Yetter SCREW ADJUST Manual de usuario

SCREW ADJUST

RESIDUE MANAGER

OPERATOR’S MANUAL

PARTS IDENTIFICATION

2565-729_REV_J • 06/2021

YETTER MANUFACTURING CO.

FOUNDED 1930

Colchester, IL 62326-0358

Toll free: 800/447-5777

309/776-3222 (Fax)

Website: www.yetterco.com

E-mail: info@yetterco.com

FOREWORD

You’ve just joined an exclusive but rapidly

growing club.

For our part, we want to welcome you to the

group and thank you for buying a Yetter product.

We hope your new Yetter products will help you

achieve both goals-increase your productivity and

increase your efficiency so that you may generate

more profit.

This operator’s manual has been designed into

four major sections: Foreword, Safety

Precautions, Installation Instructions and Parts

Breakdown.

This SAFETY ALERT SYMBOL

indicates important safety

messages in the manual. When you see this

symbol, be alert to the possibility of PERSONAL

INJURY and carefully read the message that

follows.

The word NOTE is used to convey information

that is out of context with the manual text. It

contains special information such as

specifications, techniques and reference

information of a supplementary nature.

The word IMPORTANT is used in the text when

immediate damage will occur to the machine due

to improper technique or operation. Important will

apply to the same information as specified by

note only of an immediate and urgent nature.

It is the responsibility of the user to read the

operator’s manual and comply with the safe and

correct operating procedure and to lubricate and

maintain the product according to the

maintenance schedule in the operator’s manual.

The user is responsible for inspecting his

machine and for having parts repaired or

replaced when continued use of the product

would cause damage or excessive wear to the

other parts.

It is the user’s responsibility to deliver his

machine to the Yetter dealer who sold him the

product for service or replacement of defective

parts, which are covered by the warranty policy.

If you are unable to understand or follow the

instructions provided in this publication, consult

your local Yetter dealer or contact:

YETTER MANUFACTURING CO.

309/776-4111

800/447-5777

309/776-3222 (FAX)

Website: www.yetterco.com

E-mail: [email protected]

WARRANTY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This

warranty being expressly limited to replacement at the factory of such parts or products as shall appear to

be defective after inspection. This warranty does not obligate the Company to bear cost of labor in

replacement of parts. It is the policy of the Company to make improvements without incurring obligations to

add them to any unit already sold. No warranty is made or authorized to be made, other than herein set

forth. This warranty is in effect for one year after purchase.

DEALER: ________________________________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damages to

equipment on which mounted.

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.

WARNING: Denotes a specific potential hazard.

DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study

these precautions carefully and insist that those working with you and for you follow them.

Finally, remember this: an accident is usually caused by

someone’s carelessness, neglect or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always lower or block the implement before

performing service.

If the machine must be serviced in the raised position, jack or block it up to prevent it from accidentally

falling and injuring someone.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough

to cause tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment

to do the same.

Be familiar with all tractor and implement controls and be

prepared to stop engine and implements quickly in an

emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices.

Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

TABLE OF CONTENTS

Forward…..………………………………………………………….……. 2

Warranty……………………………….…………………………….……..2

Safety Information………………………………………………….……...3

Table of Contents………………………………………………….………4

Bolt Torque………………………………………………………….……...5

Planter Adjustments……………………………………………………….6-8

Installations Instructions..…………….…….……………………….……9-11

Maintenance……………………………………………………………...12-13

Parts Identification………………………………..……………..………14-31

BOLT TORQUE

Mounting bolts and hardware

Before operating the Residue Manager for the first time, check to be sure that all

hardware is tight. Check all hardware again after approximately 50 hours of operation

and at the beginning of each planting season.

All hardware used on the Residue Manager is Grade 5 unless otherwise noted. Grade 5

cap screws are marked with three radial lines on the head. If hardware must be replaced,

be sure to replace it with hardware of equal size, strength and thread type. Refer to the

torque values chart when tightening hardware.

Important: Over tightening hardware can cause as much damage as when

under tightening. Tightening hardware beyond the recommended range can

reduce its shock load capacity.

The chart below is a guide for proper torque. Use it unless a specified torque is called out

elsewhere in the manual.

Torque is the force you apply to the wrench handle or the cheater bar, times the length of the

handle or bar.

Use a torque wrench whenever possible.

The following table shows torque in ft. lbs. for coarse thread hardware.

Lubricate all bearings and moving parts as assembled and make certain that they work freely.

WARNING: Never work around the toolbar/implement while in a raised position without using

safety lockups.

CAUTION: The Residue Managers are very heavy and sharp. Pay extra attention to lifting

techniques while handling and or maneuvering the opener during assembly. Failure to do so may

lead to personal injury.

OPERATION PRECAUTIONS

STOP

Read this before using the Yetter product.

-MACHINE OPERATION

IMPORTANT: failure to properly set the planter frame height and

levelness can result in less than successful operation of the planter

and the Yetter product and may result in damaged equipment. All

operators should read and thoroughly understand the instructions

given prior to using the Yetter product.

NOTE: DO NOT use this product if the planter is not adjusted properly!

Leveling the planter:

With the planter lowered to proper operating height (Usually 20”-22”).

Read the planter operator’s manual for recommended setting. Check to

be sure the toolbar and row unit parallel arms are level fore and aft. Re-

check when the planter is in the field and has been fully loaded with seed,

fertilizer, granular chemicals, etc. Also, a field check with a bubble level on

the frame should be made of the hitch height to ensure level operation front

to back.

It is important for the planter to operate level laterally. Tire pressure must be

maintained at pressures specified by the manufacturer.

Field and actual planting conditions change and will dictate planter frame

heights. You must ensure that the row unit parallel arms are approximately

parallel with the ground.

IMPORTANT: For proper operation of the planter attachments and row

units, it is imperative that the planter toolbars and row unit parallel arms be

level side-to-side and front-to-rear. The toolbar frame should operate at a

20”-22” height from the planting surface. Check the manufacturer’s

operator’s manual for instructions on how to adjust the frame height and

levelness.

PLANTER ADJUSTMENT

OPERATION

Be sure planter frame is LEVEL and at the height stated in the planter operation manual.

The Residue Manager is designed to work in heavy residue situations especially where

minimum soil movement is required. Depending on conditions and objectives, the 2967 Residue

Manager can be set shallow with the teeth only engaged in the residue so as to clear heavy

residue with minimal soil disturbance. Residue Managers are not recommended when surface

application pre-plant herbicide is used prior to planting.

ROW CLEANER DO’S AND DON’TS

1. DO NOT move soil, Residue Managers are designed to move crop residue only.

2. DO NOT operate planter at slow speeds, ground speed affects how aggressive the spoke

wheels are; operate at sufficient speed to maintain good residue flow.

3. DO NOT expect 100% of crop residue to be cleared, it is not necessary and would necessitate

engaging the soil. The width of path cleared depends on ground conditions, depth setting

and ground speed.

4. DO expect to see wheels occasionally quit turning, indicates ideal (shallow) setting which is

not moving dirt.

5. DO expect the potential to bend or break teeth on wheels in excessively rocky conditions.

6. DO adjust planter frame height 20”-22” and level drawbar correctly. Very important to ensure

planter unit will follow ground contours properly.

7. DO adjust planter row unit down pressure kit correctly to prevent excessive depth.

8. DO expect finely tilled/soft soils to require adjustment due to lack of resistance, the wheel

must turn to move residue.

9. DO expect more adjustments to be required in finely tilled or soft soils. In these conditions,

the planter may lose flotation requiring adjustment of the residue manager to shallower

positions.

INSTALLATION INSTRUCTIONS

STEP 1. Choose the mounting hole in which to attach the R.M. wheels. Attach the R.M.

wheels/hub/shield assemblies to the stem adjustment bracket using 5/8” lock washers

and hex nuts. Adjust the bearing shield to top dead center, rotate slightly forward.

Torque to 150 ft./lbs.

INSTALLATION INSTRUCTIONS

STEP 2A. Attach the screw adjust residue manager assembly to the planter row unit

using 2) ½” x 3-1/2” hex bolts and ½” lock nuts.

2967-053

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Yetter

Yetter

Yetter CAB CONTROL STRIP FRESHENER 2984-050A Manual de usuario

Yetter

Yetter 2966-020A Manual de usuario

Yetter

Yetter 2968-050 Manual de usuario

Yetter

Yetter NARROW ROW Manual de usuario

Yetter

Yetter 5000-025A Manual de usuario

Yetter

Yetter 2967-081 Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter TITAN Series Manual de usuario

Yetter

Yetter TITAN 2967-008A Manual de usuario

Yetter

Yetter 6000-002 Manual de usuario

Yetter

Yetter 2565-980 Manual de usuario

Yetter

Yetter 5000-080 Manual de usuario

Yetter

Yetter 5000-025C Manual de usuario

Yetter

Yetter Systems One Seed Jet II Manual de usuario

Yetter

Yetter 5000-022C Manual de usuario

Yetter

Yetter 2967-180B Manual de usuario

Yetter

Yetter 6010 Planter Unit Manual de usuario

Yetter

Yetter V.T.A. 2982-001 Manual de usuario

Yetter

Yetter 5000-022B Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter TITAN 2960-021A Manual de usuario

Yetter

Yetter 5000-023A Manual de usuario

Yetter

Yetter 25 AVENGER COULTER Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario