ZALMAN CNPS7000B-AlCu Manual de usuario

* Applies to all versions of CNPS7000B LED.

* Please read before installation.

http://www.zalman.co.kr http://www.zalmanusa.com

CNPS7000B

Intel Pentium 4

Socket 478 CPU

Socket 775 CPU (ZM-CS1 separate

purchase necessary)

AMD Duron/Athlon/Athlon XP/Sempron

Socket 462 CPU

AMD Sempron/AMD64 (Athlon 64/Opteron)

Socket 754/939/940 CPU

User

’’

s Manual

(English version)

User

’’

s Manual

1) Does not generate noise or vibration in Silent Mode.

2) Pure copper and/or pure aluminum base materials ensure excellent heat dissipation.

3) Intel Pentium (Socket 78), AMD Duron / Athlon / Athlon XP / Sempron (Socket 62), and Sempron /

AMD6 (Socket 75 /939/9 0) compatible design for broad compatibility. (To use this product on

socket 775, ZM-CS1 must be purchased separately.)

) 92mm fan inside the FHS maximizes airflow and makes installation easier.

5) The high intensity blue LEDs on CNPS7000B LED coolers stay bright even in Silent Mode.

6) Adjustable fan speed controller (FAM MATE 2) enables control of noise and fan performance.

2) Fan

- Bearing Type : 2-Ball

- Rotation Speed : 1,350 ~ 1,800rpm 10 % (Silent Mode)

1,800 ~ 2,600rpm 10 % (Low-noise Mode)

- Noise Level : 18 ~ 21dB 10% (Silent Mode) - measured at 1m distance from noise source

21 ~ 27.5dB 10% (Low-noise Mode) - measured at 1m distance from noise source

3) FAN MATE 2

- Output Voltage : 5V ~ 11V 2 %

- Allowable Power : 6W or lower

Note 1)

The maximum weight for a cooler is specified as 50g for Intel Socket 78/775 and AMD Socket 75 /939/9 0

and 300g for AMD Socket 62. Special care should be taken when moving a computer equipped with a

cooler which exceeds the relevant weight limit. Zalman is not responsible for any damage that occurs when

moving a computer.

1) Flower Heats nk (FHS)

CNPS7000B-AlCu CNPS7000B-Cu

Model

Spec.

Weight (g)

T.R.

(°C/W )

Silent Mode

Normal Mode

438(1)

0.29

0.22

109 (L) X 109 (W) X 62 (H)

3,154

755(1)

0.27

0.20

Dimensions

(mm)

Dissipation Area

(

㎠

)

※

The specifications of any product may change without prior notice to improve performance.

1. Features

. Exploded View

2. Specifications

Fan

Clip

Fan Support

Fan Fixing Screw

Bolt

Fan Support Fixing Screw

FHS

※

The specifications of any product may change without prior notice to improve performance.

󳣍Korean Patent Application No. 00-5 635

󳣍Korean Design Applications Nos. 02-17 70, 02-25208, 02-25209 etc.

󳣍Patent Applications pending in over 20 nations around the world, including USA, EU, and Japan

4. Patents

1) Common Components

❶

FHS Assembly (CNPS7000B-AlCu/Cu)

❷

Four ( ) Bolts (for installing the FHS)

❸

Thermal Grease

❹

Fan Speed Controller (FAN MATE 2)

❺

Double - sided Tape (for installing FAN MATE 2)

❻

Cable for FAN MATE 2

❼

User’s Manual (in English and Korean)

❶

❽

❾

❿

󱆎󱆏

❷

❹

❸

❺

❼

❻

5. Components

2) Components for Intel Pentium (Socket 78)

❽

Two (2) Clip Supports For Socket 78

Components for AMD Duron / Athlon / Athlon XP /

Sempron (Socket 62)

❾

One (1) A-Type (blue) Clip Support for Socket 62

❿

One (1) B-Type (white) Clip Support for Socket 62

󱆌

Four ( ) Bolts (for fastening the Clip Supports)

󱆍

One (1) set of Washers

)

Components for AMD Sempron / AMD6 (Socket 75 /939/9 0)

󱆎

Two (2) Nipples

󱆏

One (1) Backplate for AMD6

󱆐

Small washers (from component

󱆍

)

󱆌

Precautions

1) If excessive force is exerted on the fan, it may malfunction and result in damage to the product and/or the computer.

2) Do not put your finger in the fan while it is running.

3) Keep the product away from children.

) Check the components list and condition of the product before installing. If there is any problem, contact the shop

where you purchased it and get a replacement or refund.

5) The exposed core of a Socket 62 CPU can be cracked if proper care is not taken. Read the “Installation” section

thoroughly before installing.

NOTICE) Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not

limited to, improper use, problems with electrical power, accident, neglect, alteration, repair,

improper installation, or improper testing.

󱆍󱆐

※

The specifications of any product may change without prior notice to improve performance.

1) Intel Pent um 4 - Socket 478/775

All CPUs conforming to Socket 78 & all CPUs conforming to Socket 775 up to model 5 0

Notes)

3. GHz Northwood, Prescott- 78 of 2.8A/E GHz or higher, and Prescott-775 of up to model 5 0 generate

exorbitant amount of heat (8 W ~ 103W). Refer to the table below and adjust the fan speed so that the

CPU-Case temperature (T

) is lower than the maximum CPU-Case temperature (T

C_MAX

※

Hardware monitoring programs report CPU-Die

temperature (T

) as the CPU temperature.

CPU-Die temperature (T

) is measured about

~ 10℃higher than CPU-Case temperature (T

)

depending on the motherboard and/or BIOS.

Refer to the Zalman website for more information.

※

To use this product on Socket 775, ZM-CS1 (clip support for Socket 775) must be purchased separately.

6. Compatible CPUs

Cautions )

①For Socket 78, as shown in Figure 2, a motherboard that is not compliant with the“10.2mm Motherboard

component height restriction”standard, introduced by Intel, may create interference between

components and the clip. Please do not install the CNPS7000B if this interference is observed.

②No motherboard components with a height greater than 39mm, as well as the PSU, disk drives, VGA card,

and RAM should be present within a 55 mm radius from the center of the CPU.

③For more information, please visit the Zalman website and click on“Compatibility between CNPS7000(A/B)

and Socket 78 Pentium Motherboards”

link.

2) AMD Duron / Athlon / Athlon XP / Sempron - Socket 462

All CPUs conforming to Socket 62 platform

Cautions )

①This product requires “Heatsink Attach Holes”around the

CPU socket as shown on the right.

②No motherboard components with a height greater than 39mm, as well

as the PSU, disk drives, VGA card, and RAM should be present within a

55 mm radius from the center of the CPU.

③

This product cannot be installed if any motherboard component

(usually

capacitor) taller than 15mm is located under the clip.

④For more information, please visit the Zalman website

and refer to

“CNPS7000A/B Compatible Socket 62 Motherboards List”

link.

IHS

CPU Die T

> T

10.2mm Motherboard component height restriction

F gure 1

Compat ble

F gure 2

Not Compat ble

4mm

Clip

Motherboard

Component

Clip

Motherboard Component

②

①

③

Northwood

3.4

68 69.1

2.8A/E, 3.0E 3.2E, 3.4E 520, 530, 540

Prescott - 478 Prescott - 775

CPU

C_MAX

73.2 67.7

℃℃℃℃

※

The specifications of any product may change without prior notice to improve performance.

3) AMD Sempron / AMD64 - Socket 754/939/940

All CPUs conforming to Socket 75 /939/9 0 platform

Cautions )

①No motherboard components with a height greater than 39mm, as

well as the PSU, disk drives, VGA card, and RAM should be present

within a 55mm radius from the center of the CPU.

②For more information, please visit the Zalman website and refer to

“CNPS7000(A/B) Compatible Socket 75 /939/9 0 Motherboards

List”

link.

1) Apply Thermal Grease

Clean off particles and residue then spread a thin layer of

thermal grease on the CPU.

2) Install Cl p Supports for Socket 478

Install the clip supports for socket 78 on both sides of

the retention guide as shown in the diagram.

3) Insert Bolts

Insert the two bolts into the inner holes of the clip.

4) Place FHS

Set the FHS at the center of the CPU. Screw the bolts in

slightly, then tighten each bolt a few turns at a time while

alternating between the two until the clip supports are

completely pressed against the clip.

7. Installation (Intel Pentium 4 - 478)

5) Connect Power (How to use FAN MATE 2)

◆

Please refer to FAN MATE 2 Installation and Usage on page 7.

FHS

Clip Support for

Socket 78

Bolt

Inner Hole

Clip

Retention Guide

Clip Support for Socket 78

󳦈

󳦇

󳦊

CPU (IHS)

Thermal Grease

①

※

The specifications of any product may change without prior notice to improve performance.

1) Install Cl p Supports for Socket 462

Install the clip supports for socket 62 on the motherboard. Make sure to place A-type (blue : nstalled

near the lever) and B-type (wh te) supports at the appropr ate locat on.

The installation should be done in the order of : bolts > small washers > motherboard > small washers >

clip supports (see below).

2) Apply Thermal Grease

Clean off particles and residue then spread a thin layer

of thermal grease on the CPU core (only on the chip's

surface that makes contact with the FHS base).

8. Installation (AMD Duron / Athlon / Athlon XP / Sempron - 462)

5) Connect Power (How to use FAN MATE 2)

◆

Please refer to FAN MATE 2 Installation and Usage on page 7.

3) Insert Bolts

Insert the two bolts into the inner holes of the clip.

4) Place FHS

Set the FHS at the center of the CPU. Screw the

bolts in slightly, then tighten each bolt a few turns at a time

while alternating between the two until the clip supports

are completely pressed against the clip.

FHS

Clip Support for

Socket 62

Bolt

Inner Hole

Clip

CPU

Thermal Grease

Clip Support B for Socket 62 (White)

Lever

Small Washer

Motherboard

Small Washer

Bolt

Clip Support B for Socket 62 (White)

Clip Support A for

Socket 62 (Blue)

※

The specifications of any product may change without prior notice to improve performance.

1) Fasten N pples

Place a small washer on the motherboard. Then, put a nipple over it and fasten the nipple until the

Backplate for AMD6 is firmly attached to the motherboard on the opposite side of the CPU.

* A Retention Guide is not necessary for installing CNPS7000B on Socket 75 /939/9 0.

3) Insert Bolts

Insert the two bolts into the outer holes of the clip.

4) Place FHS

Set the FHS at the center of the CPU. Screw the

bolts in slightly, then tighten each bolt a few turns at a

time while alternating between the two until the nipples

are completely pressed against the clip.

9. Installation (AMD Sempron / AMD64 - 754/9 9/940)

5) Connect Power (How to use FAN MATE 2)

◆

Please refer to FAN MATE 2 Installation and Usage on page 7.

2) Apply Thermal Grease

Clean off particles and residue then spread a thin layer of

thermal grease on the CPU.

FHS

Nipple

Bolt

Outer Hole

Clip

CPU (Lid)

Thermal Grease

Backplate for AMD6

Nipple

Motherboard

Small Washer

※

The specifications of any product may change without prior notice to improve performance.

1) Installing FAN MATE 2 on the Inside of the System 2) Installing FAN MATE 2 on the Outside of the System

※FAN MATE 2 Installation and Usage

11. Thermal Resistance (℃/W) & Noise (dB) Curve

Connect the appropriate 3-pin connector on the

cable to the motherboard fan header and the

CNPS7000B’s fan connector.

Pull the 6-pin connector out of the system through

the back and connect it to FAN MATE 2, which

should be installed on the case using the included

double-sided tape.

◆

When the speed control knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Silent Mode.

Turned fully clockwise, it operates in Normal Mode. You can select the desired fan speed by turning the knob.

Note) FAN MATE 2 has been specifically designed for the fan of this product. Zalman Tech Co., Ltd. is not

responsible for any damage to systems or CPUs caused by using it with other types of fans.

10. Notes on Usage

1) Check ng CPU Compat b l ty

Please refer to “Compatible CPUs” on page 3 to confirm that your CPU is compatible before using the CPU cooler.

2) Caut ons Dur ng Boot ng

When booting the computer, it may automatically power down after an alarm sound by a system

monitoring program to indicate that the CPU fan is rotating slowly. If this happens, turn the speed

control knob fully clockwise to increase the fan speed. Then set ‘CPU Fan Detected’ to ‘Disabled’ in the

BIOS settings, or set the slowest rotational speed of the CPU fan in the system monitoring program to

less than or equal to 1,300rpm.

Note) Some motherboards do not boot if the rotational speed of the CPU fan is below a certain

rpm. If the BIOS settings are updated, Silent Mode can be used. For more information on

updating your BIOS, please refer to your motherboard manufacturer's website. Disabling

CPU fan speed detection in BIOS settings does not affect computer performance.

3) Overclock ng

The fan should be set to Normal Mode if Overclocking.

(Zalman Tech Co., Ltd. is not responsible for any damage resulting from CPU Overclocking.)

Fan Connector

(CNPS7000B)

Motherboard

Double-sided Tape

FAN MATE 2

6-Pin Connector

※

The specifications of any product may change without prior notice to improve performance.

When building a noiseless computer, use Zalman’s Noiseless Power Supply, Fanless Northbridge Cooler,

Heatpipe HDD Cooler, Noiseless Case Fan, Heatpipe VGA Cooler, and Fan Controller for stable performance

and maintain a noiseless environment.

12. Zalman Noise Prevention System

Noiseless Power Supply Fanless Northbridge Cooler Heatpipe HDD Cooler

Noiseless Case Fan Heatpipe VGA Cooler Fan Controller

The TNN 500AF is the world's first absolutely no seless, ant -dust computer case for high-end systems that

has been developed with Heatpipe Technology, HSC (Heat Source Contact) Power Technology, High

Capacity Extrusion Technique, and FMS (Flexible Mounting Structure) Design Technology by ZALMAN

Tech Co., Ltd.

The TNN 500AF package includes a high performance aluminum computer case with an absolutely

noiseless cooling solution that does not require the use of a fan, making it ideal for:

1. D g tal Aud o Workstat ons (DAW) in broadcasting, recording, and postproduction studio control rooms.

2. Mult Med a & Storage Servers for offices, educational facilities, and hotels.

3. Home Theater and Mult Med a Systems for living rooms.

4. H gh Performance No seless Workstat ons & Servers for SOHO (Small Office Home Office) systems.

For more information, please visit the Zalman website.

1 . TNN (Totally No Noise) Computer Case

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de ZALMAN

ZALMAN

ZALMAN ZM80C Manual de usuario

ZALMAN

ZALMAN Optima CNPS8X Manual de usuario

ZALMAN

ZALMAN ZM-RF1 Manual de usuario

ZALMAN

ZALMAN CNPS2X Manual de usuario

ZALMAN

ZALMAN CNPS7000B Series Manual de usuario

ZALMAN

ZALMAN CNPS9800 MAX Manual de usuario

ZALMAN

ZALMAN CNPS9500 AT Manual de usuario

ZALMAN

ZALMAN ZM-WB5 Plus Manual de usuario

ZALMAN

ZALMAN CNPS8000A Manual de usuario

ZALMAN

ZALMAN RESERATOR2 Guía de inicio rápido

ZALMAN

ZALMAN RESERATOR1 V2 Guía de inicio rápido

ZALMAN

ZALMAN ZM-GWB2 Manual de usuario

ZALMAN

ZALMAN CNPS20X Manual de usuario

ZALMAN

ZALMAN CNPS16X Manual de usuario

ZALMAN

ZALMAN Z8 Manual de usuario

ZALMAN

ZALMAN ZM-2HC2 Manual de usuario

ZALMAN

ZALMAN CNPS6500B-AlCu Manual de usuario

ZALMAN

ZALMAN CNPS12X Manual de usuario

ZALMAN

ZALMAN CNPS7000A Series Manual de usuario

ZALMAN

ZALMAN ZM80C-HP Manual de usuario

ZALMAN

ZALMAN VF2000 LED Manual de usuario

ZALMAN

ZALMAN CNPS9X OPTIMA Manual de usuario

ZALMAN

ZALMAN CNPS10X Optima (2011) Manual de usuario

ZALMAN

ZALMAN Extreme Gaming VGA Cooler GV1000 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario