ACTi ACM-1511 Series Manual de usuario
Megapixel IP IR DN PoE Bullet Camera
(with DC 12V / PoE)
ACM-1511 series
Ver. 120312
Quick Installation Guide
0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-1511 series
(DC12V / PoE)
The bracket is not included
Product CD Terminal Block for Power
Warranty Card
1
0-2
1.2 PHYSICAL DESCRIPTION
1. Audio Input / Output
The Megapixel IP IR DN PoE Bullet Camera supports audio input
and output with earphone jack
2. Power Input
If your power input is DC12V , please follow the description on
the connector to connect to power.
3. Ethernet Port
The Megapixel IP IR DN PoE Bullet Camera connects to the
Ethernet via a standard RJ45 connector. Supporting NWAY, this
Megapixel IP IR DN PoE Bullet Camera can auto detect the speed
of local network segment (10Base-T/100Base-TX Ethernet).
4. Reset Button
Step 1: Switch off Megapixel IP IR DN PoE Bullet Camera by
disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect
PIN
NAME
DESCRIPTION
1
12V
DC Power Input
2
GND
Ground Pin
0-3
the power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed for a while,
release the reset button. The unit will start up with factory default
settings.
5. Power LED Indicator
The LED indicator lights up one time upon power up. It will
lights up again when this Megapixel IP IR DN PoE Bullet Camera
is fully booted up.
0-4
1.3 BASIC CONNECTIONS
Follow the procedures below to connect the Megapixel IP IR DN PoE
Bullet Camera to the respective apparatuses.
1. Connect the power adaptor to Megapixel IP IR DN PoE Bullet Camera
2. Connect Megapixel IP IR DN PoE Bullet Camera’s ethernet port to an
Ethernet (RJ45 connectors). If your Megapixel IP IR DN PoE Bullet
Camera has PoE built-in, you can regard it as a PD and connect it directly
to a PSE device like PoE switch.
3. Connect a PC to the Ethernet hub (RJ45 connectors)
1
NOTE: You may find a support package for help you getting familiar
with PoE. Please visit our web site, and get the support document
TS-00040.
0-5
1.4 Installation Procedure
1.4.1 Install the camera onto bracket
1.4.2 Rotate camera box counter-clockwise to remove camera
cover
0-6
1.4.3 Adjust the focus / zoom
- Zoom adjust lever
- Focus adjust lever
1-7
1Quick Tour
This section guides you with a quick tour on this Megapixel IP IR DN PoE Bullet
Camera.
2.1 Configure this Megapixel IP IR DN PoE Bullet Camera
2.1.1 Make sure network environment
Default IP of this Megapixel IP IR DN PoE Bullet Camera is 192.168.0.100. Please
make sure this Megapixel IP IR DN PoE Bullet Camera and your PC are on the same
network segment before running the installation.
2.1.2 Open Internal Explorer with IP address
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)
1-8
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: This Megapixel IP IR DN PoE Bullet Camera default IP address is
set to 192.168.0.100
2.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.
2.1.4 Preview the video
Otros manuales para ACM-1511 Series
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de ACTi
ACTi
ACTi ACM-3401 Series Manual de usuario
ACTi
ACTi KCM-7311 Manual de usuario
ACTi
ACTi B94 Manual de usuario
ACTi
ACTi ACM-7411 Series Manual de usuario
ACTi
ACTi E911 Manual de usuario
ACTi
ACTi A310 Manual de usuario
ACTi
ACTi E12A Manual de usuario
ACTi
ACTi A425 Manual de usuario
ACTi
ACTi E11A Manual de usuario
ACTi
ACTi E616 Manual de usuario
ACTi
ACTi KCM-5211E Manual de usuario
ACTi
ACTi D9 Series Manual de usuario
ACTi
ACTi Z81 Manual de usuario
ACTi
ACTi A3 Series Manual de usuario
ACTi
ACTi B21 Manual de usuario
ACTi
ACTi ACM-1430 series Manual de usuario
ACTi
ACTi E933 Manual de usuario
ACTi
ACTi E37 Manual de usuario
ACTi
ACTi ACM-3001 Instrucciones de uso
ACTi
ACTi E33 Manual de usuario
