ACTi Q960 Manual de usuario

People Counting Camera

Installation Guide

Q960, Q961, Q962

2019/08/02

www.acti.com

INSTALLATION GUIDE

The following documentation covers the installation and configuration of your

device.

NOTE: The accuracy of the analytics algorithm may be affected by different

environmental factors or inappropriate installation. Please follow the

procedures in this installation guide. ACTi will not be held liable for

inaccuracies resulting from the aforesaid causes.

Part 1: Installation Specification

Model and counting width

The counting width depends on the installation height. The recommended

installation height for dual-lens camera is less than 4.0m (13.1ft). The specific

corresponding relation shown below:

Model

Installation

height

（m/ft）

Max. counting

width

（m/ft）

Without

doorframe

With doorframe

Q960

2.5/8.2

1.8/5.9

Placed in the middle

0.68m(2.2ft)

to door

Placed in the middle

3.0/9.8

2.9/9.5

Placed in the middle

1.1m(3.6ft)

to door

Placed in the middle

3.5/11.5

4.0/13.1

Placed in the middle

1.52m(5.0ft)

to door

Placed in the middle

Q961

3.0/9.8

2.2/7.2

Placed in the middle

0.85m(2.8ft)

to door

Placed in the middle

3.5/11.5

3.1/10.2

Placed in the middle

1.17m(3.8ft)

to door

Placed in the middle

4.0/13.1

Placed in the middle

1.5m(4.9ft)

to door

Placed in the middle

Q962

4.0/13.1

2.8/9.2

Placed in the middle

1.05m(3.4ft)

to door

Placed in the middle

4.5/14.8

3.4/11.2

Placed in the middle

1.28m(4.2ft)

to door

Placed in the middle

5.0/16.4

4.0/13.1

Placed in the middle

1.5m(4.9ft)

to door

Placed in the middle

www.acti.com

INSTALLATION GUIDE

Package Contents

Camera

Mounting Base

Quick Start Guide

Screw Kit

Quick Start

Guide

www.acti.com

INSTALLATION GUIDE

Part 2: Installation Steps

1. Installation

Please pay great attention to the mounting position. Inappropriate mounting

position may cause loss of accuracy. The recommended mounting position is

shown below:

Horizontal sketch map of mounting position

Effect picture after installation

Notice: Avoid the reflective environment (ex: Marble floor)

Vertical sketch map of mounting position

www.acti.com

INSTALLATION GUIDE

Make sure the camera is mounted vertically above the passenger flow

(90°vertical by the ground), see picture below:

Passenger flow

（

perpendicular to the door

）

For some scenarios where there are multiple cameras, mount the cameras

according to two rules.

Rule one: If there are turnstiles, each camera should be mounted to monitor

certain turnstile

www.acti.com

INSTALLATION GUIDE

Rule two:If there is no turnstile, at first, mount the cameras in one line, and

make sure the cameras have the same focal length. Then, keep a proper

distance between each camera according to the overlap (see the yellow

area below) of the adjacent two cameras’ counting width. The suggested

overlapping length is between 0.2-0.5m.

Sketch map of multiple cameras installation

Notice

1) People flow should be in vertical up-and-down direction

Passenger flow in horizontal direction (wrong)

www.acti.com

INSTALLATION GUIDE

Passenger flow in slant direction (wrong)

Passenger flow in vertical up-and-down direction (right)

2) Passageway width should be within camera’s counting width

3) Avoid obstacles such glass door, shield door and turnstile that block the

camera. For Each divided passageway, mount one camera right above.

www.acti.com

INSTALLATION GUIDE

4) The camera should be mounted as close as possible to the passageway

without obstacle. Remove the obstacle or adjust the camera mounting position if

there is obstacle below the camera. Meanwhile, to prevent miscounting, if there’s

a sliding door onsite, make sure the trajectory of the sliding door does not

overlap the detection line. Otherwise, the counting number may be misled by the

door opening and closing

Too far away from the door / Obstacle below camera

Recommended installation

www.acti.com

INSTALLATION GUIDE

Configuration for single camera

Step 1: Enable People Counting: check [Configuration]-[People Counting]

-[Enable People Counting]

Step 2: Calibration- Select the green box, drag it to proper location and click

[Calibration]. After this, “Height” in the configuration page will refresh (close

to the real height). A red box, which means the counting scope, and yellow

detection line will turn up. The arrow shows the direction of entering. See

picture below:

Notice

If auto calibration fails, switch to [Manual] and input the measured “Height”,

then click [Calibration].

Step 3: Detection line: move the detection line to proper location, about 0.5m

to the door. Then adjust the length of detection line to the real door’s width by

dragging the detection line’s two ends. See picture below:

Notice:

You should make the whole detection line in the same ground level or it may

lose accuracy.

www.acti.com

INSTALLATION GUIDE

Step 4: Save configuration and test. After configuration, click [save] and test.

If miscounting happens, slightly adjust the detection line’s location and

length.

3. Configuration for multiple cameras

Step 1: Do configuration for each camera following the steps above

Step 2: Move each camera’s detection line and connect the ends of adjacent

lines. Some objects could be placed on the image border for reference. See

picture below:

Configuration of each detection line

Otros manuales para Q960

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de ACTi

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario