ABB FCAN-01 Manual de instalación

Safety instructions

WARNING! Obey the safety instructions of the drive. If you ignore them, injury or death, or

damage to the equipment can occur.

Mechanical installation

Electrical installation

Layout of the module

1. Pull out the lock.

2. Install the module carefully to an option

module slot of the drive. See the drive

hardware manual.

3. Push in the lock.

4. Tighten the screw to torque 0.8 N·m

using a Torx TX10 screwdriver.

WARNING! Do not use excessive force, or leave the screw too loose. Over-tightening can

damage the screw or module. A loose screw decreases the EMC performance, and can

cause an operation failure.

No. Description

1Lock

2 Mounting and grounding screw

3 Bus connector [X1]

4 Diagnostic LEDs

—

OPTIONS FOR ABB DRIVES

FCAN-01 CANopen adapter module

Quick installation and start-up guide

Start-up

To control the drive with the adapter module, set at least the basic parameters listed in the table

below. For full parameter descriptions, refer to the adapter module’s user manual or to the drive’s

firmware manual.

Basic parameter settings

To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par

refresh.

Further information

Pin allocation for [X1] Bus termination

Bus termination is required to prevent signal reflections from

the bus cable ends. The module is not equipped with internal

bus termination. Therefore, the first and last nodes of the bus

must be included with bus termination.

In the this diagram, the built-on terminations of the D-SUB

connectors at the first and last nodes are switched on.

According to CANopen specification CiA 301.

Pin Description

1 - Not in use

2 CAN_L CAN_L bus line

3 CAN_GND CAN ground

4 - Not in use

5CAN_SHLD OptionalCAN

6 GND Optional ground

7 CAN_H CAN_H bus line

8 - Not in use

9 CAN_V+ Not supported.

Index Name Value

20.01 Ext1 commands Fieldbus A

22.11 Speed ref1 source FBA A ref 1

28.11 Frequency ref1 source FBA A ref 1

50.01 FBA A enable Enable (or select the option slot in which the module is installed)

50.02 FBA A comm loss func Fault

51.02 Node ID Set the node address of the device.

51.03 Bit rate Set the bit rate for the CANopen interface.

51.05 Profile The ABB Drives communication profile is the default value.

See the latest version of FCAN-01 CANopen adapter module

user's manual (3AFE68615500 [English]) in ABB library

(www.abb.com/drives/documents).

For more information on ABB fieldbus options and protocols,

see the fieldbus communications web page

(new.abb.com/drives/connectivity/fieldbus-connectivity).

SUB-D9

(male)

CANopen

CANopen CANopenCANopen

OFF

OFF ON

FCAN-01 manual

Fieldbus communications web

page

Specifications subject to change without notice.

3AXD50000158195 Rev B (EN) 2023-01-25

abb.com/drives

Otros manuales para FCAN-01

Tabla de contenidos

Otros manuales de Unidad de control de ABB

ABB

ABB CMS-660 Manual de usuario

ABB

ABB Busch-ComfortTouch 9 Manual de usuario

ABB

ABB RELION 650 SERIES Guía de inicio rápido

ABB

ABB CMS-700 Manual de usuario

ABB

ABB TruONE Ekip Manual de usuario

ABB

ABB CPTC-02 Manual de usuario

ABB

ABB REC650 ANSI Manual de usuario

ABB

ABB CP-A RU Manual de usuario

ABB

ABB Powernet 6920U-102-500 Manual de usuario

ABB

ABB ACS580-04 Manual de usuario

ABB

ABB RMBA-01 Manual de usuario

ABB

ABB REF542plus Guía

ABB

ABB IEC 61850 Edition 2 Manual de usuario

ABB

ABB MRP31.0 Manual de usuario

ABB

ABB NCAN-02 Manual de instalación

ABB

ABB Relion 615 series Manual de usuario

ABB

ABB BCU-01 Manual de usuario

ABB

ABB TOTALFLOW WellTell Wireless IS Guía del usuario

ABB

ABB COM600 series Manual de usuario

ABB

ABB Relion REC670 Instrucciones de uso

ABB

ABB CMS-660 Manual de usuario

ABB

ABB ACS880-04 drive modules Manual de usuario

ABB

ABB RPBA-01 Manual de usuario

ABB

ABB OHDI-01 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario