Zenith HydroTap G5 Manual de usuario

1808081NZ v1.00 03.21 Industrial Tap Instructions

Zenith

HydroTap G5

Tap installation instructions

Industrial Side Touch Tap

Industrial Top Touch Tap

Visit our website to

download the manuals

2 808081NZ v1.00 03.21 Industrial Tap Instructions

Using these instructions

Please refer to all safety and installation requirements detailed in the Quick

start guide provided with the HydroTap Command Centre, and HydroTap

Command Centre installation instructions found online, prior to installation of

or any change to the complete system.

Before commencing the installation,

download & read the HydroTap

Command Centre installation

instructions

Read the

instructions

WARNING

Contents

Before Installation ...................................................................3

Installation: Top Touch Tap (sink)........................................... 4

Installation: Side Touch Tap (sink) ...........................................5

Font Installation (optional)..................................................... 6

Side Touch Tap Template: Buttons on LHS ............................. 8

Side Touch Tap Template: Buttons on RHS............................. 9

USB Connection .....................................................................11

Connect to Command Centre............................................... 12

Commissioning ..................................................................... 13

Tap Operation: Top Touch Tap .............................................. 14

Tap Operation: Side Touch Tap ............................................. 15

3808081NZ v1.00 03.21 Industrial Tap Instructions

Position the tap such that it dispenses into

the sink bowl with clearance for a cup or tea

pot.

Alternatively, refer to pages 8-9 for tap

installation on a Font.

Position Command Centre and Tap as close

together as possible.

BC Compact

Ensure that taps are positioned to minimise

the risks of scalding when dispensing

boiling water.

Tools needed for tap installation

In addition to normal tools, the following (or equivalent) will be required.

• 35mm diameter sheet metal hole punch for sinks.

• 35mm diameter hole saw for worktops.

• Hole saw for font installation (optional - refer to font kit)

• Tube spanner for fixing the tap assembly (supplied).

Water supply pressure requirements

Positioning

Min - Max pressure, kPA (bar)

HydroTap 170 (1.7) - 700 (7.0)

Booster 200 (2.0) - 700 (7.0)

Be aware of the risks of hazards which could

cause harm when using tools. Assess the

risks before starting the installation.

Before Installation

4 808081NZ v1.00 03.21 Industrial Tap Instructions

1Top Touch Tap installation

• Pass the tubes and USB cable through

the Ø35mm hole. Use a tube spanner

to secure the tap in place.

Black

plastic spacer

Fixing

washer

Spider

clamp

Fixing nut

USB

Installation: Top Touch Tap (sink)

• Cut a Ø35mm hole in the worktop /

sink.

• Apply a light smearing of silicone

sealant on the underside of the spacer

to ensure a watertight ﬁt.

Ø35mm

Black

plastic spacer

5808081NZ v1.00 03.21 Industrial Tap Instructions

• Use the template supplied on pages 6-7

to locate and cut the 35mm hole and 3x

6.5mm clearance holes in the correct

orientation for either left or right hand

operation.

• Use 3x cap screws to suit your benchtop

thickness.

• Apply a light smearing of silicone sealant

on the underside of the O-ring seal to

ensure a watertight ﬁt.

• Pass the tubes and USB cable through

the Ø35mm hole.

• From below the bench, feed the three

tubes and USB cable through the clamp

block, noting the orientation marker.

• Fit the 3 cap screws and spring washers.

Tighten with an allen key.

• Use a tube spanner to secure the ﬁxing

nut.

2Side Touch Tap installation

Installation: Side Touch Tap (sink)

Internal nuts

Tapered base

O-ring seal

Benchtop

Clamp block

Spring washer

Fixing nut

Cap screw Benchtop

thickness

M6 x 35 (supplied) 14 - 18 mm

M6 x 30 (not supplied) 8 - 13 mm

M6 x 40 (not supplied) 19 - 24 mm

6 808081NZ v1.00 03.21 Industrial Tap Instructions

1Top Touch Tap Font Installation

Font Installation (optional)

Industrial Top

Touch Tap

Black plastic

spacer

Font

Spacer ring

under Font

Benchtop

Steel washer

Spider clamp

Fixing nut

• Position the Font template (provided

in the kit) on the bench, so that the

Command Centre is within reach of the

tap hoses and USB cable.

• Cut the holes as shown in the template.

• Apply a light smearing of silicone

sealant on the underside of the spacer

under the Font. Locate the spacer

under the Font base.

• Pass the tubes and USB cable through

the hole and use a tube spanner to

secure the tap in place.

• Position the Font template (provided

in the kit) on the bench, so that the

Command Centre is within reach of the

tap hoses and USB cable.

• Cut the holes as shown in the template.

• Apply a light smearing of silicone sealant

on the underside of the spacer under the

Font. Locate the spacer under the Font

base.

• From below the bench, feed the three

tubes and USB cable through the clamp

block, noting the orientation marker.

• Fit the 3 cap screws and spring

washers. Tighten with an allen key.

• Use a tube spanner to secure the fixing nut.

2Side Touch Tap Font installation Industrial Side

Touch Tap -

Tapered base

O-ring seal

Font

Spacer ring

under font

Benchtop

Clamp block

Spring washer

Fixing nut

Cap screws x3

7808081NZ v1.00 03.21 Industrial Tap Instructions

PULL OUT

TEMPLATE FOR

INDUSTRIAL

SIDE TOUCH TAP

INSTALLATION

8 808081NZ v1.00 03.21 Industrial Tap Instructions

Side Touch Tap Template: Buttons on LHS

9808081NZ v1.00 03.21 Industrial Tap Instructions

Side Touch Tap Template: Buttons on RHS

10 808081NZ v1.00 03.21 Industrial Tap Instructions

Prepare the drainage point

• Locate pipe branch attachment

temporarily in position on vertical pipe,

upstream from a drain trap.

• Mark spigot hole position, remove

attachment & drill out 13mm diameter.

• Apply sealant to spigot groove.

• Ensuring spigot is pointing upwards, snap

attachment into place over hole.

• Secure with worm drive clamps.

• Attach drain pipe to spigot.

• Secure with worm drive clamp.

Sealant

groove

Flexible pipe from Font

Pipe branch attachment

Worm drive clamps

Pipe branch

attachment

Position upstream of a drain trap.

Drain pipe must have constant fall.

Ensure there are no kinks or sags.

Secure Font & Tap, attach drain (underneath)

• Secure flexible drain pipe (not supplied) with a

worm drive clamp.

• If required, use an elbow fitting under the Font

to prevent hose kinks.

Mounting

nut &

washer

Flexible

drain pipe

Worm drive clamp

Spider clamp

Fixing washer

Fixing nut

Font Installation (optional)

• Test for leaks and re-seal if

required.

Otros manuales para HydroTap G5

Tabla de contenidos

Otros manuales de Producto de plomería de Zenith

Zenith

Zenith Surgeon 42226NZ Manual de usuario

Zenith

Zenith HydroTap G5 Manual de instrucciones

Zenith

Zenith ChillTap Residential Manual

Zenith

Zenith Miniboil Manual

Zenith

Zenith HydroTap Classic Manual de usuario

Zenith

Zenith HydroTap G4 Manual de usuario

Zenith

Zenith HydroTap G4 Celsius Series Manual de usuario

Zenith

Zenith FlushMaster Solo 42214 Manual de usuario

Zenith

Zenith FlushMaster 40090NZ Manual

Zenith

Zenith HydroTap G5 UltraCare BCU 40 Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario