Zavio B7210 Manual de usuario

Zavio B7210 Quick Installation Guide

Please follow the installation steps below to set up your B7210 Bullet IP Camera.

Check the package contents against the list below. See P.1

Physical overview. See P.2

I/O Terminal Block Pin Definition. See P.3

I/O Terminal Block Circuit. See P.3

LED Indicator Definition. See P.4

Power mode. See P.4

Install the hardware and connect all cables. See P.4

Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.7

Access the IP Camera using Intelligent IP Installer. See P.7

Mac OS using Safari Broswer. See P.9

Lighting environment. See P.10

Change the Web Interface into your preferred language. See P.10

Application of IP Camera. See P.11

For more information, please check the User Manual available in the Software CD or you can download the

latest software from http://www.zavio.com

Package Contents

Camera

B7210 2Megapixel IR Bullet Network

Camera

Quick Installation Guide

rief product information and quick installation

Software CD

IP Surveillance Software

Intelligen

t IP Installer

User Manuals

Language Packs

Accessory

Wall mount bracket &

U-shape bracket

Metal plate for wall mount bracket

Alignment Sticker

Waterproof Connector

Screw pack for sun shield & burglarproof screw

Screw pack for wall and ceiling mounting

Silica gel

Foam tape

2 pin terminal blocks for power

Physical overview

DI / DO

IR LED

Lens

Light Sensor

DC 12V/1.5A

I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

Definition

Description

Max. V/A

Ground

+ 12V DC

12V DC

1.2W

AUDIO_In(+)

Unbalanced, 1.4Vp-p, 1Vrms, terminal block

AUDIO_In(+)

Unbalanced, 1.4Vp-p, 1Vrms, terminal block

Digital Output 1

Uses an NPN transistor with the emitter connected to the GND

pin. If used with an external relay, a diode must be connected in

parallel with the load for protection against voltage transients.

100 mA

24V

Digital Output 2

Uses an NPN transistor with the emitter connected to the GND

pin. If used with an external relay, a diode must be connected in

parallel with the load for protection against voltage transients.

100mA

24V

Digital

Input 1

Connected to GND to activate, or leave floating (or unconnected)

to deactivate.

30V DC

Digital

Input 2

Connected to GND to activate, or

leave floating (or unconnected) to deactivate.

30V DC

Digital Input 1/2: Max: 30V DC

Digital Output 1/2: Max: 24V / 100mA

LED Indicator

ōōņŅ

ńŰŭŰų

ŊůťŪŤŢŵŪŰů

ŏŦŵŸŰųŬ

ňųŦŦů

ŔŵŦŢťźġŨųŦŦůġŧŰųġŏŦŵŸŰųŬġŭŪůŬį

ŐųŢůŨŦ

ŇŭŢŴũġŰųŢůŨŦ

ġŸũŪŭŦġŏŦŵŸŰųŬġŢŤŵŪŷŪŵźġ

őŰŸŦų

œŦť

ŔŵŦŢťźġųŦťġŧŰųġţŰŰŵŪůŨġŶűġűųŰŤŦŴŴ

ŃŭŶŦ

ŔŵŦŢ

ťźġţŭŶŦġŧŰųġţŰŰŵŪůŨġŶűġŤŰŮűŭŦŵŪŰůġ

ŖůŭŪŵġ

ŸũŦůġųŦŴŦŵġţŶŵŵŰůġűųŦŴŴŦť

ŧŰųġŢŵġŭŦŢŴŵġĶġŴŦŤįġ

ŵŰġŧŢŤŵŰųźġťŦŧŢŶŭŵ

ŎŪŤųŰġ

ŔŅġ

İġ

ŔŔŅŉń

ŐųŢůŨŦ

ŔŵŦŢťźġŰųŢůŨŦġŮŦŢůŴġŔŅġŤŢųťġųŦŢťź

ŇŭŢŴũŦŴġŰųŢůŨŦġŸũŪŭŦġŢŤŤŦŴŴŪůŨġŔŅġŤŢųť

Power Mode

PoE Mode

Power

Requirement

őŰņġĩŊņņņĹıĳįĴŢŧĪġŸŪŵũġńŭŢŴŴġĴġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ

ŏŰŵŦ

ĻġŘũŪŭŦġŊœġŰůĭġŉŦŢŵŦųġŢůťġŇŢůġŸŪŭŭġţŦġťŪŴŢţŭŦťį

ġġ

Power

nsumption

ĴįĶĺŘĭġŸŪŵũŰŶŵġŊœİŉŦŢŵŦųİŇŢůġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ

ĸįĺŘĭġŸŪŵũġŮŢŹįġŊœġŰů

Adaptor Mode

Power

Requirement

ĲĳŗİĲįĶłġłťŢűŵŰųġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ

ŏŰŵŦĻġŘũŪŭŦġŊœġŰůĭġŉŦŢŵŦųġŰųġŇŢůġŸŰŶŭťġţŦġŢŤŵŪŷŢŵŦťġŢŶŵŰŮŢŵŪŤŢŭŭźįġ

Power

nsumption

ĴįĶĹŘĭġŸŪŵũŰŶŵġŊœİŉŦŢŵŦųİŇŢůġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ

ĸįĺŘĭġŸŪŵũġŮŢŹįġŊœġŰůġ ġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ

ĺįķŘĭġŸŪŵũġŮŢŹįġŊœġŰůġİġŉŦŢŵŦųġŰůġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġ

ĹįĹĸŘĭġŸŪŵũġŮŢŹįġŊœġŰůġİġŉŦŢŵŦųġŇŢů

Note: Heater will be activated while the inner temparature drops under 5ɗand fan over 50ɗ.

Install the hardware and connect all cables

a. Hardware Installing

1) Assembling sun shield and camera with two supplied screws(M3*6).

2) Fix U-shape bracket to the bottom of camera with supplied screws.

3) Insert all cables (RJ45/power cord/DIDO) into waterproof connector (M25*1.5).

4) Open the front cover and feed all cables through the screw hole of bottom cover from outside. Connect

them to sockets. Then secure the connector tightly.

5) Attach the foam tape and silica gel. (Please change a new silica gel if open the top cover afterwards.)

6) Lock the front cover. Then secure the burglarproof screw.

7) Feed all cables through the front opening of wall mount bracket.

8) Push the spring mortise of wall mount bracket. Then hook the U-shape bracket onto the groove of the

former.

9) Secure the two screws of wall mount bracket on the other side.

b. Wall mounting and Ceiling mounting

1) Attached the alignment sticker to the wall. Drill four holes into the wall, which three for screws and one

for cable. Then hammer the supplied plastic anchors into the screw holes and secure the plate with

supplied screws (T1/4”*32).

2) Hang the wall mount bracket on the plate and fix it with the supplier screw.

3) Adjust the angle of the wall mount bracket to aim the shooting area.

c. Lens Focusing

D. Connect all cables

d1. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Using a standard RJ-45 network cable, connect the IP Camera

to a normal Hub / Switch / Router.

d2. Power over Ethernet (PoE)

Using a standard RJ-45 network cable, connect the IP Camera

to a PoE-enabled Hub / Switch / Router.

Microsoft OS:Use the software CD to install Intelligent IP Installer

Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow these

steps to install the firmware.

Access the IP Camera using Intelligent IP Installer

1. Please check two settings before using Intelligent IP Installer .

Select “Intelligent IP Installer” and follow the installation process to complete the installation.

b. Browser’s Internet Properties

Privacy

ɦUncheck Pop-up Blocker

a. Browser’s Internet Properties

Security

ɦDefault Level

2. Click the Intelligent IP Installer Icon on your desktop. The main page will show up listing all active

camera and video server

devices. Select the relevant IP camera from the list and click Link to IE.

3. Enter your Username and Password

to login

to the IP Camera.

(

Default is admin / admin)

4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar:

This website wants to install the following add

-on: ‘AxvideoView.cab from ‘Zavio Inc’.

5. Click the information bar, and select Install ActiveX control.

6. Click Install.

Mac OS using Safari Browser

7. Live video displays in the centre of your web browser.

1. Select Safari icon

2. Click Bonjour function and select the camera

you wish to access.

4. The monitor image will be displayed in your browser.

. Enter name and password to login to the IP

camera. (

Default is admin / admin)

Otros manuales para B7210

Tabla de contenidos

Otros manuales de Cámara de seguridad de Zavio

Zavio

Zavio B5010 Manual de usuario

Zavio

Zavio D611E Instrucciones de uso

Zavio

Zavio F610A Instrucciones de uso

Zavio

Zavio CF7300 Manual de usuario

Zavio

Zavio D8520 Manual de usuario

Zavio

Zavio F731E 35M Manual de usuario

Zavio

Zavio B8210 Manual de usuario

Zavio

Zavio N6130 Instrucciones de uso

Zavio

Zavio D4320 Manual de usuario

Zavio

Zavio F3101 Manual de usuario

Zavio

Zavio F3100 Manual de usuario

Zavio

Zavio CB5220 Manual de usuario

Zavio

Zavio F312A Manual de usuario

Zavio

Zavio CD3210 Manual de usuario

Zavio

Zavio CB3210 Manual de usuario

Zavio

Zavio M511W Manual de usuario

Zavio

Zavio D-510E-varifocal lens Manual de usuario

Zavio

Zavio B6330 Manual de usuario

Zavio

Zavio CD5220 Manual de usuario

Zavio

Zavio F7220 Manual de usuario

Zavio

Zavio D610A Instrucciones de uso

Zavio

Zavio D6111 Manual del operador

Zavio

Zavio B6110 Manual de usuario

Zavio

Zavio F5110 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario