Workrite Ergonomics ACC-HPED-X Manual de programación

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 3

0.4126"

#3 Drive

0.134"3/4"

0.216"

#12 Screw Size

Tools Required:

Required, Sold Separately:

Desk or Table

Included:

⅛" Drill Bit Clamp (2x)4 mm Hex Key #3 Phillips Screwdriver

or Drill/Driver

ID Part Name Qty

AHanging Pedestal 1

B #12 × ¾" Phillips Pan Head Screws 6

Cordless Drill

Assembly & Installation Instructions:

Hanging Pedestal

ACC-HPED-X

WARNING: Installation on table with payload below 200 lb not recommended

Weight capacity of Hanging Pedestal is 30 lb

NOTE: Different worksurface materials may require alternative mounting screws

Completely remove drawer

from main body of pedestal.

Flip the plastic tab on

each side of drawer to

release drawer from

main body (right tab

down, left tab up).

REMOVE DRAWER

Main Body

Mounting Bracket

Plastic Tab

Drawer

2 of 3 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Determine where to install the mounting

bracket on the main body.

When main body is positioned ⅞" from

front edge of worksurface, mounting

bracket should be positioned as far back

as possible under the worksurface.

If necessary, reposition bracket on the

main body by removing the two M6 bolts

with 4 mm hex key and shifting bracket.

Then replace and tighten bolts.

DO NOT DRILL DEEPER THAN

¾" INTO WORKSURFACE

Remove clamps and main body

from worksurface

Pre-drill pilot screw holes (x6) on under-

side of worksurface. If using provided

hardware, use ⅛"drill bit.

Position main body ⅞" offset from the front edge

and clamp it to underside of worksurface

Use pencil to mark holes (x6)

WARNING: 1" space required between

main body and other objects (switch, legs, control boxes)

3.1

3.2

3.3

2.1

2.2

2.3

DETERMINE REAR BRACKET LOCATION

ATTACH MAIN BODY TO WORKSURFACE

Mounting Bracket

Crossbar

Main Body

Clamps

Mounting Bracket

⅞" offset

M6 Bolts

Worksurface Front Edge

Previously Marked

Pilot Screw Holes

3 of 3 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Reclamp main body to underside of worksurface

making sure to line up the holes on the main body

to the pre-drilled holes

Attach main body to worksurface using (x6)

#12 × ¾" Phillips pan head screws (B).

REMOVE CLAMPS AND INSERT DRAWER

1500407 Rev B

4.1

4.2

ATTACH REAR BRACKET AND MAIN BODY TO WORKSURFACE

If the worksurface which the

hanging pedestal is being

mounted to is not flat, spacers

may be required to mount.

#3 Phillips Screwdriver

#12 × ¾" Phillips Pan Head Screw

Drawer

Otros manuales de Mobiliario de interior de Workrite Ergonomics

Workrite Ergonomics

Workrite Ergonomics Essentia ES2E30-48 Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra Series Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX5472-4272EOC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDEX 60-B02-WP Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDEX30-48-X Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDLX5472-4272EOC Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra HX Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Cascade Counterbalance Workcenters CC S... Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Sentinel ST2E-54-72 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics FDEX30-48-X Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX7890-4272OC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra 2-Leg Desk SEHX30-48 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sentinel ST2E-30-48 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX7890-4272OC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Advent ADV 6030 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra HX Manual de usuario

Workrite Ergonomics

Workrite Ergonomics SM-ACR Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics ST2E-5472-4272EOC Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Sierra HXL Crank Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Sierra Privacy Panel Manual de usuario

Workrite Ergonomics

Workrite Ergonomics Sierra SEHX78-90 Series Manual de programación

Workrite Ergonomics

Workrite Ergonomics Rise Quiet RISE-3E-3044-X Manual de programación

Manuales populares de Mobiliario de interior de otras marcas

Homelegance

Homelegance California 1662PEK-1CK Manual de usuario

Osmond Ergonomics

Osmond Ergonomics FLO Manual de usuario

OVE

OVE ELOISE 42 Manual de usuario

overstock

overstock MF286255 Manual de usuario

Sonoma

Sonoma 160-801 Manual de usuario

BOLERO

BOLERO Wicker Side Chair CF158 Guía de instalación

Coaster

Coaster 4799N Manual de usuario

Stor-It-All

Stor-It-All WS39MP Manual de programación

Lexicon

Lexicon 194840161868 Manual de usuario

Next AMELIA NEW 462947 Manual de usuario

Furinno

Furinno 18089 Manual de usuario

Munchkin

Munchkin Push to Close MK0001 Manual de usuario

impekk

impekk Manual II Manual de usuario

Elements

Elements Ember Nightstand CEB700NSE Manual de usuario

JWA

JWA CARY 68429 Manual de usuario

VIPACK

VIPACK AMORI AMKB9014 Manual de usuario

Anthro

Anthro GT03 Series Manual de usuario

Rowico

Rowico SANNA Manual de usuario