Accton Technology Zilla Dual-Speed Hub-3008R Manual de usuario

Zilla Dual-Speed Hub-3008R

Quick Installation Guide

Introduction

Accton’s Zilla Hub is a compact dual-speed hub featuring 8

10BASE-T/100BASE-TX auto-sensing ports.This hub is

completely plug and play, no configuration necessary. This

dual-speed hub contains two internal repeater buses – one for

10Mbps traffic and another for 100Mbps traffic. Traffic passing

between attached devices that operate at the same speed is

confined within the appropriate repeater bus.

The components of the Zilla Hub are shown in the figure

below:

Zilla Hub

Check the Package

The Zilla Hub includes:

• 1 Zilla Hub • 1 DC Power Adapter

• This user guide • 1 registration card (please return)

RJ-45 Connectors

Accton’s Zilla Hub features 8 10BASE-T/100BASE-TX ports

with RJ-45 connectors located on the side panel of the hub.

Ports 1-8 are (computer) station ports. To connect to a

workstation or server, attach straight-through unshielded or

shielded twisted-pair cabling to any station port on this hub.

Port 8 doubles as a station (computer) port and a cascade

(uplink) port. The cascade port makes it convenient to connect

cable from the hub to a station port on another hub or a

switch.

Mount the Hub

The Zilla Hub can be placed directly on your desktop or

stuck to a metallic vertical surface (using the magnetic foot

pads on the bottom of the hub).

Before you start installing the hub, be sure you find a

suitable location at the center of the devices you want to link

and near a power outlet.

Connect PCs to the Hub

1. Remove the rubber cover from an RJ-45 port.

Quick Installation Guide

2. Install a 10 or 100 Mbps (10BASE-T or 100BASE-TX)

network adapter card and driver in each

computer you want to network.

3. Prepare straight-through

twisted-pair cables with RJ-45

plugs. Attach one end of the

cable to the RJ-45 port of the

computer’s network adapter

card and the other end to any

available port on the hub.

Notes: If you are using port 8, be

sure the Daisy-Chain switch is set to "COMPUTER."

Cascade Devices to the Hub

If you need more ports, connect a station port on another

device to the cascade port on the Zilla hub with straight-

through twisted-pair cable, maximum 5 meters (19.68 feet).

1. To make a direct connection to another compatible hub or

switch, use the RJ-45 cascade port 8. Set the port

selection switch to HUB and then

connect to any station port on the

other device. Alternatively, you

can connect from any RJ-45

station port on the hub to an

uplink port on the other device.

2. Prepare straight-through shielded

or unshielded twisted-pair cables

with RJ-45 plugs at both ends.

Use 100Category 3, 4 or 5

cable for standard 10Mbps

Ethernet connections, or 100

Category 5 cable for 100Mbps Fast

Ethernet connections. When inserting an RJ-45 plug, be

sure the tab on the plug clicks into position to ensure that

it is properly seated.

Notes: 1. Make sure each twisted-pair cable does not

exceed 100 meters (328 feet).

2. To connect to another hub or switch, you may

also attach to station ports at both ends if you

use crossover cabling.

Zilla Hub

Verify System Operation

Check each connection by viewing the port status indicators

shown in the following table. The hub monitors the link status

for each port. If the Port indicator fails to light when you

connect a device to the hub, follow the troubleshooting advice

detailed in the next section.

sDELsutatSbuHdnatroP

sDELnoitidnoCsutatS

rewoPnO.rewopgniviecersibuH

kniLnO001/01dilavadehsilbatsesahtroP

.noitcennockrowtenspbM

ytivitcAgnihsalF.tropehtgnisrevartsiciffarT

Troubleshooting

Symptom: Power LED does not light after power on.

Cause: Power outlet or power cord may be defective.

Solution: 1. Check for loose connections.

2. Check the power outlet by using it for another

device.

3. Replace the power cord.

Symptom: Port LED does not light after connection is made.

Cause: Hub port, network card or cable may be

defective.

Solution: 1. Check that the hub and attached device are

both powered on.

2. Be sure the network cable is connected to both

devices.

3. Verify that Category 5 cable is used for

100Mbps connections and that the length of

any cable does not exceed 100 meters (328

feet).

4. Check the network card and cable connections

for defects.

5. Replace the defective card or cable if

necessary.

Quick Installation Guide

Application Diagram

Zilla Hub

Specifications

Standards Conformance IEEE 802.3 10BASE-T, IEEE 802.3u

100BASE-TX

Number of Ports 8 10/100 Mbps RJ-45 ports (one of which

serves as a daisy-chain port)

Network Interface RJ-45: 100, UTP cable

10BASE-T: Category 3, 4 or 5

100BASE-TX: Category 5

Switching Method Store-and-forward

MAC Address Table 2K entries per system

Memory Buffer 128 Kbytes per system

Filtering Rate Line speed

Forwarding Rate 14,810 pps (at 10 Mbps ),

148,810 pps (at 100 Mbps )

Learning Rate Line speed

Dimensions 90 x 97.5 x 24 mm

Weight 160 gm

Power Requirements 10 VDC,0.6 A (from external power adapter)

Power Consumption 6 Watts maximum

Heat Dissipation 20.5 BTU/hr

Maximum Current 0.6 A @ 10 VDC

Access Method CSMA/CD, 10 Mbps and 100 Mbps

Status LEDs Power, Link, Activity

Environmental

Temperature 0°C to 40°C

-40° - 70°C / -40° - 158°F (storage)

Humidity IEC721-2-1, 10% to 85% (non-condensing)

Certification CE Mark

Emissions FCC Class B, VCCI Class B, CISPR 22 Class B,

EN55022 Class B

Safety CSA/NRTL, TÜV/GS,CB

Quick Installation Guide

Certification

FCC Class B Certification

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Warning: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different

from the one which the receiver is connected to

• Consult the dealer or an experienced radio/TV technician for

help

You are cautioned that changes or modifications not expressly

approved by the party responsible for compliance could void

your authority to operate the equipment.

Note: In order to maintain compliance with the limits of a

Class B digital device, Accton requires that you use a quality

interface cable when connecting to this device. Changes or

modifications not expressly approved by Accton could void your

authority to operate this equipment. Suggested cable type is

unshielded or shielded (UTP/STP) cable – Category 3 or

greater for 10Mbps connections, and Category 5 for 100Mbps

connections.

Class B (Canada Department of Communications)

This digital apparatus does not exceed the Class B limits for

radio noise emissions from digital apparatus as set out in the

interference-causing equipment standard entitled "Digital

Apparatus", ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits

radioélectriques applicables aux appareils numériques de

Classe B prescrites dans la norme sur le matériel brouilleur:

"Appareils Numérques", NMB-003 édictée par le ministère des

Communications.

Zilla Hub

VCCI Class B Compliance (Japan)

CE Mark Declaration of Conformance (for EMI

and Safety - Europe)

This is to certify that this product complies with ISO/IEC Guide

22 and EN45014. It conforms to the following specifications:

EMC: EN55022(1988)/CISPR-22(1985) class B

EN60555-2(1995) class B

EN60555-3

IEC1000-4-2(1995) 4kV CD, 8kV AD

IEC1000-4-3(1995) 3V/m

IEC1000-4-4(1995) 1kV - (power line),

0.5kV - (signal line)

IEC1000-4-6(1995) 3Vrms

This product complies with the requirements of the Low Voltage

Directive 73/23/EEC and the EMC Directive 89/336/EEC.

Warning! Do not plug a phone jack connector in the RJ-45 port.

This may damage this device. Les raccordeurs ne sont pas

utilisé pour le système téléphonique!

Tabla de contenidos

Otros manuales de Cambiar de Accton Technology

Accton Technology

Accton Technology USB204A Manual de usuario

Accton Technology

Accton Technology EtherHub-24s Manual de usuario

Accton Technology

Accton Technology CheetaHub Power-3008P Manual de usuario

Accton Technology

Accton Technology Fast EtherHub-12s Manual de usuario

Accton Technology

Accton Technology Volare Sensor 2 Manual de usuario

Accton Technology

Accton Technology VS4512DC Manual de programación

Accton Technology

Accton Technology CHEETAHUB POWER-3012A Manual de usuario

Accton Technology

Accton Technology EtherHub-16 Manual de usuario

Accton Technology

Accton Technology Cheetah iSharer-3010 Manual de usuario

Accton Technology

Accton Technology CheetaHub Power-3012B Manual de usuario

Accton Technology

Accton Technology CheetaHub Power-3004E Manual de usuario

Accton Technology

Accton Technology CheetaHub Power-3008N Manual de usuario

Accton Technology

Accton Technology Fast EtherHub-8s Manual de usuario

Accton Technology

Accton Technology SuperSmart EtherHub-16se Manual de usuario

Accton Technology

Accton Technology CheetahSwitch Workgroup-2027 Manual de usuario

Accton Technology

Accton Technology USB204B Manual de usuario

Accton Technology

Accton Technology Fast EtherHub 3500 Series Manual de usuario

Accton Technology

Accton Technology Edge-Core ES4528V Manual de usuario

Accton Technology

Accton Technology USB204A Manual de usuario

Accton Technology

Accton Technology ES3616 Manual de programación

Accton Technology

Accton Technology 24/48 10/100 Ports + 2GE Manual de programación

Accton Technology

Accton Technology VM2524 Manual de usuario

Accton Technology

Accton Technology ES4710BD Manual de usuario

Accton Technology

Accton Technology 12se Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario