Yeastar Technology UF51 5G CPE Manual de usuario

5G CPE

UF51

Installation Guide

Safety Precautions

Yeastar will not shoulder responsibility for any loss or damage resulting from not following the

instructions of this operating guide.

The device must not be modified in any way.

Do not place the device close to objects with naked flames.

Do not place the device where the temperature is below/above the operating range.

Do not power on the device or connect it to other electrical device when installing.

Check lightning and water protection when used outdoors.

Do not connect or power the equipment using cables that have been damaged.

Related Documents

This Installation Guide only explains the installation of Yeastar UF51 5G CPE. For more functionality and

advanced settings, please refer to the relevant documents as below.

Document

Description

UF51 Datasheet

Datasheet for UF51 5G CPE.

UF51 Administrator Guide

IT administrators can refer to the guide for instruction on how to log in

the web GUI, and how to configure all the settings.

The related documents are available on Yeastar website: https://www.yeastar.com

Declaration of Conformity

UF51 is in conformity with the essential requirements and other relevant provisions of the CE, FCC, and

RoHS.

For assistance, please contact

Yeastar technical support:

Email: support@yeastar.com

Tel: 86-592-5085280

Fax: 86-592-5023065

Revision History

Date

Doc Version

Description

July 28, 2021

V1.0

Initial version

Contents

Packing List........................................................................................................................................................4

Overview..................................................................................................................................................... 5

Dimensions (mm)......................................................................................................................................5

Serial & IO & Power Pinouts.....................................................................................................................6

LED Indicators............................................................................................................................................6

Reset Button...............................................................................................................................................7

Power Supply..................................................................................................................................................... 8

Hardware Installation....................................................................................................................................... 9

SIM Card Installation................................................................................................................................ 9

Waterproof Cover & Ethernet Cable Installation...................................................................................9

Device Installation...................................................................................................................................10

Desktop............................................................................................................................................ 10

Wall Mounting..................................................................................................................................10

Pole Mounting................................................................................................................................. 11

Login the Web GUI.......................................................................................................................................... 13

Wireless Access......................................................................................................................................13

Wired Access...........................................................................................................................................13

Packing List

Before you begin to install the UF51 5G CPE, please check the package contents to verify that you have

received the items below.

4 × Rubber Feet

1 × 8-Pin Pluggable

Terminal Block

1 × Bottom Cover

with Cable Gland

1 × Waterproof

Rubber Ring

Wall Mounting Kits

2 × Hose Clamps

1 × Warranty Card

1 × Quick Start Guide

If any of the above items is missing or damaged, please contact your sales representative.

1 × UF51 Device

1 × PoE Injector

1 × Mounting Bracket

1 × Ethernet Cable

Hardware Introduction

Overview

Dimensions (mm)

1LED Indicator Area

STATUS: Power & System Indicator

5G: Cellular Indicator

2Waterproof Connector

3SIM Slot

4Reset Button

5Vent Plug

6LAN2 Port

7Bracket Mounting Screws

8Serial & IO & Power Interface

9LAN1/WAN Port (PoE PD)

Serial & IO & Power Pinouts

LED Indicators

LED

Indication

Status

Description

STATUS

Power &

System

Status

Off

The power is switched off

Orange

Static: The system is startup

Green

Static: The system is running properly

Red

Static: The system goes wrong

Cellular

Status

Off

SIM card is registering or fails to register

(or there are no SIM cards inserted)

Green

Blinking slowly: SIM card has been registered and

is ready for dial-up

Blinking rapidly: SIM card has been registered and

is dialing up now

Static: SIM card has been registered and dialed up

to 5G network

Orange

Static: SIM card has been registered and dialed up

to 4G network

Ethernet

Port

Link Indicator

(Orange)

Off

Disconnected or connect failure

Connected

Blinking

Transmitting data

Rate Indicator

(Green)

Off

100 Mbps mode

1000 Mbps mode

RS232

/RS485

Power

Description

---

Digital Input

GND

---

Ground

---

(-)

Negative

---

(+)

Positive

(9-48V)

---

COM

---

Common

Ground

---

OUT

---

Digital Output

RXD/B

---

RS232-RXD

RS485-B

TXD/A

---

RS232-TXD

RS485-A

Reset Button

Function

Description

STATUS & 5G LED

Action

Reset

Static

Press and hold the reset button for more than 5 seconds.

Static →Blinking

Release the button and wait.

Off →Static Green

The device resets to factory default.

Power Supply

UF51 can be powered by 802.3af standard PoE or 9-48VDC. Both power supplies can’t be used at the

same time.

PoE Supply: Follow the below picture to provide power supply via PoE injector. Besides, UF51 can also

be powered by PoE switch.

DC Supply: Connect the DC power cable to terminal block, then connect the terminal block to DC

interface to power the device.

Hardware Installation

SIM Card Installation

Insert the SIM card into the device according to the direction icon on the device. If you need to take out

the SIM card, press into the SIM card and it will pop out automatically.

Waterproof Cover & Ethernet Cable Installation

If you need to use UF51 outdoors, the waterproof cover and cable gland should be installed under the

bottom of the device.

A. Install the rubber ring into the bottom of the device. Note that the round part needs to face the gap of

bottom when installing, otherwise it may cause waterlogged.

B. Connect a round Ethernet cable to LAN1/WAN port, then pass the Ethernet cable through all parts of

the cable gland and the bottom cover.

C. Fix the bottom cover to the bottom of the device with 4 screws.Note that the arrow behind the cover

needs to face the bracket mounting screws.

Note: Bottom cover can be fixed with the device via the wiring behind the cover.

Device Installation

UF51 supports multiple installation methods like desktop, wall mounting, pole mounting, etc. Before you

start, make sure that your SIM card has been inserted and all cables have been installed.

Note: Do not connect device to power supply or other devices when installing.

Desktop

When using indoors, pile 4 rubber feet into the gaps at the bottom of the device. The rough surface of

rubber feet should face desktop.

Wall Mounting

Preparation: mounting bracket(with 2 screws), wall plugs, wall mounting screws and other required

tools.

A. Align the mounting bracket horizontally to the desired position on the wall, use a marker pen to mark

four mounting holes on the wall, and then remove the mounting bracket from the wall.

Tabla de contenidos

Otros manuales de Cambiar de Yeastar Technology

Yeastar Technology

Yeastar Technology NeoGate TE100 Manual de servicio

Yeastar Technology

Yeastar Technology MyPBX Manual de usuario

Yeastar Technology

Yeastar Technology MyPBX Standard V6 Manual de servicio

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario