Z GRILLS ZPG-450A Manual de usuario
VN08012019
WOOD PELLET GRILLS
ZPG-450A
OWNER’S MANUAL
MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME
SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS
EMAIL: support@zgrills.com
WEBSITE: www.zgrills.com
1
CONTENTS
WARNINGS
3
COMPONENT LIST
4
ASSEMBLY INSTRUCTIONS
5
INITIAL FIRING INSTRUCTIONS
12
SUBSEQUENT START-UP
13
OPERATING TIPS
14
MAINTENANCE & CLEANING
15
TROUBLESHOOTING
17
DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM
19
Z GRILLS SUPPORT
20
3-Y LIMITED WARRANTY
21
2
SAVE THIS MANUAL FOR FUTURE REFERENCE
3
WARNINGS!
This grill is for outdoor use only. DO NOT use it in any enclosed area.
DO NOT store or use combustible materials or liquids near this appliance.
Keep children away while it is in use.
Maintain a safe distance between your grill and any combustible materials.
DO NOT move your grill while operating or while it is hot. Wait until the grill is
completely cold.
If a grease fire occurs, turn “off”and leave lid closed until the fire is extinguished. DO
NOT unplug the power cord. DO NOT throw water on it. DO NOT try to smother the
fire.
Clean and maintain your grill after each use.
We suggest that you use Z GRILLS BBQ WOOD PELLETS, which are specifically
made to work in our grills.
DO NOT use your grill on rainy days.
DO NOT touch any part of your grill while it is hot. Serious bodily injury could result.
We suggest the use of heat-resistant gloves when operating this grill.
We suggest that you should wrap the Grease Drain Pan with heavy-duty aluminum
foil before using because it is easy to clean.
For convenient and safe assembly, use at least two people to assemble the grill.
Make sure the power cord is disconnected before performing any service or
maintenance.
Always keep the Pellet Hopper dry, the wood pellets will expand greatly, break apart
and even jam the feed system if the pellets get wet or are exposed to high humidity.
DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard.
4
COMPONENT LIST
ITEM
QTY
DESCRIPTION
ITEM
QTY
DESCRIPTION
1
2
Hinge Assembly
31
1
Grease Drain Pan
2
2
Pin
32
1
Porcelain Grills
3
1
Fan
33
1
Warming Rack
4
1
Lid
34
1
Hopper Bottom Cover
5
1
Name Plate
35
1
Hopper Guard
6
1
Lid Handle
36
1
Hopper Shell
7
1
Grill Chamber Assembly
37
1
Cable Box
8
1
Hopper Assembly
38
1
Power Cord
9
1
Chimney Cap Assembly
39
1
Digital Control
10
1
Smoke Stack Assembly
40
1
Auger Drive Motor
11
1
Smoke Stack Gasket
41
1
Auger Nylon Ring
12
1
RTD Temperature Probe
42
1
Auger
13
1
Foot Pad
43
1
Hopper Handle
14
1
Front Shelf Left Bracket
44
1
Hopper Lid
15
1
Hot Rod (Ignitor)
45
1
Insulation
16
1
Feeder Assembly
46
1
Heat Insulation Foam
17
1
Front Shelf Right Bracket
A
4
Hexagon Bolt
18
1
Front Table
B
36
Bolt
19
1
Grease Bucket
C
4
Step Screw
20
2
Leg A
D
4
Cap Nut
21
2
Leg B
E
28
Spring Washer
22
1
Side Table
F
2
Bolt
23
1
Cable Clip
G
4
Flat Gasket
24
1
Hopper Lid Handle
H
2
Nut
25
2
Wheels
I
2
Flat Gasket
26
1
Firepot Welding Assembly
J
24
Flat Gasket
27
2
Axle Bolt
K
1
Screwdriver
28
1
Wheeled Leg Base
L
2
Wrench
29
1
Footed Leg Base
M
2
Cap Nut
30
1
Heat Baffle
Remarks: 46*(Screw package) has 25 screws in total, including 24 necessary screws and 1
spare part screw.
5
ASSEMBLY INSTRUCTIONS
PARTS DIAGRAM
6
Hopper Burner Assembly:
BODY FRAME ASSEMBLY:
1. Attach 2pcs Leg A B (20) (21) to the Leg Base (28) (29) with Bolt (B), Spring Washers (E),
Flat Gasket (J) orderly.
2. Insert Axle Bolt (27) through the hole in Wheel (25) and Wheeled Leg Base (28).
3. Place Washer Gasket (I) onto Axle Bolt (27) and secure with Cap Nut (M). Tighten with
Wrench (L).
7
1.MOUNTING THE BODY FRAME TO THE CHAMBER:
Turn the Grill Chamber Assembly(7) over, attach the Wheeled Leg Assembly and the
Footed Leg Assembly using Bolts(B), Spring Washers(E), Washer Gaskets(J) as shown.
Use the Screwdriver(K) to tighten.
2.INSTALLING CHAMBER HANDLE TO LID:
1. With the Lid (4) open, insert 2 Hexagon Bolts( A) through Flat Gaskets (G) and Lid (4)
and into Lift Handle (6).
2. Using Wrench (L) tighten Hexagon Bolts (A). Be careful not to over tighten Bolts (A).
8
3.ATTACHING HOPPER HANDLE TO HOPPER LID:
Keep the Hopper Burner Lid (44) open. Penetrate the Bolt (F) into the hole on the Hopper
Burner Lid (44), then install the Hopper Lid Handle (24) by screwdriver.
4.ATTACHING THE SMOKESTACK AND CHIMNEY CAP:
Place Bolt (A) through the holes of Smokestack (10) and the holes of Smokestack Insulation
(11), attach two Bolts (A), then attach Washer Gasket (G) and Nuts (H), using the Wrench to
tighten them.
Otros manuales para ZPG-450A
4
Tabla de contenidos
Otros manuales de Parrilla de Z GRILLS
Z GRILLS
Z GRILLS Feed Life ZPG-700E Series Manual de usuario
Z GRILLS
Z GRILLS ZPG-700D2 Manual de usuario
Z GRILLS
Z GRILLS ZPG-700D3 Manual de usuario
Z GRILLS
Z GRILLS 450A Manual de usuario
Z GRILLS
Z GRILLS ZPG-7002F Manual de usuario
Z GRILLS
Z GRILLS ZPG-550B2 Manual de usuario
Z GRILLS
Z GRILLS ZPG-L6002B Manual de usuario
Z GRILLS
Z GRILLS Feed Life ZPG-700E Series Manual de usuario
Z GRILLS
Z GRILLS ZPG-L600D Manual de usuario
Z GRILLS
Z GRILLS ZPG-7002E Manual de usuario
Z GRILLS
Z GRILLS ZPG-6002B3 Manual de usuario
Z GRILLS
Z GRILLS ZPG-450B Manual de usuario
Z GRILLS
Z GRILLS Feed Life ZPG-700E-XL Manual de usuario
Z GRILLS
Z GRILLS ZPG-550B Manual de usuario
Z GRILLS
Z GRILLS ZPG-550B Manual de usuario
Z GRILLS
Z GRILLS ZPG-550C Manual de usuario
Z GRILLS
Z GRILLS ZPG-7002B Manual de usuario
Z GRILLS
Z GRILLS Feed Life ZPG-700E Series Manual de usuario
Z GRILLS
Z GRILLS ZPG-5502H Manual de usuario
Z GRILLS
Z GRILLS ZPG - 50B Manual de usuario
