Williams Sound WIR 125 Guía

Williams Sound

Helping People Hear



MANUAL AND USER GUIDE

SoundPlus™Infrared System

Model WIR 125

Transmitter Model WIR TX295

Receiver Model WIR RX3

Williams Sound

Helping People Hear



CONTENTS PAGE

System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System Components . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Recycling Instructions . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . 6

WIR TX295 Transmitter . . . . . . . . . . . . . . . . 6

WIRRX3Receiver ....................8

In Case of Difficulty . . . . . . . . . . . . . . . . . . . . . . . . 9

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

System Specifications . . . . . . . . . . . . . . . . . . . . . . 12

YSTEM

VERVIEW

Thank you for purchasing the WIR 125 Infrared System from

Williams Sound Corp. Anyone needing auditory assistance to over-

come background noise, reverberation, or distance from the sound

source can benefit from the WIR 125.

You can use the WIR 125 for listening to the TV or other audio equip-

ment, or for hearing assistance in coference rooms. You can also use

your RX3 Receiver in most facilities which have an infrared trans-

mitter operating on 95 kHz, such as theaters, cinemas, or churches.

NOTE: The WIR 125 Infrared System is not recomended for use

with a PLASMA TV MONITOR.

If you have problems at anytime with the WIR 125, do not hes-

itate to call us toll-free at 1-800-843-3544.

YSTEM

OMPONENTS

Williams Sound

Helping People Hear



•WIR RX3 Receiver

•9V Battery

•Earphone

• WIR TX295 Transmitter

•Power Supply

•TV Microphone

(MIC 084)

•1m Audio Cable with

dual RCA plugs (WCA 078)

Williams Sound

Helping People Hear



SAFETY INFORMATION

Hearing Safety:

CAUTION!

This product is designed to amplify sounds to a high volume level

which could potentially cause hearing damage if used improperly.

To protect your hearing and the hearing of others:

1. Make sure the volume is turned down before putting on the ear-

phone or headphone before adjusting the volume to a comfortable

level.

2. Set the volume level at the minimum setting that you need to hear.

3. If you experience feedback (a squealing or howling sound), reduce

the volume setting and move the microphone away from the ear-

phone or headphone.

4. Do not allow children or other unauthorized persons to have

access to this product.

Battery Safety and Disposal:

CAUTION!

This product is supplied with disposable Alkaline batteries. Do

not attempt to recharge disposable batteries, which may explode,

release dangerous chemicals, cause burns, or other serious harm

to the user or product.

Williams Sound

Helping People Hear



Pacemaker Safety:

CAUTION!

1. Before using this product with a pacemaker or other medical device,

consult your physician or the manufacturer of your pacemaker or other

medical device.

2. If you have a pacemaker or other medical device, make sure that you

are using this product in accordance with safety guidelines established

by your physician or the pacemaker manufacturer.

RECYCLING INSTRUCTIONS

Help Williams Sound protect the environment! Please take the

time to dispose of your equipment properly.

Product Recycling for Customers in the European Union:

Please do NOT dispose of your Williams Sound equipment in

the household trash. Please take the equipment to an electronics

recycling center; OR, return the product to the factory for proper

disposal.

BatteryRecycling for Customers in the European Union:

Please do NOT dispose of used batteries in the household trash.

Please take the batteries to a retail or community collection point

for recycling.

8/11/05

Williams Sound

Helping People Hear



ETTING UP THE

TX295 T

RANSMITTER

The WIR TX295 Transmitter may be placed on top of a TV or

shelf. Place the TX295 Transmitter where it is clearly visible from

your listening position.

Infrared light behaves like visible light, so it is blocked by solid

objects. This confines the signal to the room where the transmitter

is located. The Transmitter cannot be placed inside or behind any-

thing except glass. The maximum operating distance is approxi-

mately 30 feet (9 m).

Ideally, the TX295 Transmitter should be at ear-level height or

above. The infrared light pattern is much like a floodlight “cone”

as it leaves the transmitter, with the best reception inside the cone.

Sunlight can cause infrared interference in the form of a buzz,

hiss, or static. Thus, the system cannot be used outdoors and may

not work properly inside if a lot of direct sunlight is present.

Closing drapes or blinds will help if sunlight is a problem.

Any number of receivers may be used with the TX295

Transmitter, but use only one transmitter in a room at the same

time. Otherwise, interference will occur.

Receiver

Charging 

Indicator

Right

Battery

Charging

Indicator

Left

Battery

Charging

Indicator

Infrared

Transmitting

Diodes

Infrared

Transmitting 

Diodes

(only for WIR 

RX95 Receiver)

RX95 Receiver Charging Cradle (not used in this system)

BAT AP97A

Battery

Charging Port

(not used in

this system)

BAT AP97A

Battery

Charging Port

(not used in

this system)

Williams Sound

Helping People Hear



STEP 1: CONNECT THE TRANSMITTER POWER SUPPLY

Plug the Power Supply cord into the “DC 12V” jack on the back of

the TX295. Then plug the Power Supply into an AC outlet.

STEP 2: SELECT AN OPERATING FREQUNCY FOR THE TX295 TRANSMITTER

To use the TX295 transmitter with the RX3 receiver, you must

first setup the transmitter to operate in 95 kHz mode. Referring to

the diagram above, slide the Stereo/Mono Selection Switch to the

“L” Left position for 95 kHz. The transmitter is now setup to

operate with the RX3 receiver.

STEP 3: CONNECT THE TRANSMITTER TO THE AUDIO SOURCE

If you are using the TV Microphone, plug it into the “Mic” jack

on the TX295 as shown. Use the Velcro strip supplied to attach the

microphone near the loudspeaker of your TV. The microphone will

allow you to play the TV at lower volume for other listeners and

will pick up other important sounds like the telephone or doorbell

ringing.

To use the supplied Audio Cable to connect the TX295 Transmitter

directly to TV, VCR, or other equipment output jacks:

Connect the LEFT RCA plug from the TV (or VCR) speaker

output into the LEFT RCA jack on the TX295 transmitter.

Remember,the Stereo/Mono Selection Switch must be in the

“L” Left position to transmit in 95 kHz!

When the Audio Inputs are used, the Mic input is automatically

disabled.

NOTE: The TX295 has an automatic shut-off feature that turns

the Transmitter off 90 seconds after the audio signal is no longer

present.

Power

Input ST = Stereo mode

L = 95 kHz mode

R = 250 kHz mode

Stereo/Mono Switch RCA Jack (connect from TV speaker output).

STEREO: Use both RIGHT and LEFT jack.

95 kHz or 250 kHz: Use LEFT jack only.

Mic

Jack

DC12V

L MIC

ST L R

ETTING UP THE

WIR RX3 R

ECEIVER

1. INSTALL THE RECEIVER BATTERIES

Open the Battery Compartment on the RX3 Receiver and install a

9V carbon zinc battery. Be sure to insert the battery “plus” and

“minus” terminals correctly as shown on the yellow battery pull

tab. DO NOT force the battery in backwards. If you are using a

rechargeable, NiMH battery, charge the battery for 12–14 hours

before using the receiver.

Make sure the Receiver Volume Control Switch (Shown in fig-

ure below) is turned OFF while charging.

2. PLUG IN THE EARPHONE OR HEADPHONE.

Next, plug the earphone or headphone into the jack on top of the

receiver

3. USING THE RECEIVER

Rotate the Receiver Volume Control to turn the receiver on and

adjust the volume to a comfortable level. Make sure your TV or

audio source is turned on. You should be able to hear the signal

from the Transmitter in the Receiver. The infrared receiver “eye”

is located on the front of the RX3. Do not cover it up or you will

lose reception.

Be sureto turn the Receiver OFF when it is not in use.

Williams

Sound

Volume 

Control

& Switch

Earphone 

Jack

Infrared

"Eye"

ASE OF

IFFICULTY

If the system does not seem to be functioning:

1. Read through the manual and user guide carefully to verify

proper setup and installation of your system.

2. Make sure that your television is plugged in and turned on.

3. Make sure that the TX295 Transmitter is plugged in and cor-

rectly connected to the TV or VCR’s audio output.

4. Make sure the TX295 is operating on 95 kHz, not stereo or 250

kHz mode. See Step 2 in Setting up the TX295 Transmitter.

5. If you’re using the TV Mic and not getting a signal: 1) Be sure

the audio cable is not plugged into the TX295; 2) Try turning

the TV volume up slightly; 3) Try positioning the TV mic

directly over the TV speaker.

6. Make sure that the RX3 Receiver has a working battery.

7. Make sure you are not covering the RX3’s infrared "eye.”

Remove any objects obstructing the line between the TX295

Transmitter and the RX3 Receiver.

8. If you’ve installed the TX295 Transmitter other than on

top of the TV, make sure that its front panel is facing the

RX3 Receiver.

9. If the system still does not function, call Williams Sound

Product Service at

1-800-843-3544.

Williams Sound

Helping People Hear



Williams Sound

Helping People Hear



LIMITED WARRANTY

Williams Sound products are engineered, designed and manufactured

under carefully controlled conditions to provide you with many years

of reliable service. Williams Sound warrants the SOUNDPLUS™

Infrared System against defects in materials and workmanship for

FIVE (5) years. During the first five years from the purchase date, we

will promptly repair or replace the SoundPlus™Infrared System.

Microphones, earphones, headphones, batteries, chargers, cables, carry

cases, and all other accessory products carry a 90-day warranty.

WILLIAMS SOUND HAS NO CONTROL OVER THE CONDI-

TIONS UNDER WHICH THIS PRODUCT IS USED. WILLIAMS

SOUND, THEREFORE, DISCLAIMS ALL WARRANTIES NOT

SET FORTH ABOVE, BOTH EXPRESS AND IMPLIED, WITH

RESPECT TO THE SOUNDPLUS™INFRARED SYSTEM,

INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRAN-

TY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. WILLIAMS SOUND SHALL NOT BE LIABLE TO

ANY PERSON OR ENTITY FOR ANY MEDICAL EXPENSES OR

ANY DIRECT,INCIDENTAL OR CONSEQUENTIAL DAMAGES

CAUSED BY ANY USE, DEFECT, FAILURE OR MALFUNCTION

OF THE PRODUCT, WHETHER A CLAIM FOR SUCH DAMAGES

IS BASED UPON WARRANTY, CONTRACT, TORT OR OTHER-

WISE. THE SOLE REMEDY FOR ANY DEFECT, FAILURE OR

MALFUNCTION OF THE PRODUCT IS REPLACEMENT OF THE

PRODUCT. NO PERSON HAS ANY AUTHORITY TO BIND

WILLIAMS SOUND TO ANY REPRESENTATION OR WARRAN-

TY WITH RESPECT TO THE SOUNDPLUS™INFRARED

SYSTEM. UNAUTHORIZED REPAIRS OR MODIFICATIONS

WILL VOID THE WARRANTY.

The exclusions and limitations set out above are not intended to, and

should not be construed so as to contravene mandatory provisions of

applicable law.If any part or term of this Disclaimer of Warranty is

held to be illegal, unenforceable or in conflict with applicable law by

acourt of competent jurisdiction, the validity of the remaining por-

tions of this Disclaimer of Warranty shall not be affected, and all

rights and obligations shall be construed and enforced as if this

Limited Warranty did not contain the particular part or term held to be

invalid.

Tabla de contenidos

Otros manuales de Receptor de Williams Sound

Williams Sound

Williams Sound PPA VP 37 Guía

Williams Sound

Williams Sound Hearing Helper PFM R31 Manual de usuario

Williams Sound

Williams Sound T2 863 Manual de usuario

Williams Sound

Williams Sound Personal P.A. T18 Manual de usuario

Williams Sound

Williams Sound DLR 60 2.0 Manual de usuario

Williams Sound

Williams Sound SoundPlus WIR RX15-2 Manual del operador

Williams Sound

Williams Sound PPA R751 Manual de usuario

Williams Sound

Williams Sound PPA R37 Manual de usuario

Williams Sound

Williams Sound TGS PRO 737 Guía

Williams Sound

Williams Sound SoundPlus Infrared System WIRTX900 Manual de usuario

Williams Sound

Williams Sound SoundPlus WIR RX22-4 Instrucciones de montaje

Williams Sound

Williams Sound WIR RX14 Instrucciones de montaje

Williams Sound

Williams Sound SoundPlus Infrared Receiver WIR RX238 Manual de usuario

Williams Sound

Williams Sound WaveCAST WF T5 Manual de usuario

Williams Sound

Williams Sound Personal PA R35 Instrucciones de montaje

Williams Sound

Williams Sound DLR 360 Manual de usuario

Williams Sound

Williams Sound Whisper R863 Manual de usuario

Williams Sound

Williams Sound R801 Guía de solución de problemas

Williams Sound

Williams Sound Digi-Wave DLR 400 ALK Manual de usuario

Williams Sound

Williams Sound FM Listening System PPA 575 Manual de usuario

Williams Sound

Williams Sound PPA R38 Manual de usuario

Williams Sound

Williams Sound SoundPlus Infrared Receiver WIR RX12-4 Manual de usuario

Williams Sound

Williams Sound PPA VP Manual de usuario

Williams Sound

Williams Sound IR?RX20 Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario