENE #4 button.

(6) Press and hold down the Program button for approximately 2 seconds or until the

PROG indicator in the LED-display stops flashing. A flashing Blackout indicator in

the LED-display confirms that the controller is out of Program mode.

DMX OPERATOR 384

(1) Press and hold down the Program button for approximately 2 seconds or until the

PROG indicator in the LED-display ashes. Once the indicator is ashing, record

mode is engaged and you may release the Program button.

(2) Press and hold down the MODE button and then tap the FINE button. The "Assign"

and "Pan" LED's should illuminate.

(3)

Select the xtures that you wish to assign the "Pan Reverse" & "Tilt Reverse" for

by pressing the FIXTURES # buttons, 1-12, so the selected xture LED's

illuminate. Ideally, you should assign opposite xtures for Pan/Tilt Reverse. For

example, xtures 1, 3, 5, 7, etc... should be assigned normal as described in the

previous section and xtures 2, 4, 6, etc..., should be assigned reversed so that

when moving the joystick around, xtures movements are reversed from one

another. This feature is traditionally referred to as Pan/Tilt invert.

(5) Press the Tap/Disp button to switch between "PL.XX" & "PH.XX". "PL.XX"

represents the Low Byte or Fine channel, generally listed as the Pan Fine channel

and PH.XX represents the High Byte or Coarse channel, generally listed as the Pan

channel. Set it to "PH.XX" and press and hold down the MODE button and then tap

the SCENE button that corresponds to the Pan channel of your xture.For example,

if your xtures Pan channel is 1 then you'd press the SCENE #1 button. Please

refer to the xtures DMX chart. If your xture includes a pan ne channel, press the

Tap/Disp button so the display reads "PL.XX". Press and hold down the MODE

button and then tap the SCENE button that corresponds to the Pan Fine channel

of your xture. For example, if your xtures Pan Fine channel is 2 then you'd press

the SCENE #2 button.

(6) Press the BANK UP or DOWN buttons to switch between "TL.XX" & "TH.XX".

"TL.XX" represents the Low Byte or Fine channel, generally listed as the Tilt Fine

channel and TH.XX represents the High Byte or Coarse channel, generally listed as

the Tilt channel. Set it to "TH.XX" and press and hold down the MODE button and

then tap the SCENE button that corresponds to the Tilt channel of your xture. For

example, if your xtures Tilt channel is 3 then you'd press the SCENE #3 button.

Please refer to the xtures DMX chart. If your xture includes a Tilt Fine channel,

press the Tap/Disp button so the display reads "TL.XX". Press and hold down the

MODE button and then tap the SCENE button that corresponds to the Tilt Fine

channel of your xture. For example, if your xtures Pan Fine channel is 2 then

you'd press the SCENE #4 button.

(7) Press and hold down the Program button for approximately 2 seconds or until the

PROG indicator in the LED-display stops ashing. Aashing Blackout indicator in

the LED-display conrms that the controller is out of Program mode.

(4)

Once again, press and hold down the MODE button and then tap the FINE button.

The "Reverse" LED should illuminate.

DMX OPERATOR 384

"Assign Joystick Reverse" (Pan/Tilt Invert)

Otros manuales para DMX OPERATOR 384

Tabla de contenidos

Otros manuales de Equipo de DJ de ADJ

ADJ

ADJ PAR Z120 RGBW Manual de usuario

ADJ

ADJ M-101HD Manual de usuario

ADJ

ADJ 7PZ IP Manual de usuario

ADJ

ADJ American DJ FUSION FX BAR 1 Manual de usuario

ADJ

ADJ THEATRIX PRO 48 LED Manual de usuario

ADJ

ADJ Eliminator Lighting FROST FX BAR W Manual de usuario

ADJ

ADJ 32 HEX PANEL IP Manual de usuario

ADJ

ADJ VIZI BEAM 5RX Manual de usuario

ADJ

ADJ MDF2PSUX156 Guía del usuario

ADJ

ADJ HYDRO WASH X7 Manual de usuario

ADJ

ADJ MOD TW100 Manual de usuario

ADJ

ADJ MEGA HEX PAR Manual de usuario

ADJ

ADJ Vizi Q Wash7 Manual de usuario

ADJ

ADJ SCENE SETTER 48 Manual de usuario

ADJ

ADJ MOD QA60 Manual de usuario

ADJ

ADJ ENCORE LP7P Manual de usuario

ADJ

ADJ ENCORE BURST RGBW IP Manual de usuario

ADJ

ADJ Encore Profile 1000 WW Manual de usuario

ADJ

ADJ ENTOUR ICE Manual de usuario

ADJ

ADJ ECO UV BAR 50 IR Manual de usuario

ADJ

ADJ BUBBLETRON Manual de usuario

ADJ

ADJ ENCORE FR50Z Manual de usuario

ADJ

ADJ Par Z Move RGBW Manual de usuario

ADJ

ADJ ENCORE PROFILE PRO WW Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario