ABB Zenith ZTG 30 Manual de usuario

OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

Zenith ZTG series

For ZTG(D) series automatic transfer

switches, 30-1200 A, 200-480 Vac

—

Receiving, handling and storage

Receiving and handling

Upon receipt, carefully inspect the trans-

fer switch for damage that may have oc-

curred during transit. If damage is evi-

dent, or there is visible indication of

rough handling, immediately file a dam-

age claim with the transportation com-

pany, and notify your local ABB sales

office.

Do not remove the shipping packaging

until ready to install the switch.

Storage

If the unit will not be placed into service

immediately, store the transfer switch in

its original package in a clean, dry loca-

tion. To prevent condensation, maintain a

uniform temperature. Store the unit in a

heated building, allowing adequate air cir-

culation and protection from dirt and

moisture. Storing the unit outdoors could

cause harmful condensation inside the

transfer switch enclosure.

HAZARD OF EQUIPMENT

OVERTURNING

When moving with a fork lift, do not re-

move the shipping packaging until the de-

vice is in its final location.

Failure to follow this instruction may

result in personal injury or equipment

damage.

Warning

Indicates a hazardous situation that,

if not avoided, could result in death or

serious injury.

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

—

Read these safety instructions

carefully before using this product!

HAZARD OF ELECTRIC SHOCK,

EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective

equipment and follow safe electrical

work practices.

• This equipment must only be installed

and serviced by qualified electrical per-

sonnel.

• Before performing visual inspections,

tests, or maintenance on the equip-

ment, disconnect all sources of electric

power. Assume that all circuits are live

unless they are completely de-ener-

gized, tested, grounded, and tagged.

Pay particular attention to the design of

the power system. Consider all sources

of power, including the possibility of

backfeeding.

• Disconnect all sources of electric power

before removing or making source side

or load side connections to the transfer

switch.

• Always use a properly rated voltage

sensing device at all line and load con-

nections to confirm transfer switch is

disconnected from all live electrical

sources.

• Turn off power supplying transfer

switch before doing any other work on

or inside switch.

Failure to follow these instructions could

result in death or serious injury.

Danger

Indicates a hazardous situation that,

if not avoided, will result in death or

serious injury.

—

Operation, maintenance,

and installation

instruction

Automatic transfer

switches, Zenith ZTG

series ATS

INSTALLATION INSTRUCTIONS,

ZENITH ZTG SERIES ATS,

CHAPTERS 9–11

OPERATION AND MAINTENANCE

INSTRUCTIONS, ZENITH

ZTG SERIES ATS,

CHAPTERS 1–8

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

—

Operation and

maintenance instruction

Automatic transfer

switches, Zenith ZTG

series ATS

1. Introduction 11

1.1 Hazard Categories 11

1.2 Definitions 12

1.3 Warranty 13

1.4 Product Specification 14

2. Product overview 15

2.1 General overview 16

2.1.1 Operation types 17

2.2 HMI 18

2.3 Zenith ZTG series features 19

2.4 Typical applications 22

2.5 Sequence of operations 24

2.5.1 Switching sequence / Automatic 24

2.6 Special features description 30

2.6.1 Automatic configuration 30

2.6.2 In-phase monitor 30

2.6.3 Powering supply scenarios 30

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

3. General operation 31

3.1 Position indication 31

3.2 Operating and locking 32

3.3 Manual handle operation 33

3.4 Return to automatic mode,

operating by HMI 35

3.5 LED functionality in HMI 36

3.6 Using HMI 38

3.6.1 Keypad 38

3.6.2 Navigating in menu 38

4. Navigating HMI menu 39

4.1 Start screens 39

4.2 Using main menu and setting parameters 41

4.3 Menus and parameters 42

5. Electronic accessories 53

5.1 Using Ekip Connect -software 54

5.2 Using Ekip Bluetooth-module 55

5.2.1 LED indications 55

5.3 Using Ekip Programming -module 56

5.3.1 LED indications 56

5.4 Auxiliary power supply module 57

5.4.1 Electrical characteristics 57

5.4.2 LED indications 57

5.5 Using Ekip Signalling 2K-_ -module 58

5.5.1 Electrical characteristics of 58

Ekip Signalling 2K-_ -module

5.5.2 Access from the display / 58

Ekip Signalling 2K-_ -module

5.5.3 LED indications and inputs/outputs 61

of Ekip Signalling 2K-_ -module

5.6 Using Ekip Com _ -modules 62

5.6.1 Ekip Com Modbus RTU -module 62

5.6.2 Ekip Com Profibus DP -module 65

5.6.3 Ekip Com DeviceNet -module 68

5.6.4 Ekip Com Modbus TCP -module 72

5.6.5 Ekip Com Profinet -module 76

5.6.6 Ekip Com EtherNet/IP -module 79

6. Troubleshooting 83

6.1 Alarms 83

6.2 Warnings 85

6.3 Information 86

7. Technical data 87

7.1 General technical data 87

7.2 Circuit diagrams 90

7.3 Overall dimensions 92

8. Maintenance 95

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de ABB

ABB

ABB vital 1 Manual de usuario

ABB

ABB FAP 1011 Manual de usuario

ABB

ABB NE810 Manual de usuario

ABB

ABB FIP2002 Manual de usuario

ABB

ABB 6953 EB-101-500 Manual de usuario

ABB

ABB VD4 Series Guía rápida

ABB

ABB Power Break II Manual de usuario

ABB

ABB OTM_C Series Guía del usuario

ABB

ABB SIM600 Manual de usuario

ABB

ABB EDS500 Series Manual de usuario

ABB

ABB TruONE ATS OXB250E3S3QT Manual de usuario

ABB

ABB 3299-22958 Manual de usuario

ABB

ABB DY365 Series Manual de usuario

ABB

ABB SACE Tmax XT Manual de usuario

ABB

ABB 3299A-A02100 x Guía de configuración

ABB

ABB FAP1021 Series Manual de usuario

ABB

ABB 3299E-A22100 Manual de usuario

ABB

ABB InLine II ZHBM-ITS Series Manual de usuario

ABB

ABB JSTD20 Manual de usuario

ABB

ABB REL 301 Manual

ABB

ABB OT16F3 Manual de usuario

ABB

ABB OTM C Series Manual de usuario

ABB

ABB SACE Tmax XT2 Manual de usuario

ABB

ABB OWIII Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario