ZyXEL Communications NWA-8500 Manual de usuario
Copyright © 2007. All rights reserved
NWA-8500
802.11a/g Ultra Thin Wireless Business
Access Point
Quick Start Guide
Version 1.00
6/2007
Edition 1
CONTENTS
ENGLISH 1
DEUTSCH 19
ESPAÑOL 27
FRANÇAIS 35
ITALIANO 43
РУССКИЙ 51
SVENSKA 59
简体中文 65
繁體中文 71
ENGLISH
1
Introduction
The NWA-8500 is an access point that receives power from a
PoE (power over Ethernet) WLAN controller. The NWA-8500
does not require a power adapter or power cord. You can just
deploy the NWA-8500 in your wireless network with a PoE
wireless switch. Through the NWA-8500 (labeled AP in the
following figure), wireless clients on the WLAN can access
the Internet or the wired network.
This guide shows you how to connect the NWA-8500 to a
WLAN controller and hang your NWA-8500 on a wall.
1 Hardware Connections
Follow the steps below to connect your NWA-8500 for
Internet access.
ENGLISH
2
ENGLISH
1Use the included Ethernet cable to connect the
ETHERNET port to a PoE WLAN controller’s WLAN port.
At the time of writing, you can connect only the NWA-8500
to the NXC-8160 model.
1.1 LEDs
Look at the LEDs (lights) on the NWA-8500.
The PWR, LAN, WLAN 1 and WLAN 2 LEDs are all on when
the Ethernet port is properly connected. The LAN, WLAN 1
and WLAN 2 LEDs blink when there is traffic.
ENGLISH
3
VIf none of the LEDs are on, check your
connections, and inspect your cable for
damage. Make sure that your wireless switch is
powered on. If the LEDs are still off, contact
your vendor.
2 Hardware Mounting
In general, the best location for the access point is at the
center of your intended wireless coverage area. For better
performance, mount the NWA-8500 in a place that is high up
and free of obstructions.
2.1 Wall-mounted
Follow the steps to attach your NWA-8500 to a wall.
"See Product Specifications for the size of
screws to use and how far apart to place them.
1Locate a high position on the wall that is free of
obstructions.
2Drill two holes for the screws.
4
ENGLISH
"Be careful to avoid damaging pipes or cables
located inside the wall when drilling holes for the
screws.
3Do not insert the screws all the way into the wall. Leave a
small gap of about 0.5 cm between the heads of the
screws and the wall.
4Make sure the screws are snugly fastened to the wall.
They need to hold the weight of the NWA-8500 with the
connection cables.
5Align the holes on the back of the NWA-8500 with the
screws on the wall. Hang the NWA-8500 on the screws.
Product Specifications
Dimension 198.5 (W) x 138.5 (D) x 47.5 (H) mm
ENGLISH
5
Weight 400 g
Connector One auto-negotiating, auto MDI/MDI-X 10/100
Mbps RJ-45 Ethernet port
Antenna Internal antennas with dual-band support (2.4
GHz and 5 GHz)
Distance between the centers of
the holes (for wall mounting) on
the device’s back.
140 mm
Recommended type of screws for
wall-mounting
M4 Tap Screw (see the
figure below)
Operating
Temperature
0º C ~ 50º C
Operating
Humidity
10% ~ 90% RH (non-condensing)
Approvals EMC: FCC Class B, CE-EMC Class B, C-Tick
Class B, VCCI Class B
Safety: CSA International, CE EN60950-1
6
ENGLISH
The following are dimensions of an M4 tap screw and
masonry plug used for wall mounting. All measurements are
in millimeters (mm).
Certifications
Federal Communications Commission (FCC)
Interference Statement
The device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including
interference that may cause undesired operations.
ENGLISH
7
This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses, and can radiate
radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this device does cause harmful interference to radio/
television reception, which can be determined by turning the
device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
8
ENGLISH
FCC Radiation Exposure Statement
• This transmitter must not be co-located or operating in con-
junction with any other antenna or transmitter.
• For operation within 5.15 ~ 5.25GHz frequency range, it is
restricted to indoor environment.
• IEEE 802.11b or 802.11g operation of this product in the
U.S.A. is firmware-limited to channels 1 through 11.
• To comply with FCC RF exposure compliance requirements,
a separation distance of at least 20 cm must be maintained
between the antenna of this device and all persons.
注意 !
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許
可，公司、商號或使用者均不得擅自變更頻率、加大功率
或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及
干擾合法通信；經發現有干擾現象時，應立即停用，並改
善至無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電信。低功率
射頻電機須忍受合法通信或工業、科學及醫療用電波輻射
性電機設備之干擾。
在 5250MHz~5350MHz 頻帶內操作之無線資訊傳輸設備，
限於室內使用。
ENGLISH
9
Notices
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This device has been designed for the WLAN 2.4 GHz and 5
GHz networks throughout the EC region and Switzerland,
with restrictions in France.
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Viewing Certifications
1Go to http://www.zyxel.com.
2Select your product on the ZyXEL home page to go to that
product's page.
3Select the certification you wish to view from this page.
Safety Warnings
"For your safety, be sure to read and follow all
warning notices and instructions.
Otros manuales para NWA-8500
1
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de ZyXEL Communications
ZyXEL Communications
ZyXEL Communications NWA5121-N Manual de usuario
ZyXEL Communications
ZyXEL Communications PLA4225 Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA 1121-NI - Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA-3100 Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA-3165 Guía de referencia
ZyXEL Communications
ZyXEL Communications NWA-1100 - V1.00 Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA5160N Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA5120 Series Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA1120 Series Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA3550-N - Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA-3165 Guía de referencia
ZyXEL Communications
ZyXEL Communications NWA-1100 Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA-3500 Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA570N Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA5121-N Manual de usuario
ZyXEL Communications
ZyXEL Communications P-2612HW Series Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYAIR G-1000 Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA1300-NJ - Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA3000-N Series Manual de usuario
ZyXEL Communications
ZyXEL Communications NWA5123-AC HD Manual de usuario
