ACTi ACM-7411 Series Manual de usuario

Otros manuales para ACM-7411 Series

4

Este manual sirve para los siguientes modelos

6

Tabla de contenidos

Otros manuales de Cámara de seguridad de ACTi

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

www.acti.com

ACTi

Knowledge Base

Category: Installation & Configuration Note

Sub-category: Integration, Hardware

Model: All 4-inch and 5-inch outdoor domes

Firmware: N/A

Software: N/A

Author: Ando.Meritee

Published: 2011/09/07

Reviewed: 2011/09/07

1

Waterproof Installation of Dome Cameras

Contents

Introduction

Installation of Conduit

Installation in Humid Environment

Introduction

ACTi outdoor dome cameras are all waterproof, rated as IP66. However, this waterproof

condition is guaranteed only if both camera and the cables are properly sealed off. It is

necessary to use waterproof flex conduit to protect the Ethernet cable that connects the

camera from its outdoor installation spot to the indoors or to the nearest waterproof junction

box. The flex conduit can be mounted to the camera by using conduit gland (US: conduit

fitting). The conduit gland is not included to the package of the dome camera and has to be

purchased separately from local providers.

While purchasing conduit gland, the installer only needs to know the camera-side dimension. It

is 3/4”(trade size), or with actual physical diameter of 26.441mm. All the following ACTi

models have the same hole dimension: ACM-7411, ACM-7511, TCM-7011, TCM-7411,

TCM-7811, KCM-7111, KCM-7211.

As for the size of the other end of the conduit gland (hosting the flex conduit), it is up to the

user to decide. Different sizes are available in the market. It is recommended to use the size

that can host at least 1/2”(trade size) tubing so that the Ethernet cable together with RJ-45

head can go through it smoothly.

The following chapter explains how to mount the flex conduit to the camera by using conduit

gland.

www.acti.com

2

Installation of Conduit

Have the Ethernet cable inserted through the

flex conduit together with RJ-45 connector.

You may also consider to do the RJ-45

connector crimping after pushing the cable

through the conduit.

Disassemble the conduit gland.

Slide the clamping nut around flex conduit

some 10-20 cm away from the top. Fit the

sealing insert (made of rubber) to the top of

the flex conduit.

On the camera side, decide which of the 2 possible holes you are going to use to connect the

flex conduit. There is one hole on the side, and one on the bottom. Whichever you pick,

remember to seal off the other one with the metal patch (included in the camera set).

www.acti.com

3

Scenario 1 –using the side hole. Scenario 2 –using the bottom hole.

Screw the body of the conduit gland into the camera and fix it with the lock nut (included in

the set of conduit gland that you purchased) from the inside of the camera..

Connect the Ethernet cable to the camera’s network port.If you are not using PoE, then please

remember to pull the DC power cable through the flex conduit as well, and connect to the

camera at this point.

www.acti.com

4

Push the head of the flex conduit, wrapped with sealing insert, into the body of the conduit

gland.

Screw the clamping nut tightly onto the body of the conduit gland.

Adjust the viewing angle and focus of the camera and put the dome cover back on, and tighten

it by using the screws.

You have completed a fully waterproof installation!

www.acti.com

5

Installation in Humid Environment

Sometimes the installation has to be conducted in a rainy day or in a very humid environment.

In such cases the main concern is the humidity that would remain inside the camera and might

produce fog on the dome cover later.

In case of proper use of conduit, this is not the concern –the flex conduit acts as the ventilation

system linking to the dry indoor environment and eventually the humidity caused by the

installation in rainy day will be gone!