ZKTeco FR1200 Manual de usuario

ZKTecoFR1200UserManual

Version:1.0.1

Date: Dec. 2011

Introduction:

Thisdocumentmainlyintroducestheuser’soperationof ZKTeco FR1200.Aboutthe

deviceinstallation,pleaserefertotheInstallationGuide.

TableofContents

1.UsingInstruction ............................................................................ 1

1.1FingerPlacement .................................................................. 1

1.2InstructionforCardUsing .................................................... 2

1.3Precautions............................................................................ 2

2.DeviceIntroduction ........................................................................ 3

3.DeviceOperations.......................................................................... 6

4Appendix........................................................................................ 11

4.1ListofParameters ............................................................... 11

4.2StatementonHumanRightsandPrivacy ........................... 12

4.3EnvironmentFriendlyUseDescription.............................. 14

1. Using Instruction

 1

1.UsingInstruction

1.1FingerPlacement

Enrollfingerprintbypressingindexfinger,middlefingerorringfinger(thumband

littlefinger areclumsy).

1.Properpress:

2.Improperpress:

Makefingercenterpressedonthe

sensorwindow.

Slant Too low

Upright Toolean

Pleaseadoptthecorrectwaytoplacethefingertoavoidimproperoperation

ledtotheidentificationperformancedegradation.

ZKTeco FR1200UserManualV1.0.1

 2

1.2InstructionforCardUsing

Integrated with a noncontact RF card reader module, this reader supports the ID

cards andMifare cards (Optional and only usedas ID cards). Byoffering multiple

verificationmodessuchasFP,card,FPpluscard,FPorcardverification,thisreader

canaccommodatetodiversifieduserneeds.

Swipe your card across the sensor area following the light and beep prompts and

removeyourcardafterthereaderhassensedit.Forthecardsensorarea,pleaserefer

to 2DeviceIntroduction.

1.3Precautions

Protect the reader from exposure to direct sunlight or strong beam, for the strong

sunlightgreatlyaffectsthefingerprintcollectionandleadstofingerprintverification

failure.

Itisrecommendedtousethereaderunderatemperatureof0–50°Csoastoachieve

theoptimalperformance.Intheeventofexposureofthereadertotheoutdoorsfor

long periods of time, it is recommended to adopt sunshade and heat dissipation

facilities because excessively high or low temperature may slow down the reader

operation and result in high false rejection rate (FRR) and false acceptance rate

(FAR).

Wheninstallingthereader,pleaseconnectthepowercableafteralltheotherwiring.

Ifthereaderdoesnotoperateproperly,besuretoshutdownthepowersupplybefore

performing necessary inspection. Be aware that any liveline working may cause

damagetothereader,andthatdamageisbeyondthescopeofournormalwarranty.

For mattersthat are not covered in this document, pleaserefertorelated materials

includingtheInstallationGuide,FPReaderSoftwareUserManual.

2. DeviceIntroduction

 3

LEDIndicator

FingerprintSensor

CardSensor Area

2.DeviceIntroduction

FR1200, a fingerprint reader with RS485 communication interface works with

biometricaccesscontrollersandfingerprintstandaloneaccesscontrol.Itoffersthe

function of capturing and transferring fingerprint samples to access control panel

insidetomatch.WithitsIP65ratedruggedstructure. Thisreaderoperationissimple

andflexible.Thelightandbeeppromptswillguideyouthroughalltheoperations

without screen display or keyboard. Featuring a compact and simple design, this

readerisanewconceptofinBIOfingerprintreader.

ProductAppearance:

Frontview:

² LEDindicator:TheLEDindicatorisusedtodisplayreaderoperationresults

andexceptionalstatuseswhicharedefinedasfollows:

ZKTeco FR1200UserManualV1.0.1

 4

DipSwitch

WiringTerminal

ResetButton

Operation succeeds: The green indicator issolid on for one second, at the

sametimethespeakerplayonelongbeep.

Operation failed: The redindicatoris solid on for one second, at thesame

timethespeakerplaytwoshortbeep.

Verificationstate:ThegreenLEDblinksonceeverytwosecond,thebeeper

withnosound.

² CardSensorArea:Referstotheareainthereddashedlineasshowninthe

figureabove.

² FingerprintSensor: Usedtoenrollandmatchfingerprints.

Bottomview:

² ResetButton: Usedtorestartthereader.

Backview:

DipSwitch:14switchesareusedtosettheRS485communicationaddress(device

ID).Number5switchisidle.Andthenumber6switchisusedtosettheterminal

2. DeviceIntroduction

 5

resistancestate.

WiringTerminal: Forconnectionterminals.

ZKTeco FR1200UserManualV1.0.1

 6

3.DeviceOperations

Afterthereaderispoweredon,thereadercannotidentifythefingerprintorcard.In

other words, the reader can not receive data or send data without access control

panelconnection.

Only whenthe reader connected withthe access control panel that the reader can

promptifthecardorfingerprintisenrolledornot,andverifytheuseraccordingto

thereturningresultofbackgroundaccesscontrolpanel.

Userverificationoperations:

1.Whenthereaderconnectedwiththeaccesscontrolpanel,itisinverificationstate,

thebeepwithnosound,andthegreenLEDblinkonceeverytwosecondtoprompt

verification.

2. Start user verification. The reader supports four verifications modes: only

fingerprint, only card, fingerprint plus card, fingerprint or card verification. The

process include press fingerprint first or swipe card first, the operation areas the

follows:

Pressfingerprintfirst:

(1) Press your finger on the fingerprint sensor inaproper way. The device beeps

once,andthentheLEDoff,switchtothebackgroundverification.

(2)Theaccesscontrolpaneldetermineswhetherthecontrolorderistimeout.Ifitis

timeout,thedevicebeeps3soundsandtheredLEDsolidon.Otherwise,itwillget

thesystemverificationmodessetting.

Onlyfingerprint/cardorfingerprintverification:Sendthefingerprinttemplateto

the access control panel, and wait for the result. If it is waitingtime out, beep 3

sounds and the red LED solid on. If the reader get the verification result in the

3. DeviceOperations

 7

settingtime,2beepandredLEDsolidonforverificationfailed,1beepandgreen

LEDsolidonforverification succeed.

Card plus fingerprint verification: Determine if there is the card data. If you

swipecardneartothecardreader,thensendthefingerprinttemplateandcarddata

totheaccesscontrolpanel,andwaitfortheresult.Ifitiswaitingtimeout,beep3

sounds and the red LED solid on. If the reader get the verification result in the

settingtime,2beepandredLEDsolidonforverificationfailed,1beepandgreen

LEDsolidonforverificationsucceed.

Onlycardverification:Nosendingofthedatatoaccesscontrolpanel,thedevice

beeps2sounds,andredLEDsolidon.

ZKTeco FR1200UserManualV1.0.1

 8

Theverificationoperationsareasfollows:

ReaderStart

Gettingcontrol

ordertimeout?

OnlyFP

verification？

FPorcard

verification？

FPandcard

verification？

Sendcardnumber

andFPtemplateto

accesscontrolpanel

Prompt:1 beep,

greenLEDon

Verification

resulttimeout？

N

Y

N

GetFPtemplate,1

beep, lightoff,

switchto 485

Onlycard

verification？

Getcardnumber

already?？

Y

SendFPtemplateto

accesscontrolpanel

Passthe

verification?

Prompt:2beeps,

redLEDon

Readerstop

Prompt:3beeps,

greenLEDon

N

YN

N

Y

Otros manuales para FR1200

Tabla de contenidos

Otros manuales de Sistema de seguridad de ZKTeco

ZKTeco

ZKTeco SF1008+ Manual de usuario

ZKTeco

ZKTeco DM10 Manual de usuario

ZKTeco

ZKTeco RF100 Manual de usuario

ZKTeco

ZKTeco ZKX6550 Manual de usuario

ZKTeco

ZKTeco FaceKiosk-H13 Manual de usuario

ZKTeco

ZKTeco G4 Pro Series Manual de usuario

ZKTeco

ZKTeco ZKRF10M Manual de usuario

ZKTeco

ZKTeco SpeedFace Series Manual de usuario

ZKTeco

ZKTeco ProFace X Manual de usuario

ZKTeco

ZKTeco ProBio Manual de usuario

ZKTeco

ZKTeco OP-400 Manual de usuario

ZKTeco

ZKTeco X7 Manual de usuario

ZKTeco

ZKTeco FMD Pro 2.0 Manual de usuario

ZKTeco

ZKTeco FaceDepot-7BL Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario