ACTi ACM-3511 Manual de usuario

www.acti.com

ACTi

Knowledge Base

Category: Installation & Configuration Note

Sub-category: Application

Model: ACM-3511/ACM-3011

Firmware: N/A

Software: N/A

Author: Victor.Wang

Published: 2009/09/02

Reviewed: 2010/01/21

1

Tips for 3-Inch Dome Installation

Contents

Introduction

Installation of camera plate

Installation of camera

Installation of front cover

Future design and improvement

Introduction

Some customers have a problem with installing a 3 inches dome. After adjusting the viewing

angle, zoom or focus, the lens part will be moved again by the rubber and black plastic cover

when they closing the dome cover.The purpose of this document is to guide customer through

the procedures of installing a 3 inches dome efficiently.

Installation of camera plate

1. Use the drill template, and drill a hole with φ35 on the ceiling.

www.acti.com

2

2. Fasten the plate with the camera.

3. Mark on the plate in the direction of the ACTi logo. (the butterfly)

4. Put the camera under ceiling. Adjust the ACTi logo on the camera (the butterfly) toward

the area or object you want to shoot.

5. Mark on the ceiling in the direction of the ACTi logo (the butterfly).

www.acti.com

3

6. Remove the camera from the plate. Tighten the plate to ceiling with M4*20 screws. Make

sure the mark on the plate aims at the mark of step 5.

Installation of camera

7. Connect cables through the hole on the ceiling and plate, or on the side of

casing.

www.acti.com

4

8. Fasten the camera to ceiling by turning clockwise direction.

9. Insert the cable (power/Network/audio) through the mounting plate and

connect to the camera. Then use the little strap in bundled accessory to fasten

the network cable.

www.acti.com

5

10. Fasten the camera to the ceiling. The ACTi logo (the butterfly) should now be

toward to the area or object you want to shoot.

Installation of front cover

11. Remove the front cover

12. Adjust the zoom or focus of the lens. (the lens and the ACTi logo should align

and be toward the area or object you want to shoot)

www.acti.com

6

13. Once you finish the adjustment, pan the lens counterclockwise for around 90

degrees to aim to the arrow on the camera cover.

14. Fasten the front cover to the camera by turning clockwise direction as quickly as

possible. The lens would be moved back to align to the ACti logo.

www.acti.com

7

Future design and improvement

15. In the next generation dome products, the front cover will be fastened to

camera by screws. Since we don't need to turn the front cover, the lens won't be

moved after adjustment.

Future design of ACTi Indoor Dome

Future design of ACTi Outdoor Dome

Otros manuales para ACM-3511

1

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario