ACME STAGE PAR 400 ZOOM IP Manual de usuario

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. How To Set The Fixture .................................................................................. 5

3.1 Control Panel ........................................................................................... 5

3.2 Main Functions ........................................................................................ 6

4. How To Control The Unit.............................................................................. 13

4.1 DMX512 Controller ................................................................................ 14

4.2 DMX512 Configuration........................................................................... 14

4.3 DMX512 Connection.............................................................................. 18

5. Troubleshooting........................................................................................... 19

6. Fixture Cleaning........................................................................................... 19

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is suitable for indoor use and wet locations. Do not immerse in water.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head

only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 75℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

Please read the instruction carefully which includes important information

about the installation, usage and maintenance.

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

0.5 meters.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of

the reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

250W

Light Source:

7x40W RGBW LED

Zoom Range:

Beam Angle: 6°~40°

Spot Angle: 10°-60°

Dimmer/Shutter:

Smooth dimming from 0~100%; outstanding strobe effect with variable speed

Control:

DMX Channel: 5/7/9 channels

Control Mode: DMX512, RDM

Firmware Upgrade via DMX link

Construction:

Display: OLED display

Data In/Out: 5-pin IP XLR

Power In/Out: Waterproof Power Connector in/out

Protection Rating: IP66

Features:

Built-in programs for selection

Can change the DMX address code, machine reset, voice mode conversion and other functions

from the console

Uniform RGBW color mixing and rainbow effect

Advanced RDM function

IP66 protection rating, can be used outdoors all year round

Dimensions/Weight:

295x316x318mm, 8.5kgs

11.6"x12.4"x12.5"in, 18.7lbs

Photometrics Diagram:

3. How To Set The Fixture

3.1 Control Panel

1. Display: To show the menu and the selected functions

2. Button:

MENU To select the programming functions

DOWN To go forward in the selected functions

UP To go backward in the selected functions

ENTER To confirm the selected functions

3. DMX IN: For DMX512 operation, use 5-pin XLR cable to link the DMX controller

4. DMX OUT: For DMX512 operation, use 5-pin XLR cable to link the next unit

5. POWER IN: Connects to supply power

6. POWER OUT: Connects to the next fixture

3.2 Main Functions

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The screen will be automatically locked if there is no operation for a long time, and can be

unlocked by long-pressing the MENU button.

The main functions are shown below:

DMX Setting

To select DMX Setting,press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address or Channel Mode.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust

the address from 001 to 512, press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select 5

CH, 7 CH or 9 CH, press the ENTER button to store. Press the MENU button back to the last menu

or let the unit idle 30 seconds to exit menu mode.

DMX State

To select DMX State, press the ENTER button to confirm, use the UP/DOWN button to select Last

State, Blackoutor Show.

Fixture Setting

To select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN button to select

Primary/Secondary, Light Mode, Constant Color, Dimmer Curve, Dimmer Speed, Fan Mode or

PWM Frequency.

Primary/Secondary

To select Primary/Secondary, press the ENTER button to confirm. Use the UP/DOWN button to

select Primary or Secondary, press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Light Mode

To select Light Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

Color Correction or White Balance, press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle 30 seconds to exit menu mode.

Constant Color

To select Constant Color, press the ENTER button to confirm. Use the UP/DOWN button to select

No or Yes, press the ENTER button to store. Press the MENU button back to the last menu or let

the unit idle 30 seconds to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to confirm. Use the UP/DOWN button to select

Optically Linear, Square Law, Inverse Square Law or S-Curve, press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.

Optically Linear:The increase in light intensity appears to be linear as DMX value is increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law:Light intensity control is coarser at low levels and finger at high levels.

S-Curve: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Dimmer Speed

To select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select

Smooth or Fast, press the ENTER button to store. Press the MENU button back to the last menu or

let the unit idle 30 seconds to exit menu mode.

Fan Mode

To select Fan Mode, press the ENTER button to confirm. Use the UP/DOWN button to select Auto

or Silent, press the ENTER button to store. Press the MENU button back to the last menu or let the

unit idle 30 seconds to exit menu mode.

PWM Frequency

To select PWM Frequency, press the ENTER button to confirm, use the UP/DOWN button to

select 600Hz, 1200Hz, 2400Hz, 3600Hz, 4800Hz, 6000Hz, 10200Hz, 15000Hz, 20400Hz, 25200Hz

or 28800Hz, press the ENTER button to store. Press the MENU button back to the last menu or let

the unit idle 30 seconds to exit menu mode.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de ACME

ACME

ACME LED-PS10D RGBW Manual de usuario

ACME

ACME LED-WAV-10W Manual de usuario

ACME

ACME Andromeda Manual de usuario

ACME

ACME BF-1500ND B Manual de usuario

ACME

ACME ColorTec 250 LED-CC60 Manual de usuario

ACME

ACME Uploader II Manual de usuario

ACME

ACME DMX512 Dynamic Scan Manual de usuario

ACME

ACME LED-900 A Manual de usuario

ACME

ACME Dynamic 25 Spin LED?GF25 Manual de usuario

ACME

ACME SABER HYBRID PRO Manual de usuario

ACME

ACME TV LIGHT PANEL 2000 Manual de usuario

ACME

ACME Thunderstruck LP-2304 Manual de usuario

ACME

ACME Solar Flare Manual de usuario

ACME

ACME PEXEL 100 Manual de usuario

ACME

ACME COMET Manual de usuario

ACME

ACME LED-HC50 II Manual de usuario

ACME

ACME SAMURAI SCAN 50 Manual de usuario

ACME

ACME FESTIVAL Manual de usuario

ACME

ACME iSolution Manual de usuario

ACME

ACME Diamonds II Manual de usuario

ACME

ACME XP-280 BS Manual de usuario

ACME

ACME Diabolo Manual de usuario

ACME

ACME Beluga Manual de usuario

ACME

ACME LED-HC101 II Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario