Xilinx ZCU102 Manual de usuario
Zynq UltraScale+ MPSoC
ZCU102 Evaluation Kit
Quick Start Guide
The ZCU102 Evaluation Kit contains all the hardware, tools, and IP required to evaluate and develop your Zynq®
UltraScale+™ MPSoC design.
This quick start guide provides instructions to set up and configure the board, run the built-in self-test (BIST), install
the Xilinx tools, and redeem the license voucher. The guide also provides a link to additional design resources
including reference design schematics, user guides, and reference designs.
ZCU102 Evaluation Kit
For more information, visit www.xilinx.com/ZCU102.
X-Ref Target - Figure 1-1
USB Cables
Ethernet
Cable
Power Supply
and Power
Cables
USB Hub
ZCU102
Base Board
USB Adapter
2
Built-In Self-Test (BIST) Instructions
ZCU102 Evaluation Kit
STEP 1: Set Configuration Switches
Set mode switch SW6 to QSPI32.
Note: For this DIP switch, in relation to the arrow, moving the switch
toward the label ON is a 0. DIP switch labels 1 through 4 are equivalent to
Mode pins 0 through 3.
STEP 2: Connect Power
Plug the power supply into a power outlet with one of the included power
cords.
Connect the 6-pin power supply plug to J52.
Turn on the board power with the SW1 slide switch.
If the three rows of Power Good LEDs glow green, the power system is good.
If the DONE LED circled here glows green, the Zynq UltraScale+ device has
configured successfully.
STEP 3: Initialize Configuration
The built-in self-test (BIST) starts shortly after power on.
Note: Pressing the POR_B (SW4) switch causes the DONE LED to go out,
the FPGA to configure again, and the BIST to restart.
The PL LEDs flash on and off several times at the start of the BIST.
Boot Mode Mode Pins [0:3]
QSPI32 1234
0100
Power Good and
DONE LEDs
3
Self-Test Assignments for PL LEDs
STEP 4: Run the Built-In Self-Test
The BIST consists of a set of pass/fail tests that run sequentially. As each test passes, its corresponding LED glows
green. If a test fails, its corresponding LED is off. The flashing LEDs are next to SW13. For SW13, up is ON or 1.
Note: To pass the PL DIP test, all the switches in SW13 must be up before any of them are moved down. The
LEDs flash faster after you begin the DIP or pushbutton (PB) test.
• The Clock, BRAM, PL-DDR4, PS-DDR4, Flash, and I2C tests run without user input.
• The DIP switch test (SW13) waits for you to move all the DIP switches toward the label ON, and then back.
• The PB test waits for you to push all the pushbuttons. The N, W, S, and E pushbuttons can be pushed in any
order, but push the center button (SW15) last.
• The LED for the test that is waiting for your input slowly flashes on and off.
MSB→LSB
7 6 5 4 3 2 1 0
Clock BRAM PL-DDR4 PS-DDR4 Flash I2C DIP PB
X-Ref Target - Figure 1-2
SW6
J52 (12V Power)
SW1 (Power-On)
Power Good LEDs
DONE LED
SW4
SW15 (PB Switches)
PL LEDs and PL DIP (SW13)
Photo can vary from product.
4
XTP426 (v1.2) July 31, 2017
Install Xilinx Tools and Redeem the License Voucher
A Vivado® Design Suite: Design Edition voucher code is included with the ZCU102 Evaluation Kit. This Vivado
license is node-locked and device-locked to the XCZU9EG device.
STEP 5: Redeem the Vivado Tools License Voucher
To redeem the voucher code, go to www.xilinx.com/getlicense and enter the voucher code shown below. After it is
redeemed, the licenses appear in your entitlement account, and you can generate a license file, which will be
emailed to you. For additional assistance redeeming your voucher, go to www.xilinx.com/kits/voucher.
Note: This code can only be used once and must be redeemed within one year of purchase.
STEP 6: Install the Vivado Design Suite
a. To install the Vivado Design Suite, go to www.xilinx.com/download. Select and download the latest version
of Vivado tools for your operating system.
b. The Vivado installation flow will open the Vivado License Manager. Under the Get License heading, select
Load License. Click Copy License. In the Select License File dialog, navigate to where you saved the license
file that was emailed to you in Step 5. Select the .lic file. Click Open.
c. If you need assistance, review the Vivado installation guide at www.xilinx.com/kits/vivadoinstall.
Next Steps
Learn More
To learn more, please go to the product page (www.xilinx.com/zcu102) which provides an extensive collection of
resources, including a detailed reference design guide, schematics, a hardware user guide, and other reference
designs to accelerate you through developing your product.
Support
For support options related to this product, see the Xilinx support website at www.xilinx.com/support.
Warranty
For the product warranty, go to www.xilinx.com/kits/warranty.
© Copyright 2016–2017 Xilinx, Inc. Xilinx, the Xilinx logo, Artix, ISE, Kintex, Spartan, Virtex, Vivado, Zynq, and other designated brands
included herein are trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respective
owners.
X-Ref Target - Figure 1-3
,PSRUWDQW
,PSRUWDQW
Otros manuales para ZCU102
5
Tabla de contenidos
Otros manuales de Placa madre de Xilinx
Xilinx
Xilinx ML310 Manual de usuario
Xilinx
Xilinx ZC702 Manual de usuario
Xilinx
Xilinx AMS101 Manual de usuario
Xilinx
Xilinx Zynq-7000 ZC702 Manual de usuario
Xilinx
Xilinx ML631 Manual de usuario
Xilinx
Xilinx FMC XM105 Manual de usuario
Xilinx
Xilinx KC705 Si5324 Manual de usuario
Xilinx
Xilinx Virtex-7 FPGA VC7222 IBERT Manual de usuario
Xilinx
Xilinx Avnet Ultra96-PYNQ Manual de usuario
Xilinx
Xilinx Spartan-3 Manual de usuario
Xilinx
Xilinx Arty A7 Manual de usuario
Xilinx
Xilinx ZC702 Manual de usuario
Xilinx
Xilinx Virtex-7 FPGA VC7222 IBERT Manual de usuario
Xilinx
Xilinx ZCU111 Manual de usuario
Xilinx
Xilinx ZC706 Manual de usuario
Xilinx
Xilinx SP623 Manual de usuario
Xilinx
Xilinx VC709 Manual de usuario
Xilinx
Xilinx KCU105 Manual de usuario
Xilinx
Xilinx ML605 Manual de instalación
Xilinx
Xilinx EK-U1-VCU128-G-J Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
