Yale YSGA02-W Manual de usuario
Mini Wireless Alarm Kit
YSGA02-W
Part of ASSA ABLOY
12
34
123
Instruction Manual
DE: Bedienungsanleitung
FR: Manuel d'instructions
ES: Manual de instrucciones
IT: Manuale di istruzioni
Battery Installation
1
To insert batteries, open the battery cover.
The unit will beep once to indicate
that the product can now be operated.
Insert 2 x AAA batteries into the battery
compartment. [Please ensure correct polarity.]
LED
PIR Motion Sensor
Screw Fixing
Learn Button
Battery Cover
Battery Compartment
Siren
Keypad
Please note: when
the LED lights remain
‘on’, this indicates the
battery charge is low
and will require
exchanging.
12
34
For the door contact - please remove battery
insulation tab before first use. The device will
beep and can now be used normally.
123
123
Contact Sensor & Magnet
The door contact can be fitted
horizontally or vertically.
TIP:
Siren
1, 2, 3 buttons
Main alarm
Door contact
LED
“Learn” button
CR2 Battery
Setting the 3 Digit PIN code
Change alarm 3 digit pin code
To change the Alarm PIN code, please
enter the default PIN upon initial use:
‘1,2,3’ and then press the 4 key to
acknowledge.
12
34
‘Press 1,2,
3 and 4’.
Save personal 3 digit pin code
Enter 1,2,3, then press the 4 key to acknowledge.
PIN code success
If the red light is OFF,
the PIN code was
successfully
changed.
12
34
Set personal 3 digit pin code
You can then proceed with entering
your 3 digit pin code ‘XXX’.
12
34
‘E.g. 134’
‘Press 1,2,
3 and 4’.
‘4,X,X’
❌
✔
PLEASE NOTE: DO NOT USE the
number ‘4’ at the beginning of your
unique PIN code.
PLEASE NOTE: If the unique PIN code is entered incorrectly 5 times, the beep sound will be emitted
every 2 seconds, ten times and the key bindings will be locked for 5 minutes. After this time, you can
unlock the key bindings by remote control or restore to default settings.
PLEASE NOTE: If a delay of more than 5 seconds occurs between any of the below steps,
the unit will return to standby mode.
PIN code
change failure:
If the red light
flashes 3 times, the
PIN change has
failed and the unit
returns to default
PIN code 1,2,3.
❌
2
Factory reset
Open the battery cover.
Press and hold “Learn” button and
do not release, whilst re-installing
the battery.
Take out the battery.
After three beep sounds, the alarm will return
to the default setting and the password will
restore to default ‘1,2,3’.
PLEASE NOTE: Do not release button
whilst re-installing the battery.
Password defaults to ‘1,2,3’.
3
Pair with remote control
Ensure alarm is UNARMED, open the
battery cover.
Press the “Learn” button and the red
light will flash.
Take the remote control and
open the battery cover.
Press the “Learn” button on the
remote control.
The red light will flash, and the remote
control will send the code. At this time,
you will hear the main alarm beep twice,
indicating that the alarm has
successfully learned the remote
control communication code.
PLEASE NOTE: To allow the main alarm to learn the code of another device, release the learn button to exit the
learning mode. The red light will stop flashing denoting that the operation is complete, and the main alarm will
return to standby status. You can now add another device to the system using the relevant steps.
12
34
If the red lights keep flashing, the battery
is lowand requires replacing.
PLEASE NOTE:
Replace batteries
if red light is
flashing.
4
Pairing the main alarm with the Door Contact
To pair the door contact please ensure the
alarm is disarmed and then remove the
cover of the main alarm unit.
With the battery covers removed from the main alarm and the door contact, please press and hold
the learn button on the main alarm unit, whilst pressing the learn button on the door contact.
Remove the front cover of the door contact.
Release the “Learn” button whereby
the red light will turn off indicating
that the operation is complete and
the main alarm will return to
disarmed mode.
Please replace the battery cover
to the main alarm unit and the
door contact units.
123
123
‘RELEASE’
‘HOLD’
‘HOLD’
5
Unlinking a paired device
Open the battery cover. Take out the
battery, press ‘3’ and do not release
whilst installing the battery.
After three beep sounds, the Contact will
return to the default setting and the password
will restore to default ‘1,2,3’.
123123
123
6
Remove the backing tape from the door
magnet.
Use the 3M tape to fix the door contact
onto the door/window frame.
Align directly opposite the main alarm,
not exceeding an 8mm gap when
door/window is closed.
123
123
123
123
Installing the door contact
Operation Settings: Setting the PIN
To change the Door Contact PIN code,
please enter the default PIN, ‘1,2,3’,
upon initial use.
If the red light is OFF, the PIN code was
successfully changed.
Enter the default code a second time and
the red light will flash. You can then proceed
with entering your unique 3 digit PIN code.
To arm your alarm simply press the "3"
button, then to disarm your alarm enter
your unique 3 digit PIN code.
PLEASE NOTE: If the unique code is entered incorrectly five times, the alarm will beep every two
seconds, 10 times and the key bindings will be locked for five minutes.
123
123123
123123
‘Press 1,2,3.’
123PLEASE NOTE:
Don’t use the
number ‘3’ at the
beginning of your
unique PIN code.
❌
Factory Reset
Open the battery cover and take out the
battery, press and hold the learn button
and do not release whilst reinserting the
battery.
After three beep sounds, the Door Contact will
return to the default setting and the password
will restore to default ‘1,2,3’, the alarm will
be put into an unarmed state.
123123
123
‘Enter your
unique
code’
PLEASE NOTE: If the red light flashes
three times, the PIN code change was not
successful.
‘3,X,X’
❌
7
Alarm sound ON and OFF settings: Turn ON the alarm sound
When the alarm is unarmed, enter your
PIN followed by the ‘4’ key.
The red light will flash three times.
Press 4 and then press 21.
Once the main alarm is armed, if it is
triggered it will automatically notify other
paired devices connected to it.
12
34
12
34
‘E.g 1, 2, 3, 4’
12
34
‘4, 21’
12
34
123
8
Alarm sound ON and OFF settings: Turn OFF the alarm sound
When the alarm is unarmed, enter your
PIN followed by the ‘4’ key.
The red light will flash three times.
Press 4 and then press 22.
Once the device is armed, if this is triggered,
the device will automatically notify other
paired devices around and WILL NOT sound
the alarm.
12
34
12
34
‘4, 22’
12
34
9
123
‘E.g 1, 2, 3, 4’
12
34
Tabla de contenidos
Otros manuales de Sistema de seguridad de Yale
Yale
Yale SDA16 Manual de usuario
Yale
Yale HSA6600 Manual de usuario
Yale
Yale Sync IA-310 Manual de usuario
Yale
Yale IA-230 Manual de usuario
Yale
Yale IA-210 Manual de usuario
Yale
Yale SAA8012 Manual de usuario
Yale
Yale Sync Alarm Guía de instalación
Yale
Yale HSA 6300 Manual de usuario
Yale
Yale DAS1100 Manual de usuario
Yale
Yale HSA6092 Manual de usuario
Yale
Yale SR-310 Manual de usuario
Yale
Yale SV-4C-2ABFX-2 Manual de usuario
Yale
Yale HSA3400 Manual de usuario
Yale
Yale HSA 3500 Manual de usuario
Yale
Yale Y402A-HD Manual de usuario
Yale
Yale SAA8011 Manual de usuario
Yale
Yale HSA6200 Manual de usuario
Yale
Yale Y402B-HD Manual de usuario
Yale
Yale SAA8012 Manual de usuario
Yale
Yale AC-WS Manual de usuario
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario