Yakima HoldUp Manual de usuario

1034426J-1/21

HoldUp

SAFETY CLIP (1X)

WRENCH (1X)

REAR WHEEL TRAY

ASSEMBLY (1X)

FRONT WHEEL TRAY

ASSEMBLY (1X)

HITCH BOLT (1X)

1 1/4" BASE (1X)

(1 1/4" HOLDUP ONLY)

2" BASE (1X)

(2" HOLDUP ONLY)

LOCK WASHER (1X)

KEY (2X)

HEX WRENCH (1X)

HITCHLOCK (1X)

For Your

Safety

Warranty

Registration

on-line

YAKIMA.com

 Install This product on 2" OR 1¼" hitch

receivers ONLY.

 Do not use with hitch-extenders or with

1 ¼” hitch adapters.

 Do not install on trailers, campers, or RVs.

 Do not install if spare tire causes

interference with bikes, or folded carrier.

 Not for use on bikes with front fenders.

In addition, some undersized receivers may

not accept this product. If you do not know the

capabilities of your hitch receiver, consult an

automotive professional.

IMPORTANT WARNING

IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER

ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR

TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS

PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU

MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION

OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT

THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.

1034426J-2/21

INSERT BASE INTO

HITCH RECEIVER.

The holes in

the base must

align to the

holes in the

hitch receiver.

FASTEN HITCH BOLT.

 Insert hitch bolt and lock washer, from RIGHT TO LEFT.

 Tighten with wrench.

REMOVE FASTENERS.

The fasteners are installed in the trays

for shipping purposes. Remove them to

prepare for assembly.

SECURE HITCH

BOLT WITH

SAFETY CLIP

AND INSTALL

HITCHLOCK.

ROTATE BASE TO

UP POSITION.

 Squeeze knob to release lock.

 Pull spring pin to release base.

 Lift frame.

 Release spring pin. Pin should

snap into place and lock.

1 1/4" - 75 ft-lbs.

2" - 100 ft-lbs.

1034426J-3/21

ATTACH FIRST TRAY TO BASE.

LOWER TRAY:

IMPORTANT: Wheel strap

is to your right, and pivot

arm is to your left.

wheel strap

pivot arm

ATTACH SECOND TRAY TO BASE.

pivot arm

wheel strap

 Align holes in tray to be centered in slots on base.

 Insert bolt, washer, and lock-washer, in order shown.

 Finger tighten all four bolts.

 Tighten with supplied wrench.

 Align holes in tray to be centered in slots on base.

 Install bolt, lock-washer, and washer, in order shown.

 Finger tighten all four bolts.

 Tighten with supplied wrench.

UPPER TRAY:

IMPORTANT: Wheel

strap is to your left, and

pivot arm is to your right.

17 ft-lbs.

1034426J-4/21

Rotate the pivot arm

up until the hook

rests on the bike tire

1” or less from the

brakes or the fork.

Failure to place wheel

hook in the correct

position can cause

your bicycle to eject,

and cause personal

injury, property

damage, or death.

SWING PIVOT ARM INTO PLACE.

CAUTION: If any part

of your bike comes in

contact with the red

trigger, do not use this

carrier with that bike.

FOLD HOLDUP DOWN.

Be sure pivot

arms are

folded down.







into place.

Note: HoldUp can fold down

past horizontal to aid in

loading your bikes.

LOAD HEAVIEST BIKE FIRST.

PREPARE FOR LOADING.

Do not install if your bike

has a ﬂat tire or has a slow

leak. Lost tire pressure

after install may result in

an insecure load.

Tuck strap into slot at

rear of wheeltray.

Release wheelstrap by pressing the

lever on the buckle.

If a fender prevents proper placement

of the wheel hook, remove the fender

for proper and safe loading.

Be sure to return the HoldUp to the locked

horizontal position after loading.

Do not push

arm beyond

horizontal.

1034426J-5/21

 Alternate bike direction.

 Refer to steps 10 through 14

to load your second bike.

If you have bike to bike

interference when loading

two bikes, adjust trays as

necessary to eliminate

interference between bikes.

 Loosen the 4 tray bolts (do

not remove bolts).

 Slide the tray left or right.

 Retighten the 4 tray bolts.

 Both trays can be adjusted.

If necessary adjust tray position to avoid bike to bike interference.

Feed the strap through

the spokes of wheel.

SECURE REAR

WHEEL STRAP.

TIGHTEN REAR

WHEEL STRAP.

Rotate the wheel

slightly, if necessary.

LOAD SECOND BIKE (IF APPLICABLE).

 Thread strap through

spokes and insert it into

the slot in the wheeltray.

 Pull hard to tighten.

SECURE THE HOOK.

Compress

the hook

against the

wheel by

applying

ﬁrm

pressure.

1034426J-6/21

 Access locking cables at

the end of each pivot arm.

 Wrap locking cable

around bike frame.

 Insert the pin from the

pivot arm into hole at the

end of the locking cable.

Lock with key.



 





CHECK THE

INSTALLATION

BEFORE

DRIVING AWAY.

READ ALL WARNINGS ON NEXT PAGE BEFORE DRIVING AWAY.

ALWAYS USE INTEGRATED LOCKING CABLE WHEN TRANSPORTING BIKES.

Slide the hook

against the rear

wheel cradle.

Fold up HoldUp.

SECURE PIVOT ARMS WHEN NOT IN USE.

WHEN NOT CARRYING BIKES ALWAYS FOLD HOLDUP UP.

Tilt wheeltray

inboard.

Rotate pivot

arm down.

Fold wheeltray

inboard.

 

Ajuste la correa si es necesario.

1034426J-7/21

TECHNICAL ASSISTANCE OR REPLACEMENT PARTS: GO ONLINE: WWW.YAKIMA.COM

Contact your dealer or call: (888) 925-4621 Monday through Friday 7:00 am to 5:00 pm PST

Attachment hardware can loosen over time. Check before each use, and tighten if necessary.

Failure to obey load limits can result in property damage, personal injury, or death.

HITCH LOAD IS LIMITED TO 60 LBS. PER BIKE.

This product is covered by YAKIMA’s

“Love It Till You Leave It” Limited Lifetime Warranty

To obtain a copy of this warranty, go online to www.yakima.com

or email us at [email protected]

or call (888) 925-4621

BOTTLE OPENER

Enjoy a refreshing beverage.

Your HoldUp endcap

doubles as a bottle opener!

IMPORTANT LOAD LIMITS:







hot exhaust.



interference with bikes or folded carrier.

BIKES:



recommended pressure found on the tire.



Do not transport bicycles with attached

baby seats, panniers, wheel covers, full

bike covers or motors.

INSTALL THIS PRODUCT

ON 2" AND 1 1/4" HITCH

RECEIVERS ONLY.

MAINTENANCE: Periodically use non-water

soluble lubricant on moving metal parts. Use

a soft cloth with water and mild detergent to

clean rubber parts.

Do not use with a hitch-extender.

Do not use with a 1-1/4" hitch adapter.

Not for use on bikes with front fenders.

In addition, some undersized receivers

may not accept this product. If you do not

know the capabilities of your hitch receiver,

consult an automotive professional.

KEEP THESE INSTRUCTIONS!

MAINTENANCE

Remove this rack before entering an

automatic car wash, and when not in use.

1034426J-8/21

HoldUp

AVERTISSEMENT IMPORTANT:

IL EST IMPÉRATIF QUE LES PORTE-BAGAGES ET LES ACCESSOIRES YAKIMA SOIENT CORRECTEMENT ET SOLIDEMENT FIXÉS AU

VÉHICULE. UN MONTAGE MAL RÉALISÉ POURRAIT PROVOQUER UN ACCIDENT D’AUTOMOBILE, QUI POURRAIT ENTRAÎNER DES

BLESSURES GRAVES OU MÊME LA MORT, À VOUS OU À D’AUTRES PERSONNES. VOUS ÊTES RESPONSABLE DE L’INSTALLATION

DU PORTE-BAGAGES ET DES ACCESSOIRES SUR VOTRE VÉHICULE, D’EN VÉRIFIER LA SOLIDITÉ AVANT DE PRENDRE LA

ROUTE ET DE LES INSPECTER RÉGULIÈREMENT POUR EN CONTRÔLER L’ÉTAT, L’AJUSTEMENT ET L’USURE. VOUS DEVEZ DONC

LIRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS ET TOUS LES AVERTISSEMENTS ACCOMPAGNANT VOTRE PRODUIT YAKIMA AVANT DE

L’INSTALLER ET DE L’UTILISER. SI VOUS NE COMPRENEZ PAS TOUTES LES INSTRUCTIONS ET TOUS LES AVERTISSEMENTS, OU SI VOUS N’AVEZ

PAS DE COMPÉTENCES EN MÉCANIQUE ET NE COMPRENEZ PAS PARFAITEMENT LA MÉTHODE DE MONTAGE, VOUS DEVRIEZ FAIRE INSTALLER

LE PRODUIT PAR UN PROFESSIONNEL.

BROCHE DE

SÛRETÉ (X 2)

CLÉ (X 1)

SUPPORT

ARRIÈRE (X 1)

SUPPORT

AVANT (X 1)

BOULON

D'ATTELAGE (X 1)

BASE 1 1/4 PO (X 1)



BASE 2 PO (X 1)

(HOLDUP 2 PO SEULEMENT)

RONDELLE DE

SÉCURITÉ (X 1)

CLÉS (X 2)

 

51 mm (2 po) OU de 32 mm (1 ¼ po).

 Ne pas employer avec une rallonge

d'attelage ou un adaptateur pour attelage de

32 mm (1 ¼ po).

 Ne pas poser ce porte-vélo sur une

remorque, une autocaravane ou un véhicule

récréatif.

 Ne pas poser ce porte-vélo si la présence de

la roue de secours gêne le chargement des

vélos ou empêche de relever le porte-vélo.

 Ne pas employer si les vélos ont une aile

avant.

Par ailleurs, il est possible que certains

attelages plus petits n'acceptent pas ce

produit. Si l'on ne connaît pas la solidité du

tube d'attelage du véhicule, consulter un

professionnel de l'automobile.

CLÉ HEXAGONALE(X 1)

SERRURE

D'ATTELAGE (X 1)

1034426J-9/21

ENFILER LA BASE

DANS L'ATTELAGE.

Le trous de la

base doivent

s'aligner avec

les trous de

l'attelage.

METTRE EN PLACE LE

BOULON D'ATTELAGE.

 Enﬁler le boulon muni de sa rondelle DE



 Serrer avec la clé.

BLOQUER LE

BOULON AVEC

LA BROCHE

DE SÛRETÉ

ET POSER LA

SERRURE.

RELEVER LA BASE EN POSITION

VERTICALE.







libérer la base.





en place et se verrouiller.

32mm (1¼po): 75pi/lb

5cm (2po)  : 100pi/lb

ENLEVER LES BOULONS.

Les boulons sont vissés dans les supports

pour le transport. Les enlever avant de

procéder au montage.

1034426J-10/21

FIXER LE PREMIER SUPPORT À LA BASE.

Courroie crantée

Bras pivotant

FIXER LE DEUXIÈME SUPPORT À LA BASE.

Bras pivotant

Courroie crantée

 Centrer les trous du support dans les rainures de la base.

 Enﬁler les boulons, les rondelles de sécurité et les



 Serrer les quatre boulons du bout des doigts.

 Serrer avec la clé fournie.

 Centrer les trous du support dans les rainures de la base.

 Enﬁler les boulons, les rondelles de sécurité et les



 Serrer les quatre boulons du bout des doigts.

 Serrer avec la clé fournie.

17pi/lb

SUPPORT INFÉRIEUR :

IMPORTANT : Placer la courroie

crantée à droite et le bras

pivotant à gauche.

SUPPORT SUPÉRIEUR :

IMPORTANT : Placer la

courroie crantée à gauche

et le bras pivotant à droite.

Otros manuales para HoldUp

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios para automóviles de Yakima

Yakima

Yakima Landing Pad 21 Manual de usuario

Yakima

Yakima K1033 Manual de usuario

Yakima

Yakima LOCKN'LOAD Manual de usuario

Yakima

Yakima K976 Manual de usuario

Yakima

Yakima LANDSHARK Manual de usuario

Yakima

Yakima EXO SnowBank Manual de usuario

Yakima

Yakima 8007078 Manual de usuario

Yakima

Yakima LoadRanger 16s Manual de usuario

Yakima

Yakima Whispbar K621W Manual de usuario

Yakima

Yakima BoatLocker Manual de usuario

Yakima

Yakima FlipSide 4 Manual de usuario

Yakima

Yakima StickUp Manual de usuario

Yakima

Yakima KingPin 4 Manual de usuario

Yakima

Yakima LOCKN'LOAD 8000350 Manual de usuario

Yakima

Yakima GateKeeper Evo Manual de usuario

Yakima

Yakima LANDING PAD 17 Manual de usuario

Yakima

Yakima Raptor Aero Manual de usuario

Yakima

Yakima K999 Manual de usuario

Yakima

Yakima Locking RailRider 2 Manual de usuario

Yakima

Yakima FlipSide 4 Manual de usuario

Yakima

Yakima OverHaul HD Manual de usuario

Yakima

Yakima DoubleDown 2 Manual de usuario

Yakima

Yakima S.U.P. Brah Manual de usuario

Yakima

Yakima K834 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

Prorack

Prorack K1163 Manual de usuario