Workrite Ergonomics FDEX30-48-X Manual de programación

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 7

Parts Included

Assembly & Installation Instructions:

Fundamentals 2-Leg Workcenter FDEX30-48-X / FDLX30-48-X

JPower Supply

Qty: 1

OPower Cable - 3.5 meters

Qty: 1

NLeg Cable - 1 meter

Qty: 1

AMaster Leg

Qty: 1

CShort Bracket

Qty: 4

DLe End Bracket

Qty: 1

ERight End Bracket

Qty: 1

BCompanion Leg

Qty: 1

PFeet

Qty: 2

F4 mm Allen Wrench

Qty: 1

QStandard or

Programmable Switch

Qty: 1

KCable Spool

Qty: 1

M" Cable Loops

Qty: 5

HFoot Glide

Qty: 4

G#M6 × 14 mm Flat Head Cap

Screw

Qty: 20

L#8 × ⅝" Pan Head Screw

Qty: 7

I#12 × ¾" Pan Head Laminate

Top Screw

Qty: 21

Sold Separately:

Worksurface

2 of 7 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

WARNING: Maximum loading of table assembly is 125 lb. (56.7 kg.). Maximum load includes the

weight of the table top itself, any equipment placed upon it, and any equipment suspended or hanging under it. Loading

should be evenly distributed over table surfaces. “Payload Capacity” is the Workrite Ergonomics recommended maximum

loading which includes the Workrite sourced table top.

Fundamentals 2-leg

V = 120VAC, 60Hz / 2.5 A maximum

IMPORTANT SAFETY INSTRUCTIONS:

When using an electrical furnishing, basic precautions should always be followed, including the following:

Read all instructions before using this Fundamentals Workcenter.

DANGER:To reduce the risk of electric shock, always unplug this Fundamentals Workcenter from the

electrical outlet before cleaning.

WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Unplug from outlet before putting on or taking o parts.

2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.

3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended

by the manufacturer.

4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or

damaged, or dropped into water. Return the furnishing to a service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, remove plug from outlet.

9. Each surface intended to support an equipment payload capacity of 125 pounds.

FOR COMMERCIAL USE ONLY

SAVE THESE INSTRUCTIONS

IMPORTANT NOTE!

You must complete initialization (Step 10) at the end of

assembly or your workcenter WILL NOT FUNCTION PROPERLY.

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 7

G#M6 × 14 mm Flat Head

Cap Screw

Attach Short & Medium Brackets

1.1 Attach Short Brackets (C) using Allen Wrench (F) and Flat Cap

Screws (G) to both legs. Do not tighten screws completely.

1.2 Attach Right End Bracket (E) to sides of the right (Master) Leg (A) using Flat Cap Screws (G). Attach Le End

Bracket (D) to sides of the le (Companion) Leg (B) using Allen Wrench (F) and Flat Cap Screws (G) and tighten

securely.

Note: the right leg will be on your le and vice versa when the assembly is seen upside down.

✓ Verify that you have all the tools needed for the assembly

You will need the following tools:

#2 tip Phillips screwdriver or drill/driver

#3 tip Phillips screwdriver or drill/driver

M4 tip bit or 4 mm Allen Wrench (E)

If you do not have a Workrite worksurface, you will also need:

⅛" pilot drill bit

3⁄32" pilot drill bit

Hardware at actual size Le (Companion) legRight (Master) leg

front

To avoid stripping the threads, always

insert and make the first few turns

of the screw BY HAND with an Allen

wrench (F), ensuring it is in straight.

1.1

1.2

1.1

4 of 7 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Needs feet attached

6⅛"

2⅞"

front

Pre-drilled Worksurface

Note: For Workrite Top, position leg

assembly to align mounting holes

in brackets to pre-drilled holes in

worksurface.

For Non-Workrite Top, follow steps

below.

2.1 Position leg assemblies on bottom

side of worksurface 6" from front

of top and 2" from side as shown in

illustrations.

2.2 Mark placement of mounting holes,

then use ⅛" drill bit to drill pilot

holes at marked locations. You may

wish to mark your drill bit so you do

not drill any more than ¾" deep and

damage your worksurface top.

Do not drill all the way through worksurface!

Attach Base to the drilled Worksurface

3.1 Install four (4) #12 × ¾" Pan Head

Laminate Top Screw (I) in corners. Leave

lose for next step.

3.2 Install remaining #12 × ¾" Pan Head

Laminate Top Screw (I) and tighten

securely. If you use electric screwdriver,

be sure it is on the lowest torque setting

to avoid stripping the holes on top.

3.3 Tighten first four (4) screws securely.

Do not drill all the way through

worksurface!

I#12 × ¾" Pan Head

Laminate Top Screw

Hardware at actual size

3 screws per

Short Bracket (C) 4 screws per End

Bracket (D & E)

2.2

2.1

3.2

3.1

3.3

Note: For 2-Leg Equal Corner and 120° Worksurface

Mounting Instructions, go to: www.workriteergo.com/instructions

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 7

L#8 × ⅝" Pan Head

Screw

4 Attach Feet & Install Foot Glides

4.1 Install Feet (P) using #M6×14mm Flat Head Cap Screws (G)

included with this Frame Set.

4.2 Attach Foot Glides (H) to bottom of the Feet supplied in your

Foot Kit.

5 Attach Switch

Install your switch (Q) using two #8 × " Pan Head Screws (L).

Be sure the longer end of the

foot goes towards the front

of the workcenter.

Attach Cable Spools and Cable Loops

6.1 Attach Cable Spool (K) with the #12 × ¾"Pan Head Laminate Top Screw (I) to underside of worksurface.

6.2 Attach Cable Loops (M) to underside of worksurface using the #8 × ⅝” Pan Head Screw (L) making sure to wrap

the Cable Loop around the cable prior to attaching.

G#M6 × 14 mm Flat Head

Cap Screw

Hardware at actual size

Caution!

Only use the #M6 × 14 mm Flat Head

Cap Screw (G) for assembly.

Hardware at actual size

4.1

4.2

6.1

6.2

6 of 7 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Connect Leg Cables to Master leg and Companion Leg

7.1 Connect the Leg Cable (N) to the six position connector labeled “1” on both the Master Leg and the Companion

Leg (B).

7.2 Insert the Power Cable (O) into the two position connector labeled “DC” on the Master Leg.

7.3 Insert the Control Cable into the data connector labeled “A1” on the Master Leg.

Connect Power Cable to the Power Supply and put workcenter upright

8.1 Connect the Power Cable (O) to the Power Supply (J).

8.2 Turn the table over into an upright position.

8.3 Plug the Power Cord into the power outlet.

Never connect or remove leg or

control cables when power is

connected! Doing so will damage

the Master Leg.

Control Cable

Master Leg

Companion Leg

7.1

7.2

7.3

7.2

8.1 8.2

8.3

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 7

#1500442- Rev B

Initialize Legs

Aer all legs and the control are connected, and the power cord has been plugged in, hold the down arrow on

the control until the legs make a short motion down and then back up. This initializes and synchronizes the

table legs.

Adjust Feet Guides

If necessary, adjust leveling guides on table feet to level the worksurface. Unscrew to increase height, screw in to

decrease height.

Set Control Switch Initial Settings (FDLX30-48-X only)

11.1 Press the DOWN button to move table to its lowest position.

11.2 If using a worksurface other than a Workrite top, measure height of table from floor to top of worksurface.

If using a Workrite worksurface, the number to use will be 27.5".

11.3 Press and hold both the UP and DOWN buttons simultaneously. Three dashes will appear. Wait for the numeric

display to return.

11.4 Press the UP button until the display reads 27.5" (for Workrite worksurfaces) or measured height (for others).

11.5 The display will flash when the change has been saved.

Cleaning instructions

To clean the legs, apply cleaner to a so cloth.

Suggested cleaners: Windex or Formula 409.

Do not use solvents and do not saturate or spray cleaners directly to table base.

Hold down the down arrow until table

moves slightly upwards

You must complete

this initialization step

or your table will NOT

function properly.

✓

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mobiliario de interior de Workrite Ergonomics

Workrite Ergonomics

Workrite Ergonomics Sierra HX Manual de usuario

Workrite Ergonomics

Workrite Ergonomics SM-ACR Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra HX Manual de usuario

Workrite Ergonomics

Workrite Ergonomics ST2E-5472-4272EOC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDLX5472-4272EOC Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX5472-4272EOC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDEX30-48-X Manual de programación

Workrite Ergonomics

Workrite Ergonomics ACC-HPED-X Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra HXL Crank Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Advent ADV 6030 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sentinel ST2E-54-72 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sentinel ST2E-30-48 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra Privacy Panel Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX7890-4272OC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX78-90 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Essentia ES2E30-48 Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDEX 60-B02-WP Manual de programación

Workrite Ergonomics

Workrite Ergonomics Rise Quiet RISE-3E-3044-X Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX7890-4272OC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra Series Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Sierra 2-Leg Desk SEHX30-48 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Cascade Counterbalance Workcenters CC S... Manual de usuario

Manuales populares de Mobiliario de interior de otras marcas

Homelegance

Homelegance California 1662PEK-1CK Manual de usuario

Osmond Ergonomics

Osmond Ergonomics FLO Manual de usuario

OVE

OVE ELOISE 42 Manual de usuario

overstock

overstock MF286255 Manual de usuario

Sonoma

Sonoma 160-801 Manual de usuario

BOLERO

BOLERO Wicker Side Chair CF158 Guía de instalación

Coaster

Coaster 4799N Manual de usuario

Stor-It-All

Stor-It-All WS39MP Manual de programación

Lexicon

Lexicon 194840161868 Manual de usuario

Next AMELIA NEW 462947 Manual de usuario

Furinno

Furinno 18089 Manual de usuario

Munchkin

Munchkin Push to Close MK0001 Manual de usuario

impekk

impekk Manual II Manual de usuario

Elements

Elements Ember Nightstand CEB700NSE Manual de usuario

JWA

JWA CARY 68429 Manual de usuario

VIPACK

VIPACK AMORI AMKB9014 Manual de usuario

Anthro

Anthro GT03 Series Manual de usuario

Rowico

Rowico SANNA Manual de usuario