Adam Equipment DCT 201 Manual de usuario

Adam Equipment

DUNE DCT SERIES

(P.N. 9384, Revision B2, June 2013

Easy Referen e:

Model name of the scale:

Serial number of the unit:

Software revision number

(Displayed when power is first turned on :

Date of Purchase:

Name of the supplier and place:

| Page © Adam Equipment Company 2013

1.0 CONTENTS

1.0

CONTENTS...........................................................................................1

2.0

INTRODUCTION...................................................................................1

3.0

SET UP .................................................................................................2

3.1

UNPACKING AND SETTING UP YOUR SCALE................................2

3.2

LOCATING AND PROTECTING YOUR SCALE.................................2

3.2

LOCATING AND PROTECTING YOUR SCALE.................................3

4.0

BASIC OPERATION..............................................................................4

4.1

TURNING ON THE SCALE................................................................4

4.2

ZEROING / TARE...............................................................................4

4.3

WEIGHING.........................................................................................4

5.0

FUNCTIONS .........................................................................................5

5.1

AUTO POWER OFF...........................................................................5

6.0

CALIBRATION.......................................................................................5

7.0

TROUBLE SHOOTING..........................................................................6

7.1 ERROR MESSAGES.............................................................................6

7.2

REPLACEMENT PARTS AND ACCESSORIES.................................6

8.0

SPECIFICATIONS.................................................................................7

9.0

WARRANTY INFORMATION................................................................8

2.0 INTRODUCTION

Thank you for purchasing the Dune

, DCT compact scales, Every Dune is equipped

with the features you really need: AC adapter, auto-calibration through the keypad,

low-battery indicator, and overload indicator. With its alternate battery operation,

splash-proof key pad, and sturdy plastic construction throughout, the Dune will

deliver accurate readings both indoors and out.

| Page © Adam Equipment Company 2013

3.0 SET

3.1 UNPACKING

AND

SETTING

YOUR

SCALE

1 Remove the top pan, scale and adaptor from the packaging. Take care not to

apply pressure to the top of the scale.

2 Connect the power adapter to the socket on the back of the machine.

Installing Batteries:

Remove the battery compartment cover and

insert six batteries (R6P/LR6 /AA size) into

the battery compartment taking extreme care

that the polarities plus and minus are

observed.

| Page © Adam Equipment Company 2013

3.2 LOCATING

AND

PROTECTING

YOUR

SCALE

In order to keep you scale functioning at its best we suggest that you do the

following:

Avoid extremes of temperature. Do not place in

direct sunlight or near air conditioning vents.

Make sure the scale is located on a strong table and

free from vibration.

Avoid unstable power sources. Do not use near large

users of electricity such as welding equipment or

large motors. Do not mix batteries and use only the

factory approved power adapter supplied with the

machine. Do not use batteries and the AC adapter at

the same time.

Keep free from vibration. Do not place near heavy or

vibrating machinery.

Avoid high humidity that might cause condensation.

Keep away from direct contact with water. Do not

spray or immerse the scales in water.

Do not place near open windows, air-conditioning

vents or fans that may cause a draft and unstable

readings.

Keep the scales clean. Do not stack material on the

scale / balance when it is not in use.

| Page © Adam Equipment Company 2013

4.0 BASIC

OPERATION

4.1 TURNING

THE

SCALE

Plug in the unit using the AC adapter or use batteries. Do not use battery power and

the AC adapter at the same time.

1 To turn on press the [on/off] key once and release. All of the segments on

the display will light up, then the display shows zero >0<

2 The scale is ready to be used.

3 To turn the scale off after use press the [on/off] key again. There is an auto

power-off function that will automatically turn the unit off after 4 min of

inactivity or no change in the weight reading.

4.2 ZEROING

TARE

You can press the [Tare] key to set a new zero point and show the zero reading if

the weight reading is less than 4% of the total of the maximum capacity of the scale.

This may be necessary if the weight is not reading zero with nothing on the

platform. The zero indicators will light up: >0<.

If you are using a container to weigh then you can place this on the platform and

press the [Tare] key, providing the container weight is more than 4% of the

maximum capacity of the scale, the display will show zero and tare indicator will

light up. You can then weigh your object in the container. Taring weight subtracts

from the total scale capacity.

Note: When the container is removed a negative value will be shown. If the scale

was tared just before removing the container, this value is the gross weight of the

container plus all products which were removed.

4.3 WEIGHING

To determine the weight of a sample, first tare an empty container (if used , then

place the sample in the container. The display will show the weight and the unit of

weight currently in use.

| Page © Adam Equipment Company 2013

5.0 FUNCTIONS

5.1 AUTO

POWER

OFF

The auto power off helps conserve power when using on battery or the AC adapter,

the machine will automatically turn off after 4 min of inactive use or no change in

the displayed weight.

6.0 CALIBRATION

Before calibrating the Dune series it is best to turn on the unit for about 1 min to let

the components warm up.

1 Press [on/off] key to turn the power on, if it is not already.

2 Press and hold the [Unit] key, until “CAL” is displayed

3 Remove any weight from the pan.

4 Press the [Unit] key, the display will flash “CAL” them will show the cal mass

required. If the cal mass is not displayed then the machine is not stable or is

not within a zero range. Turn off the unit and try zeroing the display before

trying another calibration.

5 Place the appropriate calibration mass on the scale:

Model Calibration Mass

DCT 201 200g

DCT 2000 2000g

DCT 5000 5000g

6 After the stable reading the display will show “PASS” then revert to the

weighing mode. If the calibration does not pass the display will show “FAIL”

and shut off.

7 The calibration is now finished. If the calibration is correct, the display will

show the weight value.

NOTE: If the calibration fails retry, if it still fails then there may be damage to the

mechanics or an issue with the power. If you do not follow the procedures in a

timely manner the machine will automatically switch off and the calibration will

not be accepted.

| Page © Adam Equipment Company 2013

7.0 TROUBLE

SHOOTING

7.1

ERROR

MESSAGES

If an error message is shown, repeat the step that caused the message. If the error

message is still shown then contact your dealer for support.

ERROR

CODE

DESCRIPTION POSSIBLE CAUSES

O-Ld Overload Remove weight from the pan. Make

sure the machine is reading zero

before weighing. Do not over load

the pan. If the problem recurs

calibrate. Possible damage to the

internal weighing cell.

OUt2

Out of Zero reading Make sure the pan is fitted correctly.

Make sure nothing is touching the

pan when turning on the unit.

Calibrate the machine. Possible

damage to the internal weighing cell.

UnSt Unstable Make sure the balance is on a flat

surface and away from vibration.

Possible damage to the internal

weighing cell.

LO or

Low Battery indicator Change the batteries or use on the

power adapter.

ErrE E-Prom error Software error turn off and restart.

Contact Adam Equipment or your

dealer for further assistance.

No Power when turning on Change the batteries or use on the

power adapter.

7.2 REPLACEMENT

PARTS

AND

ACCESSORIES

If you need to order any spare parts and accessories, contact your supplier or Adam

Equipment. A partial list of the more common items follows:

Part Number

Description

9402 AC adapter

(Country Dependent

9401 Plastic pan

| Page © Adam Equipment Company 2013

8.0 SPECIFICATIONS

Model Number DCT-201 DCT-2000 DCT-5000

Maximum Capacity 200g 2000g 5000g

Readability 0.1g 1g 2g

Repeatability (Std Dev

0.1g 1g 2g

Linearity ± 0.2g 2g 4g

Units of Measure g / lb /oz g / lb /oz

Stabilisation Time 2 seconds

Operating

Temperature -10ºC to 40ºC

14ºF to 104ºF

Power Supply 12VAC @ 150mA adapter or 6x AA batteries

Calibration Push button calibration using external mass

Calibration Mass 200g 2000g 5000g

Display 5 digit LCD display 15mm high

Balance Housing ABS Plastic

Pan Size 145 x 145mm

5.8” x 5.8”

Overall Dimensions

(w x d x h

145 x 210 x 40mm

5.8" x 8.3" x 1.6"

Gross Weight 1kg, 2.2lb

Features Low battery, Stable and Zero indications

| Page © Adam Equipment Company 2013

9.0 WARRANTY INFORMATION

Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to

defects in materials or workmanship. Warranty starts from the date of delivery.

During the warranty period, should any repairs be necessary, the purchaser must inform its

supplier or Adam Equipment Company. The company or its authorised Technician reserves the

right to repair or replace the components at any of its workshops depending on the severity of

the problems. However, any freight involved in sending the faulty units or parts to the service

centre should be borne by the purchaser.

The warranty will cease to operate if the equipment is not returned in the original packaging

and with correct documentation for a claim to be processed. All claims are at the sole discretion

of Adam Equipment.

This warranty does not cover equipment where defects or poor performance is due to misuse,

accidental damage, exposure to radioactive or corrosive materials, negligence, faulty

installation, unauthorised modifications or attempted repair or failure to observe the

requirements and recommendations as given in this User Manual. Additionally rechargeable

batteries (where supplied) are not covered under warranty.

Repairs carried out under the warranty does not extend the warranty period. Components

removed during the warranty repairs become the company property.

The statutory right of the purchaser is not affected by this warranty. The terms of this warranty

is governed by the UK law. For complete details on Warranty Information, see the terms and

conditions of sale available on our web-site.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Adam Equipment

Adam Equipment

Adam Equipment BCT Series Manual de usuario

Adam Equipment

Adam Equipment NETS Hoja de información del producto

Adam Equipment

Adam Equipment HIGHLAND HCB123 Manual de usuario

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment Warrior Series Manual de usuario

Adam Equipment

Adam Equipment Nimbus NBL Series Manual de usuario

Adam Equipment

Adam Equipment HCB 1002 Manual de usuario

Adam Equipment

Adam Equipment QBW Series Manual de usuario

Adam Equipment

Adam Equipment WBZ 3 Manual de usuario

Adam Equipment

Adam Equipment CORE SERIES Manual de usuario

Adam Equipment

Adam Equipment AQ Series Manual de usuario

Adam Equipment

Adam Equipment CQT 202 Instrucciones de montaje

Adam Equipment

Adam Equipment CCSA series Manual de usuario

Adam Equipment

Adam Equipment Cruiser CKT Series Manual de usuario

Adam Equipment

Adam Equipment ACB-600H Manual de usuario

Adam Equipment

Adam Equipment SHS Series Manual de usuario

Adam Equipment

Adam Equipment CFC SERIES Manual de usuario

Adam Equipment

Adam Equipment MUW 300L Manual de usuario

Adam Equipment

Adam Equipment AZextra 3 Manual de usuario

Adam Equipment

Adam Equipment CORE SERIES Manual de usuario

Adam Equipment

Adam Equipment PGL SERIES Manual de usuario

Adam Equipment

Adam Equipment CBD 100a Manual de usuario

Adam Equipment

Adam Equipment UG119 Manual de usuario

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario