WIKA GA11 Manual de usuario

Operating instructions

Betriebsanleitung

Mode d‘emploi

Manual de instrucciones

Analysegerät zur Ermittlung der Gasqualität

von Isoliergasen, Typ GA11

Analytic instrument for N2gas

Analytic instrument for determining the quality

of insulated gases, model GA11

Analizador para determinar la calidad del gas

aislante, modello GA11

Instrument d‘analyse pour déterminer la

qualité du gaz isolants , type GA11

14395193.01 07/2020 EN/DE/FR/ES

WIKA operating instructions analytic instrument, model GA11

WIKA®is a registered trademark in various countries.

WIKA®ist eine geschützte Marke in verschiedenen Ländern.

Prior to starting any work, read the operating instructions!

Keep for later use!

Vor Beginn aller Arbeiten Betriebsanleitung lesen!

Zum späteren Gebrauch aufbewahren!

Lire le mode d'emploi avant de commencer toute opération !

A conserver pour une utilisation ultérieure !

¡Leer el manual de instrucciones antes de comenzar cualquier trabajo!

¡Guardar el manual para una eventual consulta!

Betriebsanleitung Typ GA11 Seite 39 - 74

Operating instructions model GA11 Page 3 - 38

Manual de instrucciones modello GA11 Página 111 - 145

Mode d‘emploi type GA11 Page 75 - 110

3WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

Contents

1. General information 5

2. Design and function 6

2.1 Overview. . . . . . . . . . . . . . . . . . . . . . . .6

2.2 Description . . . . . . . . . . . . . . . . . . . . . . .7

2.3 Scope of delivery . . . . . . . . . . . . . . . . . . . . .8

3. Safety 8

3.1 Intended use . . . . . . . . . . . . . . . . . . . . . .8

3.2 Personnel qualification . . . . . . . . . . . . . . . . . . 10

3.3 Personal protective equipment . . . . . . . . . . . . . . . 10

3.4 Handling of insulating gases and gas mixtures . . . . . . . . . . 11

3.5 Valid standards and directives . . . . . . . . . . . . . . . 12

3.6 Dealing with pressure-retaining components . . . . . . . . . . 13

3.7 Residual risks . . . . . . . . . . . . . . . . . . . . . 13

3.8 Labelling, safety marks . . . . . . . . . . . . . . . . . . 13

4. Transport, packaging and storage 14

4.1 Transport. . . . . . . . . . . . . . . . . . . . . . . 14

4.2 Packaging . . . . . . . . . . . . . . . . . . . . . . 14

4.3 Storage . . . . . . . . . . . . . . . . . . . . . . . 14

5. Commissioning, operation 14

5.1 Battery/mains operated . . . . . . . . . . . . . . . . . . 14

5.2 Connecting the gas compartment . . . . . . . . . . . . . . 15

5.2.1 Pumping back in the measured gas compartment . . . . . . . 15

5.2.2 Pumping back in external gas compartment (pressurised) . . . . 16

5.2.3 Pumping back in external gas compartment (depressurised) . . . 16

5.3 Switching on and off . . . . . . . . . . . . . . . . . . . 16

5.4 Performing measurements. . . . . . . . . . . . . . . . . 17

5.5 Cancelling an ongoing measurement . . . . . . . . . . . . . 20

5.6 Emptying depot and depressurised gas compartment . . . . . . . 21

5.7 Saving the measuring result . . . . . . . . . . . . . . . . 22

5.8 Managing the saved measuring results . . . . . . . . . . . . 22

5.8.1 Internal memory . . . . . . . . . . . . . . . . . . 22

6. Settings 24

6.1 Calling the settings mode . . . . . . . . . . . . . . . . . 24

6.2 Settings . . . . . . . . . . . . . . . . . . . . . . . 24

6.3 System . . . . . . . . . . . . . . . . . . . . . . . 25

6.4 Evacuating the system . . . . . . . . . . . . . . . . . . 25

6.5 Importing/exporting the list of measurement names via USB interface . . 27

6.6 Limit values for gases . . . . . . . . . . . . . . . . . . 28

6.7 Firmware upgrade. . . . . . . . . . . . . . . . . . . . 29

4WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

Contents

Declarations of conformity can be found online at www.wika.com.

7. Maintenance and cleaning 30

7.1 Maintenance . . . . . . . . . . . . . . . . . . . . . 30

7.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . 30

7.3 Recalibration . . . . . . . . . . . . . . . . . . . . . 30

8. Replacing sensors 31

9. Faults 33

10. Dismounting, return and disposal 34

10.1 Dismounting . . . . . . . . . . . . . . . . . . . . . 34

10.2 Return . . . . . . . . . . . . . . . . . . . . . . . 34

10.3 Disposal . . . . . . . . . . . . . . . . . . . . . . 35

11. Specifications 36

12. Accessories 37

5WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

1. General information

■

The analytic instrument described in the operating instructions has been designed

and manufactured using state-of-the-art technology.

All components are subject to stringent quality and environmental criteria during

production. Our management systems are certied to ISO 9001 and ISO 14001.

■

These operating instructions contain important information on handling the

instrument.Working safely requires that all safety instructions and work instructions

are observed.

■

Observe the relevant local accident prevention regulations and general safety

regulations for the instrument's range of use.

■

The operating instructions are part of the product and must be kept in the immediate

vicinity of the instrument and readily accessible to skilled personnel at any time.

■

Skilled personnel must have carefully read and understood the operating instructions

prior to beginning any work.

■

The manufacturer's liability is void in the case of any damage caused by using

the product contrary to its intended use, non-compliance with these operating

instructions, assignment of insuciently qualied skilled personnel or unauthorised

modications to the instrument.

■

The general terms and conditions contained in the sales documentation shall apply.

■

Subject to technical modications.

■

Factory calibrations/DKD/DAkkS calibrations are carried out in accordance with

international standards.

■

Further information:

- Internet address: www.wika.de

- Relevant data sheet: SP 62.11

- Application consultant: Tel.: +49 9372 132-8971

info@wika.com

6WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

2. Design and function

2.1 Overview



















 

Power supply unit

Adapters

Storage for hoses

Storage for power cord

User interface

ON/OFF key

Touchscreen

Network connection (LAN)

Inlet, return pumps

Outlet, gas cylinder

Power and charging

indicators

Outlet for gas recovery bag

USB interface

Power connection

7WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

2. Design and function

2.2 Description

Data processing and data storage

The analytic instrument model GA11 is a multi-sensor system for examining the quality

of N2 / CleanAir / DryAir, e.g. in switchgear.The basic instrument consists of a built-in

computer with touchscreen for processing and storage of up to 500 data records.The

data records can be exported via the integrated USB interface.

Extendable sensor system

The sensor system of GA11 is module-based and can be extended. In addition, there

is the possibility of storing measuring gas internally as well as pumping it back into the

original gas compartment without losses after the measurement.

Automatic adjustment of the gas quality

After the measurement, the results will be compared with customer-specically

adjustable limit values according to e.g. CIGRE B3.02.01 or IEC 60480 standards.The

operator thus obtains a reliable statement on whether the insulating gas is suitable for

the given application or not, or whether it is necessary to perform a gas processing or

a gas exchange. For gas mixtures based on N2 / CleanAir / DryAir, there might not yet

be any standards or limit values available. It is recommended that, before measuring

the gas quality, the requirements and the limit values are veried with the respective

manufacturer.

Battery life

If the lithium-ion rechargeable battery is fully charged, the analytic instrument can

perform at least 5 measurements with the “pumping back” function.The number of the

battery-powered pump-back cycles is largely dependent on the container pressure of the

gas to be measured.

The GA11 sends a warning message on the display when battery is low.

If the instrument is not connected to the mains in time, it will shut down automatically in

order to prevent damages and data loss. In the mains operation, the battery is charged

and the instrument can be switched on again at the same time and operate without

restrictions.

Power and charging indicators

The front control panel has two LEDs which indicate the charging status (red) or mains

operation (green).

If an error occurs during the charge cycle, the charging indicator ashes (red).

8WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

2. Design and function/3. Safety

2.3 Scope of delivery

■

Analytic instrument model GA11 in a sturdy transport case

■

Power supply unit with power cord

■

Gas emission adapter

■

Calibration certicate

■

Touchpen

■

USB stick

■

Operating instructions

■

See delivery note for optionally ordered sensor system and accessories

Cross-check scope of delivery with delivery note.

3. Safety

Explanation of symbols

WARNING!

... indicates a potentially dangerous situation that can result in serious injury

or death, if not avoided.

CAUTION!

... indicates a potentially dangerous situation that can result in light injuries

or damage to property or the environment, if not avoided.

Information

... points out useful tips, recommendations and information for ecient and

trouble-free operation.

3.1 Intended use

The GA11 is used for determining the gas quality of the following insulating gases and

gas mixtures.

Permissible insulating gases and gas mixtures for N2-Analyser

■

N₂ / CleanAir / DryAir

9WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

3. Safety

Application areas

The instrument is especially designed for applications that full the following conditions:

■

The use is only allowed in buildings or dry surroundings.

■

Use only for commercial purposes and in industrial environment.

■

The height of the operation site should not exceed 2,500 m.

■

Environment with max. pollution degree of 3.

■

Voltage supply of overvoltage category II.

■

Ambient temperature between 0 ... 40 °C.

Only use the analytic instrument in applications that lie within its technical performance

limits (e.g. max. ambient temperature, pressure ranges, ...).

→ Performance limits see chapter 11 “Specications”.

The instrument has been designed and built solely for the intended use described here,

and may only be used accordingly.

Only use the instrument with original accessories from WIKA.

Refrain from unauthorised modications to the instrument.

Any use beyond or dierent to the intended use is considered as improper use.

The technical specications contained in these operating instructions must be

observed. Improper handling or operation of the instrument outside of its technical

specications requires the instrument to be taken out of service immediately and

inspected by an authorised WIKA service engineer.

Handle electronic precision measuring instruments with the required care (protect from

humidity, impacts, strong magnetic elds, static electricity and extreme temperatures,

do not insert any objects into the instrument or its openings). Plugs and sockets must be

protected from contamination.

The manufacturer shall not be liable for claims of any type based on operation contrary

to the intended use.

10 WIKA operating instructions analytic instrument, model GA11

14395193.01 07/2020 EN/DE/FR/ES

3. Safety

3.2 Personnel qualification

WARNING!

Risk of injury should qualication be insucient

Improper handling can result in considerable injury and damage to property.

■

The activities described in these operating instructions may only be

carried out by skilled personnel who have the qualications described

below.

■

Keep unqualied personnel away from hazardous areas.

Trained personnel

The plant operator must ensure that the handling of N2/ CleanAir / DryAir (gas

mixtures) is only carried out by a qualied company or by qualied persons which

have been specially trained in accordance with IEC 62271-4:2013, IEC 60480 and

IEC 60376 section 10.3.1 (as well as the Annexes A and B). In addition, it is imperative

that personnel are familiar with the physical principles of N2/ CleanAir / DryAir

(gas mixtures) and have the specic knowledge to perform gas handling and gas

measurements from IEC 62271-4:2013, ASTM D2029 - 97:2017 and the CIGRÈ - SF₆

Measurement guide (723).

Special operating conditions require further appropriate knowledge, e.g. of aggressive

media (ASTM D2284 – 11).

3.3 Personal protective equipment

The personal protective equipment is designed to protect the skilled personnel from

hazards that could impair their safety or health during work.When carrying out the

various tasks on and with the instrument, the skilled personnel must wear personal

protective equipment.

Follow the instructions displayed in the work area regarding personal protective

equipment!

The requisite personal protective equipment must be provided by the operating

company.

Wear safety goggles!

Safety goggles to EN 166, class 2.

They protect the eyes from ying parts during coupling or releasing of the

quick connections under pressure.

Wear protective gloves!

Protect hands from friction, abrasion, cuts or deep injuries and also from

contact with hot surfaces.

Otros manuales para GA11

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de WIKA

WIKA

WIKA 116.18.02 Series Manual de usuario

WIKA

WIKA DELTA-trans DPGT40 Manual de usuario

WIKA

WIKA Delta-plus Manual de usuario

WIKA

WIKA 1500 Series Manual de usuario

WIKA

WIKA TC82 Instrucciones de funcionamiento

WIKA

WIKA IL-10 Manual de usuario

WIKA

WIKA air2guide A2G-20 Manual de usuario

WIKA

WIKA TR10-B Manual de usuario

WIKA

WIKA DG-10-S Manual de usuario

WIKA

WIKA CTD9300 Series Manual de usuario

WIKA

WIKA FLC-2300 Manual de usuario

WIKA

WIKA TFT35 Manual de usuario

WIKA

WIKA NETRIS 3 Manual de usuario

WIKA

WIKA CPG2300 Series Manual de usuario

WIKA

WIKA DIH50 Manual de usuario

WIKA

WIKA 55 Series Instrucciones de funcionamiento

WIKA

WIKA NS 63 Manual de usuario

WIKA

WIKA GDM-RC-100-T Manual de usuario

WIKA

WIKA 712.15.160 Manual de usuario

WIKA

WIKA FLC-608 Manual de usuario

WIKA

WIKA DI10 Manual de usuario

WIKA

WIKA 7 Series Manual de usuario

WIKA

WIKA GDM-100 Manual de usuario

WIKA

WIKA CEP3000 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario