3Dlabs X400 Manual de usuario
Page | 1
Rev. 1.04 – 4/16/2021
X400 QUICK START REFERENCE GUIDE
READ THIS DOCUMENT BEFORE USING YOUR 3D PRINTER
Page | 2
CONTENTS
INTRODUCTION AND HOW TO GET HELP ...................................................................................................................... 3
WHAT’S INCLUDED IN YOUR KIT .................................................................................................................................... 3
UNPACKING THE PRINTER CONTENTS ........................................................................................................................... 4
MOVING THE PRINTER ................................................................................................................................................... 6
SETTING UP THE PRINTER .............................................................................................................................................. 6
LOADING MATERIAL ...................................................................................................................................................... 7
STARTING YOUR FIRST 3D PRINT ................................................................................................................................. 14
TROUBLESHOOTING .................................................................................................................................................... 16
Page | 3
INTRODUCTION AND HOW TO GET HELP
We’d like to thank you for purchasing the 3D Labs X400 High Temperature 3D printer. Proudly
assembled and calibrated in the US, in Jacksonville Florida. The X400 is a rugged, industrial grade
machine that will provide years of service and repeatability.
This guide has been assembled to help you quickly get setup and to complete your first successful print.
Please reference our website at https://www.3dlabs.io/support for more complete manuals and
documentation. A full manual and support videos are available there.
Your 3D Labs X400 is a machine tool. As with operating any machine tool, there is a learning curve. 3D
Labs has implemented multiple features to make the machine easier to learn and use. With the proper
time invested, you will learn how to properly operate your 3D printer to it’s max potential and it will give
you the best results.
3D Labs support is here to help you flatten the learning curve. 3D Labs support can be reached by
phone at (904) 201-9593, by email at [email protected]o, or via support ticket at
https://www.3dlabs.io/support should you have any questions.
WHAT’S INCLUDED IN YOUR KIT
1. 3D LABS X400 3D PRINTER
2. QUICK START REFERENCE GUIDE
3. TOOL BAG CONTAINING
a. 3x Hex (allen) wrenches, 3 x wrenches
b. Spare screws and nuts bag
c. Spare heater cartridge and thermistor
d. Spare low temp hotend
e. Spare high temp hotend w/brass nozzle
f. Spare endstop, filament runout sensor
g. 2 x spare brass nozzles
h. Spare spring, knurled nut, and screw for tension assembly
i. Spare low temp fan shroud
j. Spare BLTouch bed sensor
k. Spare fuse
l. Spare stepper driver
m. USB thumb drive
n. Tweezers, Pin for clearing nozzle clogs
o. Phillips head screwdriver
p. Purple glue stick
q. Spare blower fan, Masking tape
4. 2 x 1KG rolls of ABS (or ASA)
5. High temp carbon fiber print surface
6. 12 gauge 20 amp power cable
Page | 4
UNPACKING THE PRINTER CONTENTS
1. Remove the RED gantry guard blocks with a Philips head screwdriver before doing anything else.
Failure to do so could damage the printer. These are installed to prevent movement of the
gantry during shipping.
2. Plug in the printer using the supplied power cord. (Usually located on top of the print bed, zip tied
to the back panel).
3. Turn on the printer.
Page | 5
4. Press the “MOVE” icon on the home screen.
5. Press the “HOME ALL” button. This will cause the system to home, and raise the bed so the
contents underneath can be removed.
6. Remove the filament, foam, and toolbag from the printer.
MAKE SURE TO KEEP ALL OF THE PACKAGING FOR 30 DAYS IN CASE THE MACHINE
NEEDS TO BE SENT BACK FOR REPAIR.
Page | 6
MOVING THE PRINTER
Make sure to place the printer on a very sturdy table or work surface to minimize vibrations
during printing.
The rear of the printer must be accessible to load and unload filament, and for safety reasons.
We recommend at least 1 foot behind the printer from any wall.
Work surface must be a minimum of 23” x 25”.
The X400 is a heavy machine, so the work surface should be strong enough to accommodate
150lbs at least.
2 people are required to lift the X400. Do not attempt to move it by yourself!
Any bumps or shocks could throw off the leveling of the bed, gantry, or other parts in the
machine, so lift and set it down carefully.
SETTING UP THE PRINTER
1. Remove the plastic protection film from the side, top, and front door panels.
2. Remove plastic from the touch screen.
Page | 7
3. Connect the ethernet cable to a network port if you want to use the advanced web interface
(Highly recommended). If you don’t have an ethernet plug, and require wifi, you can purchase a
wifi adapter from 3D Labs to connect it to your wireless network. Wifi is not supplied by default
due to ITAR, and security requirements of most businesses.
LOADING MATERIAL
1) Unscrew the ptfe tube coupling on top of the extruder head you intend to use.
Page | 8
2) Unscrew the tension nut so that the spring is fairly loose. Do not loosen it so much that the nut
comes off of the screw.
3) Open the rear door of the printer and feed the material through the tube until about 2” of filament
comes out of the other end inside the printer.
4) Carefully hang the spool onto the mount and close the door.
Page | 9
5) Cut the tip of the filament at a 45-degree angle with flush cutters and insert it into the hole on top
of the extruder head where you removed the coupling.
6) Press down firmly on the filament and insert it about 1” (you may have to press it in a couple of
times) into the hole.
Page | 10
7) Retighten the tension screw on the left a fair amount so that the spring is semi tight. It does not
have to be super tight. Typically, an 1/8-inch (3mm) gap is a good place. Tug on the filament lightly
and you should feel some resistance. This is normal, it means that the extruder is gripping the
filament, which is what we want.
8)
Press the “Material” button on the
touch screen interface.
Tabla de contenidos
