ACTi B4 Series Manual de usuario

Este manual sirve para los siguientes modelos

4

Tabla de contenidos

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

2014/05/06

Bullet with Integrated

Bracket (B4x)

Mounting on a Hard Ceiling

using the Ceiling Bracket

Installation Guide

For Models:

B41, B44, B45, B47

www.acti.com

Installation Guide

2

Table of Contents

Installation Procedures .....................................................3

Step 1: Disconnect the Ethernet Cable.................................................... 3

Step 2: Remove the Integrated Bracket................................................... 4

Step 3: Insert the Cable Through the Ceiling Bracket............................ 6

Step 4: Connect the Cable to the Camera ............................................... 8

Step 5: Attach the Ceiling Bracket to the Camera................................... 9

Step 6: Install the Camera to the Ceiling ............................................... 10

Step 7: Waterproof and Connect the Network Cable.............................11

Step 8: Connect to Network.....................................................................11

Step 9: Access the Camera Live View ....................................................11

Step 10: Adjust the Viewing Angle and Focus ...................................... 12

Waterproof Solution Using the “Pigtail” ........................13

How to Use the Female Cable Gland...................................................... 14

How to Use the Female Conduit Gland.................................................. 17

Appendices.......................................................................21

How to Access the Camera Live View.................................................... 21

Safety Information............................................................28

www.acti.com

Installation Guide

3

Installation Procedures

The camera comes with an integrated bracket used for wall installations. To mount the camera on

the ceiling, replace the integrated bracket with the Ceiling Bracket (PMAX-1300).

NOTE: Screws for ceiling installation are not supplied with the camera or the ceiling bracket

package. Purchase applicable screws separately according to the material of the ceiling where

the camera will be installed.

IMPORTANT! Before installation, make sure the ceiling can bear more than the weight of the

camera and its bracket.

Step 1: Disconnect the Ethernet Cable

Before replacing the integrated bracket, the network cable or “pigtail” must be disconnected and

removed from the camera first.

1. Loosen the four (4) screws to remove the back cover of the camera.

2. Disconnect the network cable from the Ethernet port and let it loose.

NOTE: This network cable is the other end of the “pigtail”.

www.acti.com

Installation Guide

4

Step 2: Remove the Integrated Bracket

1. Using the bundled camera base wrench, detach the two (2) screws to remove the bracket.

2. Remove the clamping nut and sealing insert.

3. Pull the “pigtail” from the camera.

www.acti.com

Installation Guide

5

4. Remove the sealing insert and clamping nut from the cable, and then pull out the “pigtail”

from the bracket.

5. Loosen the two (2) screws using the bundled bracket wrench to detach the bracket (B) from

the main bracket (A).

A

B

www.acti.com

Installation Guide

6

Step 3: Insert the Cable Through the Ceiling Bracket

1. Determine how the cable will be routed: pass through the ceiling or along the ceiling.

If the cable will pass through the ceiling, insert the “pigtail” through the top hole of

the ceiling bracket.

If the cable will be routed along the ceiling, insert the “pigtail” through the side

hole of the ceiling bracket.

2. Insert the “pigtail” through the main bracket.

www.acti.com

Installation Guide

7

3. Insert the clamping nut into the Ethernet cable.

4. Insert the sealing insert with the claw.

www.acti.com

Installation Guide

8

Step 4: Connect the Cable to the Camera

1. Insert the Ethernet cable through the bottom hole of the camera.

2. Pull the cable towards the back of the camera, and then connect the cable to the Ethernet

port.

3. Tighten the four (4) screws to attach the back cover to the camera.

www.acti.com

Installation Guide

9

Step 5: Attach the Ceiling Bracket to the Camera

1. Insert the sealing insert through the gland body and attach the clamping nut.

NOTE: Make sure the clamping nut is tightly attached to the gland body and the sealing

insert is squeezed tightly.

2. Secure the two (2) screws using the bundled bracket wrench to attach the main bracket to the

camera.

3. Push the excess length of cable through the ceiling bracket and align the ceiling bracket to

the main bracket.

www.acti.com

Installation Guide

10

4. Tighten the two (2) screws to secure the ceiling bracket to the main bracket.

Step 6: Install the Camera to the Ceiling

If necessary, drill the screw holes using the supplied drill template. If the cable will pass through

the ceiling, drill the cable hole and route the network end of the camera through that cable hole.

Otherwise, simply attach the camera to the ceiling using four (4) screws.

NOTE: Screws for ceiling installation are not supplied with the camera nor the ceiling bracket

package. Purchase applicable screws separately according to the material of the ceiling where

the camera will be installed.