ADJ Startec RAYZER Manual de usuario

User Instructions

RAYZER

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

Date Document

Version

Software

Version

DMX

Channel

Mode

Notes

DOCUMENT VERSION

Please check www.adj.com for the latest revision/update of this guide.

11/19/18 1 3 5/8/29 Initial Release

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 2

Rayzer Table of Contents

Introduction

Features I Warranty I Installation

Safety Precautions

Laser Warnings

DMX Setup

DMX Addressing

Overview

System Menu

Operating Instructions

Oset Menu

Master-Slave Setup

ADJ UC IR/Airstream IR Control

DMX Modes

Dimensional Drawings

Fuse Replacement I Trouble Shooting I Cleaning

Warranty

Technical Specications

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 3

Rayzer Introduction

Unpacking: Thank you for purchasing the Rayzer by ADJ Products, LLC. Every Rayzer has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The ADJ Rayzer is a DMX intelligent LED fixture. The Rayzer can operate as a stand

alone fixture or in a Master/Slave set up. The Rayzer has three operating modes; show mode, sound

active mode, & DMX controlled. This fixture is suitable for theaters, studios, retail stores, and other

similar locations. For best results use fog or special effects smoke to enhance the beams projections.

These instructions contain important safety information regarding the use and maintenance of this

system. Please keep this manual with the system, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-832-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

WARNING!

To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or moisture.

CAUTION!

There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will

void your manufactures warranty. In the unlikely event your unit may require service please contact

ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Rayzer Features

• Three Operating Modes

• Electronic Dimming 0-100%

• DMX-512 Protocol | 3pin DMX In/Out Connections

• Three DMX Modes: 5 / 8 / 29

• ADJ UC IR compatible (Not Included) and Airstream IR compatible (Transmitter Not Included)

Rayzer Warranty Registration

Rayzer Installation

The Rayzer carries a 2 year (730 Days) limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under war-

ranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by

contacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

Fixtures should be mounted using a mounting clamp (not provided), axing it to the mounting

bracket that is provided with the unit. Always ensure that the xture is rmly xed to avoid vibration

and slipping while operating. Always ensure that the structure to which you are attaching the unit is

secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable

that can hold 12 times the weight of the unit when installing the xture. The equipment must be

installed by a professional, and it must be installed in a place where it is out of the reach of people’s

grasp.

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 4

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 5

Rayzer Safety Precautions

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before

You Attempt To Install Or Operate This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required voltage for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used

to reduce the risk of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 24

for cleaning details.

• Heat -This fixture should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 6

Rayzer Laser Warnings

US Version

Wavelength:532nm, 450nm,

650nm

Wavelength:532nm, 450nm,

650nm

S pe cs La be l

S pe cs L a be l

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 7

Rayzer Laser Warnings

EU Version

S pe cs La be l

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 8

Rayzer DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA

“IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Rayzer can be

controlled via DMX-512 protocol and has 3 DMX channel modes. The DMX address

is set on the back panel. The Rayzer require standard 3-pin XLR connectors for data

input and data output (Figure 1), which are included on the included DMX cables.

If you are making your own cables, be sure to use standard 110-120 Ohm shielded

cable (This cable may be purchased at almost all pro lighting stores). Your cables

should be made with a male and female XLR connector on either end of the cable.

Also remember that DMX cable must be daisy chained and cannot be split. Figure 1

Notice: Be sure to follow gures 2 and 3 below when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a

short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

ADJ Products, LLC - www.adj.com - Rayzer User Manual Page 9

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a

terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor

which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is

inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a

cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

Rayzer DMX Set Up

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5pin DMX-512 data cables for DATA

transmission in place of 3pin. 5pin DMX xtures may be implemented in a 3-pin DMX line. When

inserting standard 5pin data cable in to a 3pin line a cable adaptor must be used, these adaptors are

readily available at most electric stores. The chart below details a proper cable conversion.

Conductor 5pin XLR Male (In)3pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de ADJ

ADJ

ADJ WiFly NE1 Manual de usuario

ADJ

ADJ VIZI CMY 16RX Manual de usuario

ADJ

ADJ FLAT PAR QWH5XS Manual de usuario

ADJ

ADJ HYDRO WASH X7 Manual de usuario

ADJ

ADJ WOLFMIX WMX1 Manual de usuario

ADJ

ADJ BUBBLETRON Manual de usuario

ADJ

ADJ Vizi Beam Hybrid 2R Manual de usuario

ADJ

ADJ PinPoint Gobo COLOR Manual de usuario

ADJ

ADJ M-1212 Manual de usuario

ADJ

ADJ Inno Pocket Spot Pearl Manual de usuario

ADJ

ADJ PinPoint Gobo COLOR Manual de usuario

ADJ

ADJ ENCORE BURST RGBW IP Manual de usuario

ADJ

ADJ Mega Bar RGBA Manual de usuario

ADJ

ADJ AV6XS Manual de usuario

ADJ

ADJ VIZI BEAM 5RX Manual de usuario

ADJ

ADJ 6-PACK SKB CASE Manual de usuario

ADJ

ADJ Dotz Par Manual de usuario

ADJ

ADJ DOTZ MATRIX Manual de usuario

ADJ

ADJ ECO UV BAR PLUS IR Manual de usuario

ADJ

ADJ BLACK-24BLB Manual de usuario

ADJ

ADJ ENCORE PROFILE PRO WW Manual de usuario

ADJ

ADJ MOD QW100 Manual de usuario

ADJ

ADJ POCKET PRO Manual de usuario

ADJ

ADJ XPress LED Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario