YASKAWA Motoman DX200 Manual de usuario

MANUAL No.

HW1483763

DX200 OPTIONS

INSTRUCTIONS

SUPPLEMENT FOR FPD HANDLING USE

Upon receipt of the product and prior to initial operation, read these

instructions thoroughly, and retain for future reference.

MOTOMAN INSTRUCTIONS

MOTOMAN- INSTRUCTIONS

DX200 INSTRUCTIONS

DX200 OPERATOR’S MANUAL (for each purpose)

DX200 MAINTENANCE MANUAL

The DX200 Operator’s manual above corresponds to specific usage. Be sure

to use the appropriate manual.

Part Number: 174117-1CD

Revision: 0

1 of 23

HW1483763

ii HW1483763

operation of Motoman robots, related equipment and software This manual is copyrighted property of

Yaskawa and may not be sold or redistributed in any way. You are welcome to copy this document to

your computer or mobile device for easy access but you may not copy the PDF files to another website,

blog, cloud storage site or any other means of storing or distributing online content.

Printed in the United States of America

First Printing, 2016

Yaskawa America, Inc.

Motoman Robotics Division

100 Automation Way

Miamisburg, OH 45342

Phone: 937-847-6200

www.motoman.com

2 of 23

HW1483763

iii HW1483763

MANDATORY

• This manual explains the controller of the DX200. Read this manual carefully and be

sure to understand its contents before handling the DX200.

General items related to safety are listed in the Chapter 1: Safety of the DX200

instructions. To ensure correct and safe operation, carefully read the DX200

instructions before reading this manual.

CAUTION

• Some drawings in this manual are shown with the protective covers or shields

removed for clarity. Be sure all covers and shields are replaced before operating

this product.

• The drawings and photos in this manual are representative examples and

differences may exist between them and the delivered product.

• YASKAWA may modify this model without notice when necessary due to product

improvements, modifications, or changes in specifications. If such modification is

made, the manual number will also be revised.

• If your copy of a manual is damaged or lost, contact a YASKAWA representative to

order a new copy. The representatives are listed on the back cover. Be sure to tell

the representative the manual number listed on the front cover.

• YASKAWA is not responsible for incidents arising from unauthorized modification

of its products. Unauthorized modification voids your product’s warranty.

3 of 23

HW1483763

iv HW1483763

We suggest that you obtain and review a copy of the ANSI/RIA National Safety Standard for Industrial

Robots and Robot Systems (ANSI/RIA R15.06-2012). You can obtain this document from the Robotic

Industries Association (RIA) at the following address:

Robotic Industries Association

900 Victors Way

P.O. Box 3724

Ann Arbor, Michigan 48106

TEL: (734) 994-6088

FAX: (734) 994-3338

www.roboticsonline.com

Ultimately, well-trained personnel are the best safeguard against accidents and damage that can result

from improper operation of the equipment. The customer is responsible for providing adequately

trained personnel to operate, program, and maintain the equipment. NEVER ALLOW UNTRAINED

PERSONNEL TO OPERATE, PROGRAM, OR REPAIR THE EQUIPMENT!

We recommend approved Yaskawa training courses for all personnel involved with the operation,

programming, or repair of the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

4 of 23

HW1483763

vHW1483763

Notes for Safe Operation

Read this manual carefully before installation, operation, maintenance, or inspection of the DX200. In

this manual, the Notes for Safe Operation are classified as “DANGER”, “WARNING”, “CAUTION”,

“MANDATORY”, or “PROHIBITED”

DANGER

Indicates an imminent hazardous situation which, if not

avoided, could result in death or serious injury to

personnel.

WARNING

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury to

personnel.

CAUTION

Indicates a potentially hazardous situation which, if not

avoided, could result in minor or moderate injury to

personnel and damage to equipment. It may also be

used to alert against unsafe practices.

MANDATORY Always be sure to follow explicitly the items listed under

this heading.

PROHIBITED Must never be performed.

Even items described as “CAUTION” may result in a serious accident in some situations.

At any rate, be sure to follow these important items

To ensure safe and efficient operation at all times, be sure to follow all

instructions, even if not designated as “DANGER”, “WARNING” and “CAUTION”.

5 of 23

HW1483763

vi HW1483763

WARNING

• Before operating the manipulator, check that servo power is turned OFF pressing the

emergency stop buttons on the front door of the DX200 and the programming pendant.

When the servo power is turned OFF, the SERVO ON LED on the programming pendant is

turned OFF.

Injury or damage to machinery may result if the emergency stop circuit cannot stop the

manipulator during an emergency. The manipulator should not be used if the emergency stop

buttons do not function.

Fig.: Emergency Stop Button

• Once the emergency stop button is released, clear the cell of all items which could interfere

with the operation of the manipulator.

Then turn the servo power ON.

Injury may result from unintentional or unexpected manipulator motion.

Fig.: Release of Emergency Stop Button

• Observe the following precautions when performing teaching operations within the P-point

maximum envelope of the manipulator:

- Be sure to use a lockout device for safeguarding when going inside. Also, display a sign

that an operation is being performed inside the safeguarding and make sure no one closes

the safeguarding.

- View the manipulator from the front whenever possible.

- Always follow the predetermined operating procedure.

- Keep in mind the emergency response measures against the manipulator’s unexpected

motion toward you.

- Ensure that you have a safe place to retreat in case of emergency.

Improper or unintended manipulator operation may result in injury.

• Confirm that no person is present in the P-point maximum envelope of the manipulator and

that you are in a safe location before:

- Turning ON the power for the DX200.

- Moving the manipulator with the programming pendant.

- Running the system in the check mode.

- Performing automatic operations.

Injury may result if anyone enters the P-point maximum envelope of the manipulator during

operation. Always press an emergency stop button immediately if there is a problem.

The emergency stop buttons are located on the right of front door of the DX200 and the

programming pendant.

6 of 23

HW1483763

vii HW1483763

CAUTION

• Perform the following inspection procedures prior to conducting manipulator teaching. If

problems are found, repair them immediately,

and be sure that all other necessary processing has been performed.

– Check for problems in manipulator movement.

– Check for damage to insulation and sheathing of external wires.

• Always return the programming pendant to the hook on the cabinet of the DX200 after use.

The programming pendant can be damaged if it is left in the manipulator's work area, on the

floor, or near fixtures.

• Read and understand the Explanation of Warning Labels in the DX200 Instructions before

operating the manipulator:

Definitions of Terms Used Often in This Manual

The MOTOMAN is the YASKAWA industrial robot product.

The MOTOMAN usually consists of the manipulator, the controller, the programming pendant, and

supply cables.

In this manual, the equipment is designated as follows

Equipment Manual Designation

DX200 controller DX200

DX200 programming pendant Programming pendant

Cable between the manipulator and the

controller

Manipulator cable

Registered Trademark

In this manual, names of companies, corporations, or products are trademarks, registered

trademarks, or brand names for each company or corporation. The indications of (R) and TM

are omitted.

7 of 23

HW1483763

viii HW1483763

Customer Support Information

If you need assistance with any aspect of your system, please contact Motoman Customer Support at

the following 24-hour telephone number:

(937)847-3200

For routine technical inquiries, you can also contact Motoman Customer Support at the following

e-mail address:

[email protected]

When using e-mail to contact Motoman Customer Support, please provide a detailed description of

your issue, along with complete contact information. Please allow approximately 24 to 36 hours for a

response to your inquiry.

Please use e-mail for routine inquiries only. If you have an urgent or emergency need for service,

replacement parts, or information, you must contact Motoman Customer Support at the telephone

number shown above.

Please have the following information ready before you call:

• System DX200

• Primary Application FPD Handling

• Controller DX200

• Software Version Access this information on the

Programming Pendant’s LCD

display screen by selecting {MAIN

MENU} - {SYSTEM INFO} -

{VERSION}

• Robot Serial Number Located on the robot data plate

• Robot Sales Order Number Located on the DX200 controller

data plate

8 of 23

HW1483763

Table of Contents

ix HW1483763

Table of Contents

1 Introduction ................................................................................................................................... 1-1

2 Power Capacity............................................................................................................................. 2-1

3 Basic Specifications ...................................................................................................................... 3-1

3.1 Standard module ........................................................................................................................ 3-1

4 Controller Type List....................................................................................................................... 4-1

5 Dimension Diagram and Internal Arrangement Diagram.............................................................. 5-1

6 The List of the Equipment Configuration ...................................................................................... 6-1

7 Recommended Spare Parts List................................................................................................... 7-1

9 of 23

HW1483763

Introduction

1-1 HW1483763

1 Introduction

This manual is a supplementary instruction manual for the DX200.

The described contents are as follows;

i ) Power Capacity

ii ) Basic Specifications

iii ) Controller Type List

iv ) Dimension Diagram and Internal Arrangement Diagram

v) The List of the Equipment Configuration

vi ) Recommended Spare Parts List

For contents that are not described in this manual, refer to the “DX200 INSTRUCTIONS”, “DX200

MAINTENANCE MANUAL”, and all other related documents.

Before using this product, read this manual and all other documents carefully to

ensure knowledge about the product and safety, including all the cautions.

10 of 23

Otros manuales para Motoman DX200

Tabla de contenidos

Otros manuales de Controladores de YASKAWA

YASKAWA

YASKAWA motoman NX100 Manual de usuario

YASKAWA

YASKAWA Z1000 CIMR-ZU*A Series Guía de solución de problemas

YASKAWA

YASKAWA CIMR-VU series Manual de usuario

YASKAWA

YASKAWA PROFINET V1000 Manual de usuario

YASKAWA

YASKAWA PS-V10S Manual de usuario

YASKAWA

YASKAWA SI-EP3 Manual de usuario

YASKAWA

YASKAWA PROFINET V1000 Manual de usuario

YASKAWA

YASKAWA VS-626MT Series Manual de usuario

YASKAWA

YASKAWA Z1000 CIMR-ZU*A Series Manual de usuario

YASKAWA

YASKAWA V1000 Series Manual de instalación y operación

YASKAWA

YASKAWA YRC1000micro Manual de usuario

YASKAWA

YASKAWA pg-b3 Manual de usuario

YASKAWA

YASKAWA MP2300S Manual de usuario

YASKAWA

YASKAWA motoman NX100 Manual de usuario

YASKAWA

YASKAWA PROFINET 1000 Series Manual de usuario

YASKAWA

YASKAWA PROFIBUS-DP SI-P3 Manual de usuario

YASKAWA

YASKAWA JOHB-GA50 Manual de usuario

YASKAWA

YASKAWA YRC1000 Manual de usuario

YASKAWA

YASKAWA G7 Series Manual de usuario

YASKAWA

YASKAWA SI-EP3 Manual de usuario

YASKAWA

YASKAWA YRC1000micro Manual de usuario

YASKAWA

YASKAWA L1000A Series Manual de usuario

YASKAWA

YASKAWA Motoman DX200 Manual de usuario

YASKAWA

YASKAWA PROFINET V1000 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario