Whirlpool Spatec Lima Especificaciones técnicas

Use and Installation Manual

Freestanding hydromassage

Bathtub

MODEL: Spatec Lima

MEASURES: 1700*800*580mm

1. Installation and instructions

WARNING! Danger from fire, electric shock and water leakage.

Dear customer

Thank you for choosing our product. Please take a few minutes to read this

manual before starings installation.

NOTE! Improper installation, use or maintenance may invalidate the

warranty and cause personal injury or property damage.

2. Content of the package

Thank you for choosing our hydromassage bathtub. Your product has been equipped

with most of the necessary accessories. To save space during transport, some items

have been packed separately. Please take a few minutes to ensure that all

accessories are included.

If an item is missing, please contact the seller.

Accessories box:

The bathtub package contains an additional box with the following items:

1. Drain

2. Drain plug

Installation tools

For the correct installation of the bath, the following tools will be needed:

1. Level

2. Sealer

3. Spanner

4. Destornillador

5. PTFE tape

3. Bathtub components

：

1. Air jets

2. LED spotlight

3. Overflow

4. Drain

5. Control button

Electrical parameters:

●Voltage 220 V

●Nominal frequency 50 Hz

●Maximum power 310 W

●Rated current 1.5 A

Attention! All electrical connections must be made by a certified

electrician in accordance with the requirements of national electrical

codes and procedures.

4. Connection preparation

The following measures are an example. All dimensions required for

proper installation should be taken directly from the product.

Note: The fitting is recommended to be installed in the area marked in blue in the

diagram. We recommend the installation of specífic faucets for freestanding bathtub.

5. Installation

1. As shown in the picture below, turn the tub over, wrap the tub hole with PTFE

tape and then screw in the siphon.

2. Turn the bathtub around. Move the bathtub to the right place in your bathroom;

put the siphon in the drain and seal it. Adjust the feet of the bath so that the

bath is horizontal and level.

3. Carry out the electrical installation, connecting the bathtub with cables of at

least 2.5 mm2 to a socket that has a 16A magnetothermic, 30mA differential

and earthing.

6. Operation

•To turn on the air jets and the LED spotlight, simply press the button on the

edge of the bath.

•To turn off the functions, press the button again.

7. Cleaning and maintenance

1. Use generic liquid detergent and a soft cloth for daily cleaning. Do not use

detergent with acetone, ammonia or strong water.

2. Scale deposits can be cleaned with citric acid or hot vinegar using a soft cloth.

3. Chrome parts do not need to be cleaned frequently.

4. To avoid scratches, do not clean the bath with hard or rough materials.

5. To avoid damage, do not use detergents with chemical solvents.

6. Be sure to drain the water after use.

7. To avoid damage, do not hit the bath with hard or sharp objects.

8. Do not approach the bath with cigarettes or heat sources higher than 70°C.

9. In order to clean the internal air ducts, it is recommended to activate the air pump

for about 10 seconds after each use of the bath without water.

8. PRECAUTIONS

1. Installation must be performed by a qualified technician in accordance with the

requirements of national electrical codes and procedures.

2. There must be a RCCB and MCB in the installation. Make sure the ground wire is

properly installed.

3. Do not use water at a very high temperature. Put the cold water first, then the hot

water. Do not activate the appliance until the water level is higher than the level of the

jets.

4. The nominal voltage of this device is 220V. Do not use the device if the voltage is

higher than 235V or lower than 190V.

5. Do not take too long baths. Recommended time: less than 30 minutes.

6. In the event of occasional system shutdown, restart the device.

7. If the power cable is damaged, it must be replaced by the manufacturer, or by

qualified persons in order to avoid unnecessary risks.

8. This manual is enclosed with the product. Before installation, please read it

carefully. Installation and use must be in accordance with this manual to avoid damage

or accidents.

Tabla de contenidos

Otros manuales de Producto de plomería de Whirlpool

Whirlpool

Whirlpool SinkSpa LJD1306L Manual de usuario

Whirlpool

Whirlpool JETTED SINK Manual de usuario

Whirlpool

Whirlpool UW8 F2Y WBI F Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario