3D Systems Cubify CUBEX Duo Manual de usuario

1

CUBEX

Replacing a

Main Board

PCB

2

Contents

What you will need ..................................................................................................... 3

Removing the Case and floor panel. .......................................................................... 4

Removing the damaged Main Board PCB.................................................................. 6

Fitting the new Main Board PCB ................................................................................ 7

Re attaching the floor panel and case........................................................................ 8

3

What you will need

Replacement Main Board PCB

3mm Hex Driver

2.5mm Hex Driver

4

Before beginning this process please ensure that the print pad is raised to the

top of the machine, all cartridges and the jet wipe have been removed from the

machine and that you have made a note of your Z height and offset settings as

these settings will not be present on the new PCB. Unplug the CubeX from

mains power.

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

5

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

6

Removing the damaged Main Board PCB

Before removing the Main board PCB, label each of the looms that are plugged into

it. The PCB is marked to tell you which loom is plugged into which connector.

Remove the Looms and unplug the power supply from the main board PCB.

Gently pull up on the main board PCB to slide it off of the rubber ties holding it in

place.

7

Using the 2.5mm hex driver, undo the bolts holding the Print Jet driver boards to the

Main Board PCB and remove the Print Jet driver boards. (Note the amount of Print

Jet driver boards will correspond with the amount of Print Jets present on your

CubeX printer)

Fitting the new Main Board PCB

Plug the Extruder Driver boards into the new Main Board PCB and fasten with bolts.

8

Pull the rubber ties up through the holes on the main board PCB to fasten it to the

CubeX.

Plug the looms and power supply back into their corresponding connectors.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

9

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

10

You may now power up your CubeX.

You will need to re activate your CubeX using the activation code associated

with your CubeX. You will also need to re set your Z height and offsets, if you

did not make a note of these settings you can find instructions on how to set

them in the CubeX users guide.

Otros manuales para Cubify CUBEX Duo

3

Tabla de contenidos

Otros manuales de Impresora 3D de 3D Systems

3D Systems

3D Systems ProJet 3500 Max Series Manual de usuario

3D Systems

3D Systems ZPRINTER 650 Manual de usuario

3D Systems

3D Systems CubeX Manual de usuario

3D Systems

3D Systems Cube 3rd Generation Manual de usuario

3D Systems

3D Systems CubePro Manual

3D Systems

3D Systems ProJet 5000 Manual de usuario

3D Systems

3D Systems CubePro Instrucciones de uso

3D Systems

3D Systems SLA 750 Series Manual de usuario

3D Systems

3D Systems ProJet 1200 Manual de usuario

3D Systems

3D Systems ProX 950 Manual de usuario

3D Systems

3D Systems CUBE Manual de usuario

3D Systems

3D Systems CUBE Manual de usuario

3D Systems

3D Systems ZPRINTER 150 Manual de usuario

3D Systems

3D Systems ProJet SLA 6000 Manual de usuario

3D Systems

3D Systems ProX 800 Manual de usuario

3D Systems

3D Systems CUBE Manual del operador

3D Systems

3D Systems Cube 2nd Generation Manual de usuario

3D Systems

3D Systems PROJET 3500 Guía de referencia

3D Systems

3D Systems FabPro 1000 Manual

3D Systems

3D Systems BFB-3000 Manual de usuario

3D Systems

3D Systems CubePro Manual de usuario

3D Systems

3D Systems CubePro Manual de usuario

3D Systems

3D Systems ProX SLS 6100 Manual de usuario

3D Systems

3D Systems ProJet 4500 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario