Zavio P4520 Manual de usuario
1
/ B5210
ZAVIO Fisheye Camera
Quick Installation Guide
2
Quick Installation Guide
Please follow the installation steps below to set up your IP Camera.
Check the package contents with the list below. See P.2
Physical overview. See P.3
I/O Terminal Block Circuit. See P.4
I/O Terminal Block Pin Definition. See P.4
LED Indicator Definition. See P.5
Power mode. See P.5
Installation of hardware and connection of all cables. See P.5
Windows: Go to Zavio website and download Camera Installation Tool. See P.9
Access the IP Camera using Camera Installation Tool. See P.9
MAC OS: using Safari Browser. See P.12
Lighting environment. See P.14
Change language of the web interface. See P.14
Application of IP Camera. See P.15
Package Contents
Camera
IP Camera
Quick Installation Guide
Brief product information and quick installation
Accessory
6 pin cable for DI/DO and audio, 2 pin I/O
terminal block, plastic plate and screw pack for
wall and ceiling mounting, L-type hex key
wrench, alignment sticker, desiccant
Software
The following software and information are available online:
-Video Management Software
-Camera Installation Tool
-User manuals
-Camera Language Packs
You may download the above at http://www.zavio.com/downloads.php or you
may scan the below QR-Code.
To activate Video Management Software, please enter the license key below.
3
Physical overview
Top cover
Ethernet Socket
Lens
MicroSD/SDHC
Reset
Power LED Indicator
Network LED Indicator
External I/O connector
DC 12V/1A
Routing hole
4
I/O Terminal Block Circuit
I/O Terminal Block Pin Definition
This Camera provides a 6pin cable for external I/O which is used to connect input/
output devices. The pin definitions are described below.
PIN
Definition
Description
Max. V/A
Black
Ground
-
Brown
+ 12V DC
12V DC
1.2W
Red
Audio Input
Connect the wires of the audio input device
to GND (Pin 1) and AUDIO.IN (Pin 3).
-
Orange
Audio Output
Connect the wires of the audio output
device to GND (Pin 1) and AUDIO.OUT (Pin
4).
-
Yellow
Digital
Output 1
Uses an NPN transistor with the emitter
connected to the GND pin. If used with an
external relay, a diode must be connected in
parallel with the load for protection against
voltage transients.
100 mA
24V
Green
Digital Input
1
Connected to GND to activate, or leave
floating (or unconnected) to deactivate.
30V DC
5
LED Indicator Definition
LED
Color
Indication
Network
Blue
Flash blue while Network activity.
Power
Red
Steady red for booting up process
Blue
Steady blue for booting up completion
Purple
Flash purple during firmware upgrading; when reset button pressed for
at least 5 sec. to factory default
Unlit
When you press reset button; or Power off
Reset: Press the button to reboot or hold for 10 sec to restore back to factory default.
Reset process: Press reset button until indicator Unlitsteady red (booting up
process)steady blue (booting up completion)
Reset to default process: Press until indicator steady bluesteady red (booting up
process)steady blue (booting up completion)
Power Mode
PoE Mode
Power Requirement
PoE (IEEE802.3af) with Class 3
Power Consumption
4.19W
Adaptor
Mode
Power Requirement
12V/1A Adaptor
Power Consumption
4.24W
Install the hardware and connect all cables
A. Hardware Installation
1) Loosen the tamper-proof screws using supplied L-type Hex Key Wrench
2) Remove the dome cover. Be careful do not scratch the cover glass.
3) If you want to route cable from the side of camera, please see below figure.
1. Attached the alignment sticker to the wall/ceiling. Drill three holes into the wall,
two for screws and one for cable.
2. Align the two holes on the base of plastic plate with the two plastic anchors on the
wall or ceiling, insert the supplied screws to the corresponding hole and fix them.
3. Secure the camera to the plastic plate with screws(M2.5x6 * 2pcs)
4. Adjust the angle of camera to aim the shooting area.
(for F3105)
6
B. Wall mount L-type Bracket installation(optional)
1. Position the L-type at the desired installation location. Drill two holes into the
placement and hammer the included screw anchors.
2. Align the two holes on the L-type bracket to the two plastic anchors on the wall or
ceiling, insert the supplied screws to the corresponding hole and fix them.
3. Secure the plastic plate to the L-type bracket with screws(M4x10 * 2pcs)
4. Secure the camera to the plastic plate with screws(M2.5x6 * 2pcs)
5. Adjust the angle of camera to aim the shooting area.
7
C. Wall mounting and Ceiling mounting
1) Attached the alignment sticker to the wall/ceiling. Drill three holes into the wall,
which two for screws and one for cable.
2) Hammer the supplied plastic anchors into the holes.
3) Align the two holes on the base of camera with the two plastic anchors on the wall or
ceiling, insert the supplied screws to the corresponding hole and screw them.
8
D. Wall mounting and Ceiling mounting
1. Without Power over Ethernet (PoE) connection
1. Connect the power adaptor to the IP Camera.
2. Connect the IP Camera to a normal Hub / Switch / Router.
2. Power over Ethernet (PoE)
1. Connect the IP Camera to a PoE-enabled Hub / Switch / Router.
Note:
If using a non-PoE switch, please use a PoE power injector to connect the camera.
9
Windows: Go to Zavio Website and download Camera Installation Tool
Please go http://www.zavio.com/softwaredownloads.php download “Camera
Installation Tool”. And follow the installation process to complete the installation.
Access the IP Camera using Camera Installation Tool
1. Please check two settings before using Camera Installation Tool.
a. Browser’s Internet Properties →Security→Default Level
10
b. Browser’s Internet Properties →Privacy →Uncheck Pop-up Blocker
2. Click the Camera Installation Tool Icon on your desktop. The main page will show
up listing all active camera and video server devices. Select the desired IP
cameras from the list and click Link to IE.
Otros manuales para P4520
1
Tabla de contenidos
Otros manuales de Cámara IP de Zavio
Zavio
Zavio N6031 Manual de usuario
Zavio
Zavio D5113 Manual del operador
Zavio
Zavio D7210 Manual de usuario
Zavio
Zavio F3101 Manual de usuario
Zavio
Zavio F7220 Manual de usuario
Zavio
Zavio B52010 Manual de usuario
Zavio
Zavio F312A Instrucciones de uso
Zavio
Zavio F5100 Manual de usuario
Zavio
Zavio P5110 Manual de usuario
Zavio
Zavio D-6210 Manual de usuario
Zavio
Zavio M510E Manual de usuario
Zavio
Zavio P5111 Manual de usuario
Zavio
Zavio F210A Instrucciones de uso
Zavio
Zavio D510E Manual de usuario
Zavio
Zavio F511w Manual de usuario
Zavio
Zavio F1100 Manual de usuario
Zavio
Zavio F611E Manual de usuario
Zavio
Zavio M511W Instrucciones de uso
Zavio
Zavio F312A Instrucciones de uso
Zavio
Zavio F7210 Manual de usuario
