Yetter MAVERICK HR PLUS 2984 Series Manual de programación

2984 Series MAVERICK



HR PLUS

OPERATOR & PARTS MANUAL

2565-762_REV_L • 12/2018

YETTER MANUFACTURING CO.

FOUNDED 1930

COLCHESTER, IL 62326-0358

TOLL FREE: 800/447-5777

309/776-3222 (FAX)

WEBSITE: WWW.YETTERCO.COM

E-MAIL: INFO@YETTERCO.COM

TABLE OF CONTENTS

FOREWORD…………………………………………………………3

WARRANTY………………………………………………………….3

SAFETY………………………………………………………………4

BOLT TORQUE……………………………………………………..5

ASSEMBLY INSTRUCTIONS………………………………….6-17

OPERATION……………………………………………………18-22

MAINTENANCE………………………………………………..23-30

PARTS IDENTIFICATION…………………………………….31-56

TROUBLESHOOTING………………………………………...58-59

FOREWORD

You’ve just joined an exclusive but rapidly

growing club.

For our part, we want to welcome you to the

group and thank you for buying a Yetter product.

We hope your new Yetter products will help you

achieve both goals-increase your productivity and

increase your efficiency so that you may generate

more profit.

This operator’s manual has been designed into

four major sections: Foreword, Safety

Precautions, Installation Instructions, and Parts

Breakdown.

This SAFETY ALERT SYMBOL indicates

important safety messages in the manual.

When you see this symbol, be alert to the

possibility of PERSONAL INJURY and carefully

read the message that follows.

The word NOTE is used to convey information

that is out of context with the manual text. It

contains special information such as

specifications, techniques and reference

information of a supplementary nature.

The word IMPORTANT is used in the text when

immediate damage will occur to the machine due

to improper technique or operation. Important will

apply to the same information as specified by

note only of an immediate and urgent nature.

It is the responsibility of the user to read the

operator’s manual and comply with the safe and

correct operating procedure and to lubricate and

maintain the product according to the

maintenance schedule in the operator’s manual.

The user is responsible for inspecting his

machine and for having parts repaired or

replaced when continued use of the product

would cause damage or excessive wear to the

other parts.

It is the user’s responsibility to deliver his

machine to the Yetter dealer who sold him the

product for service or replacement of defective

parts, which are covered by the warranty policy.

If you are unable to understand or follow the

instructions provided in this publication, consult

your local Yetter dealer or contact:

YETTER MANUFACTURING CO.

309/776-4111

800/447-5777

309/776-3222 (FAX)

Website: www.yetterco.com

Email: inf[email protected]om

WARRANTY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This

warranty being expressly limited to replacement at the factory of such parts or products as shall appear to

be defective after inspection. This warranty does not obligate the Company to bear cost of labor in

replacement of parts. It is the policy of the Company to make improvements without incurring obligations to

add them to any unit already sold. No warranty is made or authorized to be made, other than herein set

forth. This warranty is in effect for one year after purchase.

Dealer ___________________________________________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damages to

equipment on which mounted.

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe

practices.

WARNING: Denotes a specific potential hazard

DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study

these precautions carefully and insist that they be followed by those working with you and for you.

Finally, remember this: an accident is usually caused by someone’s carelessness, neglect or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always

lower or block the implement before performing service.

If machine must be serviced in the raised position, jack or block it up to prevent it from accidentally falling

and injuring someone.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough

to cause tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment

to do the same.

Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in

an emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices.

Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

BOLT TORQUE

Note: Right hand and left hand designations are based on sitting in the tractor and facing forward.

READ THESE INSTRUCTIONS FIRST:

1. Improperly tightened bolts will result in damage, breakage, expense, and down time.

2. Always replace bolts with the specified grade and type.

3. Torque properly before first use of the machine and every 2-4 hours of use until you are sure bolts

are staying tight.

4. The chart below is a guide for proper torque. Use it unless a specified torque is called out

elsewhere in the manual.

5. Torque is the force you apply to the wrench handle or the cheater bar, times the length of the

handle or bar.

6. Use a torque wrench whenever possible.

The following table shows torque in ft. lbs.

Lubricate all bearings and moving parts as assembled and make certain that they work freely.

WARNING:

Never work around the toolbar / implement while in a raised position

without using safety lockups.

CAUTION:

The MAVERICK OPENER™and its attachments are very heavy. Extra

attention to lifting techniques while handling and or maneuvering the opener during

assembly. Failure to do so may lead to personal injury.

ASSEMBLY INSTRUCTIONS

2984 MAVERICK OPENER

™

STEP 1. Mark the location of the center of each row on the toolbar. Then measure from row 4” and place a

mark on the rear side of toolbar. This mark will give a reference point to where the edge of the clamp

bracket (3000-409) should be located so that the fertilizer knife will be centered directly on the row.

STEP 2. Centering on each row, attach the (3000-149) parallel arm assembly to the toolbar with the

appropriate ¾” u-bolts, lock washers and hex nuts. Torque the u-bolts to 200 ft. lbs. Recheck the torque

after 10 hours of use.

ASSEMBLY INSTRUCTIONS

STEP 3. Attach the fertilizer knife to the 2984 knife mount using 2) ½” x 2” GRADE. 8 bolts and lock nuts.

(Rock Trip model use 3) ½” x 2” GRADE 8)

STEP 4. Tighten all bolts to recommended torques from the table of this manual, unless the torque is

otherwise specified.

Note: Do not over tighten the spindle bolt and castle nut. Torque the spindle bolt to 13-15 ft. lbs. or until

the hub/blade assembly has a slight drag when turned by hand. Tighten the nut one slot position on the

castle nut to line up the cotter pin hole. Secure the nut with the 1/8” x 1” cotter pin provided.

Recheck the torque on these bolts after 10 hours of operation and then every 50 hours after that. Do a

routine inspection of the opener at this time for best performance and less down time.

ASSEMBLY INSTRUCTIONS

2984-028-ST - RESIDUE MANAGER

2984-029-ND - RESIDUE MANAGER

STEP 1. Install the wheel stem assembly

Initial Adjustment for the residue manager needs to be set at soil surface. For example: fertilizer is to be

placed 6” deep, the residue manager should be adjusted 6” above the tip of the knife.

Field adjustment: In field adjustments to the residue manager will need to be done for best performance of

residue manager. As conditions change, soil types, tilth, moisture, amount of residue, type of residue, the

residue manager’s depth adjustment may also need to change.

ASSEMBLY INSTRUCTIONS

2984-030-N – NOTCHED DISC SEALER KIT

2984-030-S – SMOOTH DISC SEALER KIT

STEP 1.

ASSEMBLY INSTRUCTIONS

2984-030-N – NOTCHED DISC SEALER KIT

2984-030-S – SMOOTH DISC SEALER KIT

STEP 2:

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Yetter

Yetter

Yetter 8500 SERIES Manual de usuario

Yetter

Yetter 2967-002B Manual de usuario

Yetter

Yetter SCREW ADJUST Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter 500 Series Manual de usuario

Yetter

Yetter TITAN Series Manual de usuario

Yetter

Yetter 5000-025B Manual de usuario

Yetter

Yetter 5000-023C Manual de usuario

Yetter

Yetter V.T.A. 2982-001 Manual de usuario

Yetter

Yetter TITAN Series Manual de usuario

Yetter

Yetter 5000-080 Manual de usuario

Yetter

Yetter 5000-022 Lexion C512-30/Capello Manual de usuario

Yetter

Yetter NARROW ROW Manual de usuario

Yetter

Yetter 2968-020B Manual de usuario

Yetter

Yetter 2967-115A Manual de usuario

Yetter

Yetter 2999 Manual de instrucciones

Yetter

Yetter 2966-020A Manual de usuario

Yetter

Yetter 2967-035A Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter 5000-022C Manual de usuario

Yetter

Yetter TITAN Series Manual de usuario

Yetter

Yetter TITAN 2960-021A Manual de usuario

Yetter

Yetter Furrow Max 6200-070 Manual de usuario

Yetter

Yetter Systems One Seed Jet II Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario