Wi-Tek WI-PMS310GF-Alien Manual de usuario
WI-PMS310GF-Alien QSG Page 1 of 16
Managed, Auto PoE Switch
WI-PMS310GF-Alien
8GE + 2 SFP
Layer 2 Managed Auto PoE Switch Quick Start Guide
V2108
WI-PMS310GF-Alien QSG Page 2 of 16
Table of Contents
1.
Introduction......................................................................................... 3
2.
Package Contents.............................................................................. 3
3.
System Requirements........................................................................ 3
4.
LEDs................................................................................................... 4
4.1
System LEDs............................................................................................ 4
4.2
RJ45 LEDs ............................................................................................... 4
4.3
SFP LEDs................................................................................................. 4
5.
Front Panel......................................................................................... 5
6.
Configuration ...................................................................................... 6
6.1
Accessing the Configuration Interface...................................................... 6
6.1.1.
Graphical User Interface .................................................................................. 6
6.1.2.
Command Line Interface.................................................................................. 7
6.2
Saving Current Configuration ................................................................... 8
6.3
DHCP IP Address..................................................................................... 9
6.4
Network Time Client Setup..................................................................... 10
6.5
AAA ........................................................................................................ 11
6.5.1.
TACACS+ ...................................................................................................... 11
6.5.2.
802.1x (EAP).................................................................................................. 13
6.6
SNMP and MIBs..................................................................................... 14
7.
Firmware Update.............................................................................. 16
7.1
Update using GUI................................................................................... 16
7.2
Update using TFTP ................................................................................ 16
WI-PMS310GF-Alien QSG Page 3 of 16
1. Introduction
The WI-PMS310GF-Alien is an Auto-PoE, Managed, Layer 2 (L2), POE (24
& 48V) IP Switch, with Gigabit Ethernet (GbE), Small Form-factor Pluggable
(SFP), and serial Console interfaces.
This document supplements the Wi-TeK Managed Industrial PoE
Switch User Manual, available for download from:
http://www.wireless-tek.com/Uploads/download/1583371174.pdf
2. Package Contents
WI-PMS310GF-Alien
3. System Requirements
Web Browser: e.g. Mozilla Firefox, Google Chrome, Safari, Microsoft
Edge, or Microsoft Internet Explorer.
WI-PMS310GF-Alien QSG Page 4 of 16
4. LEDs
4.1 System LEDs
LED State Status
Blinking
(slow)
Normal OperationSYS
Flashing
(Fast)
Initializing (boot up)
PWR On Steady on if power applied
4.2 RJ45 LEDs
LED State Status
Off No Power applied
Green 48 V PoE applied
PoE
Orange 24 V PoE applied
Green 10/100/1000 Mbps connection.
Flashes with activity.
Link
Off No Ethernet connection
4.3 SFP LEDs
LED State Status
Off No link9
10 Green Link established at 1000 Mbps (1 Gbps)
Flashing Indicates Activity
WI-PMS310GF-Alien QSG Page 5 of 16
5. Front Panel
Port Description
Note Active PoE means that PoE voltage is applied only if a device is
connected.
RJ45 1-8 LAN: 10/100/1000 bps Ethernet connection
PoE Out. 2-Pair, Pins: 48V=1,2(+) 3,6 (-), 24V=4,5(+) 7,8 (-)
Software selectable:
•Off
•24 V Active
•48 V Active 802.3af 15 W max
•48 V Active 803.3at 30 W max
•Auto Active, Auto selection Off/24/48V PoE
•24V Forced On
•48V Forced On
SFP 9-10 Hot-swappable Small Form-factor Pluggable (SFP) ports
supporting 1 Gbps connections.
Console This port is compatible with Cisco part number 72-3383-01
(Console Cable). The serial settings are:
Baud rate: 38400
Data bits: 8
Stop bits: 1
Parity: None
Flow control: None
RESET Button to the left of the PWR LED.
To reset the Switch to factory defaults:
The Switch should be running after bootup is complete and the
SYS LED is blinking. Press and hold the Reset button until the
SYS LED starts flashing rapidly. Release the Reset button.
WI-PMS310GF-Alien QSG Page 6 of 16
6. Configuration
This section covers some tasks that are not fully covered in the User Manual
(see section Introduction, page 3).
6.1 Accessing the Configuration Interface
There are two configuration options:
1. Graphical User Interface (GUI), using an Ethernet connection.
2. Command Line Interface (CLI), using a console cable.
6.1.1. Graphical User Interface
For full details, download this document:
http://www.wireless-tek.com/Uploads/download/1583371174.pdf
When in Factory Reset state, the Switch is set to use the default IP address
of 192.168.0.1.
1. Make sure that your host system is connected via Ethernet
to the Switch.
2. Configure the Ethernet adapter on your host system with a
static IP address in the 192.168.0.x subnet.
e.g. 192.168.0.10
3. Launch your web browser and type http://192.168.0.1
in the address field. Press enter (PC) or return (Mac).
WI-PMS310GF-Alien QSG Page 7 of 16
4. Enter the login credentials.
The default credentials are:
Username: admin
Password: admin
6.1.2. Command Line Interface
For full details, download these documents:
•https://ubwh.com.au/documents/WI-TEK_CLI.pdf
•https://ubwh.com.au/documents/WI-TEK_CLI_POE.pdf
(additional CLI commands for POE switches)
See an example session below, with many lines deleted for clarity.
Username:admin
Password:admin
Switch>?
Exec commands:
show Show running system information
Switch>show ?
ip Internet Protocol (IP)
Switch>show ip ?
interface IP interface status and configuration
Switch>show ip interface brief
Interface IP-Address Status Protocol
ge1/1 unassigned up down
WI-PMS310GF-Alien QSG Page 8 of 16
6.2 Saving Current Configuration
Configuration changes are not permanent, unless saved.
To preserve a configuration change to be used on the next boot-up, save the
current configuration using the System Configuration / Save Current
Configuration menu option.
WI-PMS310GF-Alien QSG Page 9 of 16
6.3 DHCP IP Address
These instructions are to configure the device to obtain its network
configuration (IP address, subnet mask, gateway address) from a DHCP
server on the same LAN.
After this has been done, consult the DHCP server’s list of leases to learn the
IP address of the device.
1. Select the IP Basic Configuration / IP Address Configuration
menu selection.
2. Set Line Item to 1
Set DHCP Client to Enable
Click Set IP Address/DHCP Client
3. The Switch will now query the LAN DHCP server and move to a new
IP address. Consult the DHCP server’s list of leases to learn the new
IP address of the Switch.
WI-PMS310GF-Alien QSG Page 10 of 16
6.4 Network Time Client Setup
By default the Simple Network Time Protocol (SNTP) client is disabled. To
enable:
1. Select the System Configuration / SNMP Configuration menu
selection.
2. Set Enable Status to Enable,
Set the Time Zone
Enter one or more of the Server IP addresses shown below.
Click Apply
Tabla de contenidos
Otros manuales de Cambiar de Wi-Tek
Wi-Tek
Wi-Tek WI-PMS310GF-Alien-I Manual de usuario
Wi-Tek
Wi-Tek WI-PCES306G Manual de usuario
Wi-Tek
Wi-Tek WI-PS518GF Manual de usuario
Wi-Tek
Wi-Tek WI-PCMS310GF Manual de usuario
Wi-Tek
Wi-Tek WI-PMS310GF-UPS Manual de usuario
Wi-Tek
Wi-Tek FTTH ONU EQUIPMENT Manual de usuario
Wi-Tek
Wi-Tek WI-PS306GF-I Manual de usuario
