ACME SPLENDOR 90 Manual de usuario

Splendor 90

CM-90

User Guide

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Change Beam Angle

4. How To Set The Unit

4.1 Control Panel

4.2 Main Function

5. How To Control The Unit

5.1 Master/Slave Built-in Preprogram Function

5.2 Easy Controller

5.3 DMX Controller

6. Troubleshooting

7. Fixture Cleaning

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there is no flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit.

Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is

higher than this.

In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

Do not touch any wire during operation as high voltage might be causing electric shock.

Warning

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

Do not open the unit within five minutes after switching off.

The housing, the lenses must be replaced if they are visibly damaged.

Please read carefully the instruction, which includes important

information about the installation, usage and maintenance.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its metal hole on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a 10 times

weight of the unit.

2. Technical Specification

DMX Channels: 16/9 channels

Great built-in lighting shows under Master/Slave mode triggered by music

Through its flexible installation options the unit can be installed in various orientations

The sound sensitivity can be adjust in the menu of LCD display

It is perfect for professional stage, theatre, TV, exhibition and architectural application

Voltage

：

AC 100-240V~50/60Hz

Power consumption: 390W

Light Source: total: 3W LED x 90pcs

Red: 18pcs, Green: 24pcs, Blue: 24pcs, Amber/White: 24pcs

Fuse: T 6.3A

Beam Angle: 15°/25°

Dimension: 335 x 227 x 386 mm

Weight: 10 kgs

3. Change Beam Angle

If you want to change the beam angle of the fixture, you can change lens of the

fixture refer to the photo below:

4. How To Set The Unit

4.1 Control Panel

Display

To show the various menus and the selected functions

LED

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

Turn off the mains power

first, or high voltage may

cause electric shock!

Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Fuse

For over current protection.

Only for remote control

By connect to the 1/4’’ microphone jack to control the unit for Stand by, Function and Mode

function.

Mains input

Connect to supply mains power.

DMX input/output

For DMX512 link, use 3/5-pin XLR plug cable to link the unit together.

4.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWNand UP button to change the mode. Once the required mode has been selected,

Press ENTER button to store. Back to the main functions without any change press the

MENU button or wait for 8 seconds.

Hold MENU button to quit menu mode, the unit will run the built-in program you selected.

The main functions are shown below:

DMX Address

Press the MENU button up to when the DMX Address is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to change the DMX512

address. Once the address has been selected, press the ENTER button to store. Back to

the main functions without any change press the MENU button or wait for 8 seconds.

Channel Mode

Press the MENU button up to when the Channel Mode is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to select the Mode 1 (9)

or Mode 2 (16). Once selected, press the ENTER button to store. Back to the main functions

without any change press the MENU button or wait for 8 seconds.

Show Mode

Press the MENU button up to when the Show Mode is showing on the display. Press

ENTER button, the display will blink. Press DOWN and UP button to select Show 1 or Show

2 or Show 3 or Show 4, once selected, press MENU button to store. Back to the main

functions without any change press the MENU button or wait for 8 seconds.

Slave Mode

Press the MENU button up to when the Slave Mode is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to select the slave 1 or

slave 2 mode. Once selected, press the ENTER button to store. Back to the main functions

without any change press the MENU button or wait for 8 seconds.

Sound State

Press the MENU button up to when the Sound State is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to select the on (sound

control on) or off (sound control off) mode. Once selected, press the ENTER button to store.

Back to the main functions without any change press the MENU button or wait for 8

seconds.

Sound Sense

Press the MENU button up to when the Sound Sense is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to adjust the sound

sensitively (1-100) of the unit. Once the value has been selected, press the ENTER button

to store. Back to the main functions without any change press the MENU button or wait for 8

seconds.

Black Out

Press the MENU button up to when the Black Out is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the yes (yes

blackout) or no (no blackout) mode. Once selected, press the ENTER button to store. Back

to the main functions without any change press the MENU button or wait for 8 seconds.

Pan Inverse

Press the MENU button up to when the Pan Inverse is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (pan inverse) mode. Once selected, press the ENTER button to store. Back

to the main functions without any change press the MENU button or wait for 8 seconds.

Tilt Inverse

Press the MENU button up to when the Tilt Inverse is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (pan inverse) mode. Once selected, press the ENTER button to store. Back

to the main functions without any change press the MENU button or wait for 8 seconds.

Back Light

Press the MENU button up to when the Back Light is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the on (back

light on) or off (back light off 1 minute after auto show) mode. Once selected, press the

ENTER button to store. Back to the main functions without any change press the MENU

button or wait for 8 seconds.

Display Inverse

Press the MENU button up to when the Display Inverse is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (display inverse) mode. Once selected, press the ENTER button to store.

Back to the main functions without any change press the MENU button or wait for 8

seconds.

Auto Test

Press the MENU button up to when the Auto Test is showing on the display. Pressing

ENTER button and the display will show Test… and the unit will run self-test by built-in

program. To go back to the functions press the MENU button.

Manual Test

Press the MENU button up to when the Manual Test is showing on the display. Press

ENTER button and Pan will blink, use UP and DOWN button to choose Tilt or Red or Green

or Amber/White or Strobe or Dimmer, press ENTER button to enter, then press UP and

Down button to adjust the value and press ENTER button to set next optional. Back to the

main functions without any change please press the MENU button.

White Balance

Press the MENU button up to when the White Balance is showing on the display. Press

ENTER button and the Red will blink, press UP and Down button to adjust the value, press

ENTER button to store and Green will blink on the display, press UP and Down button to

adjust the value, press ENTER button to store and Blue will blink on the display, press UP

and Down button to adjust the value, and press ENTER button to store. Back to the main

functions without any change please press the MENU button.

Temperature Unit

Press the MENU button up to when the Temperature Unit is showing on the display.

Pressing ENTER button and the display will blink. Use DOWN and UP button to select ℃

or ℉. Once selected, press the ENTER button to store. Back to the main functions without

any change press the MENU button or wait for 8 seconds.

Fixture Time

Press the MENU button up to when the Fixture Time is blinking on the display. Pressing

ENTER button and the display will show the number of working hours of the unit. To go back

to the functions press the MENU button.

Language

Press the MENU button up to when the Temperature Unit is showing on the display.

Pressing ENTER button and the display will blink. Use DOWN and UP button to select

English or Chinese. Once selected, press the ENTER button to store. Back to the main

functions without any change press the MENU button or wait for 8 seconds.

Fixture Temp

Press the MENU button up to when the Fixture Temp is blinking on the display. Pressing

ENTER button and the display will show the temperature of the unit. To go back to the

functions press the MENU button.

Reset

Press the MENU button up to when the Reset is blinking on the display. Pressing ENTER

button and all motors will back to their home position. To go back to the functions press the

MENU button.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de ACME

ACME

ACME LED-920D Manual de usuario

ACME

ACME LED-MTX36 HEX Manual de usuario

ACME

ACME SAMBA Color Manual de usuario

ACME

ACME XP-470 BSW Manual de usuario

ACME

ACME LED-PAR 100 WW/CW Manual de usuario

ACME

ACME SAM-50 Manual de usuario

ACME

ACME CA-DD12 II Manual de usuario

ACME

ACME LED-MTX25 IP Manual de usuario

ACME

ACME MINI ELLIPSOIDAL 10 Manual de usuario

ACME

ACME LED?7TC Manual de usuario

ACME

ACME RAYZOR HYBRID XA-100 BSW Manual de usuario

ACME

ACME E-10 WW DXX Manual de usuario

ACME

ACME Ellipsoidal E-300 D2550 Manual de usuario

ACME

ACME LED-ST1000 Manual de usuario

ACME

ACME Dotline360 TB-1230 QW Manual de usuario

ACME

ACME iColorLed 18TC Manual de usuario

ACME

ACME MH-275R Manual de usuario

ACME

ACME MH-600A Mobile Color Manual de usuario

ACME

ACME E-200 MB MC Manual de usuario

ACME

ACME Dotline 360 Manual de usuario

ACME

ACME XP-1000WZ Manual de usuario

ACME

ACME ORION XP-260 BEAM Manual de usuario

ACME

ACME XP-1200F Manual de usuario

ACME

ACME Ellipsoidal 10 DMX Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario