Winton TM110 Manual de usuario
WINTON TOPPER MOWER
WTM SERIES
OWNERS MANUAL
PLEASE READ THIS MANUAL BEFORE OPERATING THE MOWER
V2 2Winton WTM
Congratulaons on purchasing your new Winton mower!
Before you get started, we have provided a helpful space to jot down a few important
details about your new Winton machine.
Model Number: WTM
Serial Number:
Date of purchase:
Factory Reference: TM110/TM140/TM160/TM180k
This manual should be considered a permanent part of this machine and should remain with it even if
the machine is subsequently sold.
Winton connually seeks advancements in its product design and quality. Therefore, while this manual
contains the most current product informaon available at the me of prinng, there may be minor
discrepancies between your machine and this manual.
If you have any quesons concerning this manual, please consult your local dealer.
First Published: March 2020
V2 1Winton WTM
General Safety Informaon
Ensure all potenal operators read this manual thoroughly before using the machine.
Safety: Ensure tractor and machine is staonary and keys out of ignion before set-up/maintenance.
Safety: Failure to follow good safety standards could result in severe injury or even death.
Misuse: This machine is designed for use with compact tractors, and should be used only for the
indicated purpose. Winton does not take responsibility if the machine is used for any other
purpose. Children must not operate the machine under any circumstance.
Modicaon: Do not modify equipment in any way. This may impair the operaon and overall
safety of the machine.
Tractor requirements: Use only with compact tractors within power range specied.
Misuse transport: Do not use machinery to transport personnel or livestock.
Condion: For the safety of personnel and opmum performance of the machine, you should
check the condion of the machine and the tractor before starng. Before use check all nuts and
bolts are ght.
Spaal awareness: Always check the operang area is safe before starng machinery.
Operator clothing: The operator should not wear loose clothing while operang machinery.
Safety wear: Always use appropriate ear protecon when running a tractor and machinery.
Ensure you are wearing protecve gloves when servicing and using machinery.
Bystander safety: Ensure bystanders keep away from the machine when it is in use. Do not
touch moving parts when the machine is at work.
Public places: When travelling on the road/public places, always keep the PTO turned o.
Maintenance: Always keep the machine maintained and in a good state. Where necessary,
repair or replace any defecve parts. Do not modify the machine.
Sharp objects: Pay aenon to the sharp/pointed parts while servicing the machine.
Safety guards: All protecve parts should be in good condion before operang machinery.
Safety signs/sckers: Keep all safety signs clean and legible. Replace any which are missing or
illegible. If a component with safety sign(s) is replaced, make sure new safety sign(s) are
aached in the same locaons.
Operang speeds: Machinery and PTO should be operated at the recommended speed at all
mes.
Safety awareness: Good safety requires that you familiarise yourself with various safety signs,
the type of warning and the area, or parcular funcon related to that area.
Alertness: Never consume alcohol or drugs as these can hinder alertness/coordinaon. Consult
your doctor about using this machine while taking prescripon medicaons.
V2 2Winton WTM
General Safety Informaon (Connued)
Machinery Pre-Use Checks
On receipt of your new Winton machine and again within the rst 4 hours of use, or the ‘shake in
period’, we always recommend checking over the machine.
• Check all bolts, nuts and screws are ght on the unit.
• Tighten/check any bolts and nuts securing blades.
• If your machine has belts check the tension and adjust if required.
• Apply grease to grease points if necessary.
• Check gear oil level and top up if needed. Do not overll.
Tractor Pre-Use Checks
Check that the machine is properly aached to the tractor. Ensure that secure pins are used on
the linkage mounng pins.
Be sure to add extra weights to the front of the tractor or add wheel weights if required.
Check that the tractor PTO sha turns freely and that the machines PTO drive sha can extend
easily. Grease the PTO drive sha using the grease points.
The chain on the PTO sha should be checked and in a good condion. The universal joints
installed should be in a good state, with proper protecve parts.
Before installing the PTO sha, the tractor and machine should be stopped and the key removed.
Install and secure all safety guards, doors and covers before starng.
Bystanders should leave the immediate area before connecng the drive to the tractor.
Running/Operang Checks
• Always keep the PTO output from the tractor at 540 RPM when running machinery.
Post-Use Regular Checks
Check blades, belts and wearing parts. Be sure they are not damaged and blades swing freely in
their mount. Repair or replace as required.
Clean machinery and check for/clear any entangled material which may have got stuck around
the rotang parts.
V2 3Winton WTM
Contents
Pg.
General Safety informaon 1-2
1. Dimensions and Specicaons 4
2. Installaon & Set Up 5
3. Cung Height & Skid Adjustment 6
4. Blade Replacement 7
5. Gearbox Maintenance 8
6. Servicing & Maintenance 9
7. WTM 110/140/160 Parts Diagram 10
8. WTM 110/140/160 Parts List 11-12
9. Notes 13
10. WTM 180 Parts Diagram 14
11. WTM 180 Parts List 15-16
12. PTO Sha Resizing 17
13. Winton Product Warranty 18
14. FAQ’s & Troubleshoong 19
V2 4Winton WTM
1. Dimensions & Specicaons
*Please note specicaons are for indicaon and are subject to change without noce.
Model WTM110 WTM140 WTM160 WTM180
Weight 175kg 205kg 220kg 385kg
Working Width 110cm 140cm 160cm 180cm
Blade Type
Number Of Blades 2222
Recommended Tractor HP 16-25 HP 23-40 HP 25-50 HP 30-60 HP
Width 125cm 155cm 175cm 195cm
Depth 135cm 165cm 185cm 205cm
Height 100cm 100cm 100cm 100cm
PTO Sha Size 70-100cm 70-100cm 70-100cm 80-120cm
Cung Height 5-25cm 5-25cm 5-25cm 5-25cm
Linkage Size Category 1 Category 1 Category 1 Category 1
V2 5Winton WTM
2. Installaon & Set Up
Safety: Ensure tractor and machine is staonary and keys out of ignion before set-up/maintenance.
Safety: Before aaching/detaching machinery ensure the hydraulic li system is in a neutral posion.
Safety: Make sure the PTO drive isn’t connected at any point unl instructed to do so.
Aaching The Mower
On a at area of ground lower the three point linkage on your tractor to its lowest posion and aach
the mower to the tractor using the three point linkage pins and linch pins.
With the skids on the mower on the ground, adjust the length of the top link arm so that the skids at
the side of the ail mower are parallel with the ground.
Then check the blade height underneath the machine to give an idea of the cung height. Check
clearance between the boom of the blades and the ground, this should be at least 50mm.
Cut height should be raised for rough/lumpy paddocks or cung long grass. This can be through raising
the hydraulic li arms on the tractor or adjusng the skids on the machine to increase the blade
clearance.
The working speed of the machine should always be at a walking pace (approx. 2 to 5 mph) depending
on the working condions. Overgrown grass and weeds should be cut at a much slower pace for the
best cut and to avoid any damage to the mower.
Check PTO sha’s grease points and apply grease if needed. Then aach the PTO drive sha and
ensure locking pin is secure on both the tractor and mower sides. Aach the chain to a secure point on
the tractor/implement.
Operate the mower the with tractor in low range gear and the PTO delivering 540 RPM.
Pre-Mowing Checklist
Before starng the machine, always check and adjust the following:
Set correct cung height [Secon 3]. Check blades [Secon 4]. Check oil level in the gearbox [Secon
5]. Lubricate all grease points [Secon 6]. Check ghtness of all bolts, nuts and screws. Ensure all
protecve guards are in place.
V2 6Winton WTM
3. Cung Height & Skid Adjustment
Safety: Ensure tractor and machine is staonary and keys out of ignion before set-up/maintenance.
Note: Clearance of blades to the ground should be at least 50mm and higher on un-even ground.
Geng the cung height right is the key to geng the best from your mower. The cut height can be
set by simply adjusng the mower deck height with the skids or raising the mower on the linkage.
Cung height should be adjusted for the land and also the length of grass or density of weeds. The
mower should be raised higher from the ground for long/overgrown grass, weeds or small shrubs.
Skid Adjustment
1. Loosen bolts and nuts (1) on the skids on both sides of the machine.
2. Move the skids up or down lining the bolt holes up at the desired height.
3. Re-ghten bolts and nuts (1).
1
V2 7Winton WTM
4. Blade Replacement
Safety: Ensure tractor and machine is staonary and keys out of ignion before set-up/maintenance.
Safety: Always wear protecve gloves and take care when working with sharp blades.
Always replace worn or blunt blades for opmum cung. Broken or chipped blades should be replaced
immediately to ensure the blades do not become loose and the mower deck is balanced. It is always
best to replace blades in pairs for best results. Ensure all bolts are ghtened before operang.
Ensure moving parts are staonery before starng. To gain access to the blades under the deck the
mower should be lied and supported. Use support stands or blocks to hold the mower in place. Check
stability of the unit when working underneath or leaving the mower at a raised height.
Blade removal
1. Loosen and remove blade bolts and nuts (1).
2. Remove the old blades and replace with new ones.
3. Replace and ghten blade bolts and nuts (1).
1
V2 8Winton WTM
5. Gearbox Maintenance
Safety: Ensure tractor and machine is staonary and keys out of ignion before set-up/maintenance.
Safety: Always follow manufacturers instrucons for oils and lubricants.
Important Informaon
Do not mix old and new oils together or mix dierent types of oil. Always dispose of old oils
safely and in the correct manner. Always make sure the machine is on a at and level surface when
checking oil levels. The machine should be le at a standsll to cool down for at least 10 minutes. En-
sure the machine is stable before carrying out work and will not upturn.
Draining oil: Use an oil pump to remove old oil and any debris when changing oil.
Bolt tension: Always make sure bolts are ghtened correctly. The ller/level plug should be secure but
not over ghtened.
Oil Change/Check Gearbox
1. Remove ller/breather plug (1) on top of the gearbox unit.
2. Remove level plug (2) on the side of the gearbox.
3. Add oil through the ller/breather (1) (if required). The oil should reach/begin to weep from
level plug (2).
4. Replace ller/breather plug (1) and level plug (2).
Gear Oil Grade 80w90 gear oil (grade GL5) for all condions (or equivalent)
Gearbox Oil Level Approx. 0.5 litres to level plug
First Oil Change 50 hours use
Oil Change Frequency 250 hours/yearly (whichever is rst)
Oil Change #1 Oil Change #2 Oil Change #3 Oil Change #4 Oil Change #5 Oil Change #6
/ / / / / / / / / / / /
21
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Accesorios para tractores de Winton
Winton
Winton WRT Series Manual de usuario
Winton
Winton WLR Series Manual de usuario
Winton
Winton WTL Series Manual de usuario
Winton
Winton WRP Series Manual de usuario
Winton
Winton WBS01 Manual de usuario
Winton
Winton WFM Series Manual de usuario
Winton
Winton WCF Series Manual de usuario
Winton
Winton WTM Series Manual de usuario
Winton
Winton WRB Series Manual de usuario
Winton
Winton WSB Series Manual de usuario
