Wilson Electronics 801105 Manual de usuario

Amplifier

Installation

Guide

In-Building

Wireless

Amplier

MODEL# 801105

MODEL# 801106

MODEL# 801306

MODEL# 804005

MODEL# 804006

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1

Antenna Options and Accessories · · · · · · · · · · · · · · · · · 2

Before Getting Started / How It Works · · · · · · · · · · · · · · 3

Quick Start Guide · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4

Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · · 5

Installing a Wilson Inside Antenna · · · · · · · · · · · · · · · · · 6

Installing a Wilson Amplier · · · · · · · · · · · · · · · · · · · · · · 7

Powering Up a Wilson Amplier · · · · · · · · · · · · · · · · · · · 8

Understanding the Amplier Lights · · · · · · · · · · · · · · · · · 9

Troubleshooting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10

Cell Phone Overload Protection · · · · · · · · · · · · · · · · · · 11

Warnings and Recommendations · · · · · · · · · · · · · · · · · 12

Finding Signal Strength and Coverage Distance · · · · · · 12

Amplier Specications · · · · · · · · · · · · · · · · · · Back Cover

Wilson

Electronics, Inc.

Warning: This manual contains

important safety and operating information.

Please read and follow the instructions

in this manual. Failure to do so could be

hazardous and result in damage to your

amplier.

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson’s 30-day money-back

guarantee. If for any reason the performance of any product is not acceptable,

simply return the product directly to the reseller with a dated proof of purchase.

1-Year Warranty

Wilson Electronics ampliers are warranted for one (1) year against defects in

workmanship and / or materials. Warranty cases may be resolved by returning the

product directly to the reseller with a dated proof of purchase.

Ampliers may also be returned directly to the manufacturer at the consumer’s

expense, with a dated proof of purchase and a Returned Material Authorization

(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either

repair or replace the product. Wilson Electronics will pay for delivery of the repaired

or replaced product back to the original consumer.

This warranty does not apply to any ampliers determined by Wilson Electronics

to have been subjected to misuse, abuse, neglect, or mishandling that alters or

damages physical or electronic properties.

RMA numbers may be obtained by phoning Technical Support at 866-294-1660.

The Manufacturer’s rated output power of this equipment is for single carrier operation.

For situations when multiple carrier signals are present, the rating would have to be

reduced by 3.5 dB, especially where the output signal is re-radiated and can cause

interference to adjacent band users. This power reduction is to be by means of input power

or gain reduction and not by an attenuator at the output of the device.

Operation is subject to the following two conditions: (1) This device may not cause

interference, and (2) this device must accept any interference, including interference that

may cause undesired operation of this device.

Disclaimer: The information provided by Wilson Electronics, Inc. is believed to

be complete and accurate. However, no responsibility is assumed by Wilson

Electronics, Inc. for any business or personal losses arising from its use, or for

any infringements of patents or other rights of third parties that may result from

its use.

3301 East Deseret Drive, St. George UT 84790

For additional Technical Support visit

www.wilsonelectronics.com

Phone: 866-294-1660 Fax: 435-656-2432

Wilson

Electronics, Inc.

Installation Instructions for the Following Wilson Ampliers:

In-Building Wireless Cellular Smart Technology™ 50 dB Amplier

Model # 801105, Part # 801107, Part # 801108

FCC ID: PWO8011SB IC: 4726A-8011SB

In-Building Wireless Cellular Smart Technology™ 60 dB Amplier

Model # 801106, Part # 801109, Part # 801110

FCC ID: PWO8011SB IC: 4726A-8011SB

In-Building Wireless PCS Smart Technology™ 60 dB Amplier

Model # 801306

FCC ID: PWO8013SB IC: 4726A-8013SB

In-Building Wireless iDEN Smart Technology™ 50 dB Amplier

Model # 804005

FCC ID: PWO8040SB IC: 4726A-8040SB

In-Building Wireless iDEN Smart Technology™ 60 dB Amplier

Model # 804006

FCC ID: PWO8040SB IC: 4726A-8040SB

The term “IC” before the radio certication number only signies that Industry

Canada technical specications were met.

A 13 dB 800 MHz Yagi Cellular Antenna (301111)

B 1900 MHz Yagi PCS Antenna (301124)

C 800 MHz Yagi Cellular Antenna (301129)

D Dual-Band Panel Antenna (301135)

E Dual-Polarity Dome Antenna (301123)

F Dual-Band Dome Antenna (301121)

G Low Prole Cellular Antenna (301106)

H Amplier Soft Cases

I Amplier Hard Kit Cases

Antenna Options & Accessories

D E

F G

Before Getting Started

This guide will help you properly install Wilson’s In-Building Wireless Smart

Technology™ Ampliers. It is important to read through all of the installation

steps for your particular application prior to installing any equipment. Read

through the instructions, visualize where all the equipment will need to be installed

and do a soft installation before mounting any equipment. If you do not understand

the instructions in full, seek professional help, or contact Wilson Technical Support at

866-294-1660.

Inside this Package

• In-building wireless amplier

• AC/DC 110 volt power supply

Additional Required Equipment (sold separately)

• Outside Yagi antenna

• Inside dome, panel or low-prole antenna

• Antenna coax cable

How it Works

Wilson ampliers are small, portable, bi-directional devices that deliver service levels

consistent with what would be expected in areas of high cell network coverage. They

amplify a weak or shadowed signal in mobile, marine and in-building applications.

When using a Wilson amplier in conjunction with Wilson antennas, the outside

antenna will collect the cell tower signal and send it through the cable to the

amplier. The signal is then amplied and broadcast from the inside antenna

to the surrounding area. Cell phones and cellular data cards in that area then

communicate with the improved signal. When a cell phone or cellular device

transmits, the signal is received by the inside antenna, amplied by the amplier

and broadcast back to the cell tower through the outside antenna.

In-building wireless

amplier

DC plug-in power

supply

Installation Overview

The following steps provide a summary of the amplier/antenna installation

process. However, they are not a substitute for the complete installation

instructions on the following pages, which you should read thoroughly. Contact

Wilson’s Technical Support Department with any questions at 866-294-1660.

STEP 1 Install the Outside Antenna

Mount the Yagi antenna so that it points toward the cell site and away from where

the inside antenna will be located. Depending on your amplier model, the two

antennas will need 40-65 feet of separation. (See illustrations on pages 5 and 7.)

STEP 2 Install the Inside Antenna

Select a location in the center of where the signal needs to be amplied. Refer

to the instructions included with the inside antenna. (See illustration on page 6 to

determine the inside antenna model that best meets your specic needs.)

STEP 3 Install the Amplier

Position the amplier in a well-ventilated location near a power outlet. Attach the

outside and inside antennas to the amplier using 9913 or equivalent coax cable

(available from Wilson Electronics).

STEP 4 Power up the Amplier

IMPORTANT! Before connecting the power supply, ensure that both the inside

and outside antenna cables are connected. Also ensure that all cell phones and

cellular data cards within 50 feet of the inside antenna are turned off. Plug in the

supplied 6-volt power supply into the amplier and then into a wall outlet.

STEP 5 Check the Amplier Lights

The PWR light should be green, indicating that the amplier has power. If all

other lights are also green, the amplier is operating properly; however, if you do

not have the desired signal coverage area, refer to pages 5, 6, 9 and 10. (Note: if

you are using an outdoor Yagi antenna, it must be adjusted for maximum signal.)

STEP 6 If All Lights are Green Except Light D…

This indicates the combination of outside signals is too strong. Turn the outside

antenna slightly away from the cell site until all lights are green.

STEP 7 If Light A is Amber…

An amber light in the A position indicates the amplier is working but at reduced

gain due to oscillation. If you are satised with the signal coverage, no action

is necessary. If not, increase the separation between the inside and outside

antennas, then unplug the power supply and plug it back in to reset the amplier.

If you still have an amber light, repeat the procedure. (See “Troubleshooting” on

page 10.)

STEP 8 If Light A is Red…

A red light in the A position indicates the amplier has shut down, due either to

oscillation or to cell phone overload. (See “Troubleshooting” and “Cell Phone

Overload Protection” on pages 10 and 11.)

Select a location on the roof of the

building to install the outside antenna,

using a cell phone in test mode to nd

the strongest signal from the cell tower.

For test mode help, visit www.wilsonelectronics.com

or call Technical Support at 866-294-1660.

Installing a Wilson Outside Antenna

Follow the specic antenna

installation instructions included with

the outside antenna.

Lightning protection is recommended

for all in-building installations. Take

extreme care to ensure neither you

nor the antenna come in contact with

any electrical power lines.

A Yagi antenna must be installed

horizontally with the elements vertical

and the drip hole on the bottom.

Ensure there are three feet of

clearance in all directions surrounding

the antenna.

CORRECT

Cell Tower RF Signal

Yagi External Antenna

Warning: The outside antenna must

be installed on an outdoor permanent structure

with a separation of at least 20 feet from all

persons during normal operation.

NOT

CORRECT

Warning: Never point the

front of the Yagi antenna toward

the inside antenna - oscillation will

result, causing amber light and gain

reduction.

Pointing toward

cell tower

Installing a Wilson Inside Antenna

Select a suitable location for the inside antenna, preferably in the center of where

the signal needs to be amplied. To determine signal strength and coverage

distance, refer to page 11 of this installation guide.

Follow the specic antenna installation instructions included with the inside antenna.

Wilson has several inside antenna options. The dome and panel antennas are

the most popular for in-building applications.

For a square room, a dome antenna will provide better coverage. (A)

For a rectangular room, a panel antenna will provide better coverage. (B)

In some cases, multiple inside antennas may be required (C & D). A signal may

be “split” by using a splitter. If using more than one inside antenna, a separation

of at least 20 feet is necessary between inside antennas.

= Dome Antenna

= Panel Antenna = Splitter

= Amplifier

Connect the coax cable from the amplier to the inside antenna. For distances of 20

feet or more, use 9913 coax cable or equivalent to prevent signicant signal loss.

Warning: An inside antenna must have

a separation distance from all persons that is at

least 12 inches for the 5.2 dBi dome antenna

and 15 inches for the 7 dBi panel antenna.

Installing a Wilson Amplier

Select a location to install the amplier that is away from excessive heat, direct

sunlight, moisture and that has proper ventilation. Do not place the amplier in

an air-tight enclosure.

Recommended installation locations for in-building ampliers are:

• On a wall

• On the ceiling

• Near a power outlet

Run the outside antenna cable to the amplier and attach it to the N-Female

connector labeled “outside antenna” on the amplier. Run the inside antenna

cable to the amplier and attach it to the N-Female connector labeled “inside

antenna” on the amplier.

Note: Be careful when plugging the connector in so as not to damage the center

pins on the connectors.

Connect the outside antenna to the amplier with 9913 or equivalent coax cable

(available from Wilson Electronics). Place the inside antenna in the center of

the area needing the amplied signal. It is important to have at least 40 feet of

separation between the inside and outside antennas for the 50 dB ampliers, 50

feet of separation distance for the 60 dB PCS ampliers, and at least 65 feet of

separation distance for the 60 dB cellular ampliers.

AC/DC

Power Supply

Amplifier

Cell

Site

Supports

Multiple

Users

Inside Antenna

Optional Dome

Antenna Shown

Point Yagi antenna

away from inside

antenna

Outside

Antenna

1900 MHz Yagi

Antenna Shown

40 feet minimum

separation between inside

and outside antenna for

50 dB cellular amplifier

50 feet for 60 dB PCS amplifier

65 feet for 60 dB cellular

amplifier

Antenna Separation

Warning: Connecting the

amplier directly to the cell phone

with use of an adapter will damage

the cell phone.

Powering up a Wilson Amplier

1. IMPORTANT! Ensure that all cell phones and cellular data cards within 50 feet

of the inside antenna are turned off.

2. To verify proper installation of the amplier and antennas, make sure that the

distance between the inside and outside antennas is a minimum of 40 feet for

the 50 dB amplier, 50 feet of separation distance for the 60 dB PCS amplier,

and 65 feet for the 60 dB cellular amplier.

3. If you are using an outside Yagi antenna, never point the front of the Yagi

toward the inside antenna.

4. Ensure that both the outside antenna coax cable and the inside antenna coax

cable are connected to the amplier before powering up the amplier.

5. Plug the 6-volt power supply into the amplier input marked “power” (carefully,

to avoid damaging the center pin) and then into a wall outlet.

Warning: Verify that both the

outside antenna and the inside

antenna are connected to the amplier

before powering up the amplier.

Warning: Use only the power

supply provided in this package.

Use of a non-Wilson product may

damage your equipment.

NOTE: The aluminum casing of a Wilson amplier will adjust very quickly to the

ambient temperature of its environment. For example, in the summer, when

the attic of a house can easily exceed 100 degrees Fahrenheit, the amplier

temperature may be 10 or more degrees higher. The casing will be hot to the

touch. Such high temperatures will not damage the amplier, nor do they pose

a re risk. As recommended in these instructions, install the amplier in a

location with adequate ventilation. Keep the area free of items that could block

air ow to the amplier.

Understanding the Amplier Lights

The amplier is equipped with sensitive electronics designed to detect amplier

oscillation or cell phone overload, both of which can hamper amplier performance.

The amplier is designed to automatically reduce gain or, if necessary, shut down

to prevent or compensate for these conditions. Oscillation or overload can be

caused by improper equipment installation -- understanding the amplier lights will

help you identify and solve potential problems.

The power light will turn green when the

amplier is initially powered on.

When all lights are green, the amplier

is working at proper gain level (peak

performance).

If lights A, B and C are green but D is out,

the combination of outside signals is too

strong and the amplier is powering down.

To remedy this, turn the outside antenna

slightly away from the cell site until all

lights are green.

If light A is amber, lights B and C are

green, and light D is off, the amplier

has reduced its gain by 10 dB due

to oscillation. Similar to placing a

microphone next to a speaker with an

audio amplier, placing the inside and

outside antennas too close to each other

will cause oscillation. In such a case,

although the amplier is still working

at reduced gain, the antennas need

more separation for optimal amplier

performance. See “Troubleshooting” on

page 10.

If light A is amber, light B is green, and

lights C and D are off, the amplier

has reduced its gain by 20 dB due to

oscillation. As above, the amplier is

still working at reduced gain, but the

inside and outside antennas need more

separation for optimal performance. See

“Troubleshooting” on page 10.

If light A is red, the amplier has shut

down, due either to oscillation or to cell

phone overload. See “Troubleshooting” on

page 10.

PWR A B C D

Otros manuales para 801105

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de Wilson Electronics

Wilson Electronics

Wilson Electronics Smart Technology 801201-A Manual de usuario

Wilson Electronics

Wilson Electronics BD800AM Manual de usuario

Wilson Electronics

Wilson Electronics 271245 Manual de usuario

Wilson Electronics

Wilson Electronics PRO 710i Manual de usuario

Wilson Electronics

Wilson Electronics 814001 Manual de usuario

Wilson Electronics

Wilson Electronics 271247-50 Manual de usuario

Wilson Electronics

Wilson Electronics SIGNALBOOST MobilePro Manual de usuario

Wilson Electronics

Wilson Electronics 271245 Manual de usuario

Wilson Electronics

Wilson Electronics IoT 5-Band Manual de usuario

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300R Manual de usuario

Wilson Electronics

Wilson Electronics PRO 710i Manual de usuario

Wilson Electronics

Wilson Electronics 801102 Manual de usuario

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300 Manual de usuario

Wilson Electronics

Wilson Electronics 271245 Manual de usuario

Wilson Electronics

Wilson Electronics 801230 Manual de usuario

Wilson Electronics

Wilson Electronics 271220 Manual de usuario

Wilson Electronics

Wilson Electronics 2B1401 Manual de usuario

Wilson Electronics

Wilson Electronics BD800AM-M Manual de usuario

Wilson Electronics

Wilson Electronics 801306 Manual de usuario

Wilson Electronics

Wilson Electronics iDEN Manual de usuario

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manual de usuario

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manual de usuario

Wilson Electronics

Wilson Electronics 271247-75 Manual de usuario

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario