Wenglor ODX402P0088 Manual de usuario

ODX402P0088

ODX402P0099

Fiber Optic Cable Sensor

Operating Instructions

Translation of the Original Operating Instruction

Subject to change without notice

Available as PDF version only

Status: 07.11.2017

www.wenglor.com

2Table of contents

Table of contents

1. Proper Use 3

2. Safety Precautions 3

3. General Information Regarding the Product 3

4. Product Features 4

4.1. Connection Diagrams 4

4.2. Housing Dimensions 4

4.3. EU Declaration of Conformity 5

4.4.Technical Data 5

4.5. Contamination Output 6

4.6. Complementary Products (see catalog) 6

4.7. Control Panel 6

4.8. Installation Instructions 7

4.8.1 Mounting to a DIN rail 7

4.8.2 Side mounting 8

4.8.3 Connecting the plastic fibre-optic cable 8

5. Initial Start-Up 9

5.1. Overview of functions 9

5.2. Menu Structure 10

6. Settings 11

6.1. Run 11

6.2. Sensors 11

6.2.1 Teach-In 11

6.2.2 Configuring the Operating Mode 13

6.2.3 Set filter 13

6.2.4 Reset 14

6.3. Output 14

6.3.1 Configuring the Output 14

6.3.2 Link the outputs 15

6.3.3 ON-/OFF-Delay 16

6.4. Measure 16

6.5. Display 18

6.6. Language 19

6.7. Information 19

6.8. Reset 19

6.9. Password 20

7. IO-Link 21

8. Add-on Modules 21

8.1. Connect the Add-on Modules 21

8.2. Disconnect the Add-on Modules 21

9. Maintenance Instructions 22

10. Proper Disposal 22

Fiber Optic Cable Sensor

1. Proper Use

This wenglor product is used in accordance with the following mode of operation:

Both plastic fiber optic cables and glass fiber optic cables can be connected to fiber optic cable sensors.

Universal reflex sensors can be used both with and without fiber optic cables. Fiber optic cable sensors ana-

lyze the light reflected by the object. The output switches when an object reaches the selected range (detec-

tion) or when the active light beam is interrupted (operating limits). Bright objects reflect more light than dark

objects, and can thus be recognized from greater distances. In barrier operation, the color of the object has

no effect on the range.

2. Safety Precautions

• This operating instruction is part of the product and must be kept during its entire service life.

• Read this operating instruction carefully before using the product.

• Installation, start-up and maintenance of this product has only to be carried out by trained personnel.

• Tampering with or modifying the product is not permissible.

• Protect the product against contamination during start-up.

• Not a safety component in accordance with the EU Machinery Directive.

3. General Information Regarding the Product

Three wenglor fiber optic cables can be adapted to these Sensors. Up to 12 add-on modules can be con-

nected to this basic module, making 15 fiber optic cables available. The modern OLED display assures easy,

menu-driven Sensor setup. Signal strengths and the switching threshold can be read from the display as

numeric values or as a bar graph. Convenient programming and quick diagnosis is possible via the IO-Link

interface.

4Product Features

4. Product Features

4.1. Connection Diagrams

Plug number 1 Plug number 2 Plug number 3

775

+ Supply Voltage “+”

A/ Switching Output (1, 2, 3…)/IO-Link

A Switching Output (1, 2, 3…)

Contamination Output/Error Output (NC)

– Supply Voltage “0 V”

4.2. Housing Dimensions

ODX402P0088 ODX402P0099

1 =Transmitter Diode

2 =Receiver Diode

Fiber Optic Cable Sensor

4.3. EU Declaration of Conformity

The EU declaration of conformity can be found on our website at www.wenglor.com in download area.

RoHS

4.4.Technical Data

Switching Hysteresis < 15 %

Light Source Red Light

Wave Length 660 nm

Service Life (Tu = 25 °C) 100000 h

max. Ambient Light 10000 Lux

Supply Voltage 18…30 V

Current Consumption (Ub = 24 V) < 70 mA (+10 mA per ODX402P0099)

Switching Frequency 2 kHz

Response Time 250 µs (+70 µs per ODX402P0099)

ON-/OFF-Delay 0…10000 ms

Temperature Drift < 10 %

Temperature Range –25…60 °C

Switching Output Voltage Drop < 2,5 V

Switching Output/Switching Current 100 mA

Short Circuit Protection yes

Reverse Polarity Protection yes

Overload Protection yes

Teach Mode NT, MT, ZT, DT, TP, HT, FT

Adjustment Teach-In

Housing Plastic

Degree of Protection IP50

Connection M12 × 1; 4+8-pin

Protection Class III

DIN-Rail mounting 35 mm

6Product Features

4.5. Contamination Output

The contamination output functions as a normally closed contact (NC) and is switched off as soon as at least

one of the connected sensors is being operated within the unreliable range.

Unreliable range: contamination, misalignment

4.6. Complementary Products (see catalog)

wenglor offers Connection Technology for field wiring.

Suiting Connection Technology No.

S02

S74

Glass Fiber Optic Cable

IO-Link Master

Plastic Fiber Optic Cable

Add-on Module ODX402P0099

4.7. Control Panel

20 = Enter Button

22 = Up Button

23 = Down Button

60 = Display

Fiber Optic Cable Sensor

4.8. Installation Instructions

All applicable electrical and mechanical regulations, standards and safety precautions must be adhered to

when installing and operating the Sensor. The Sensor must be protected against mechanical influences. Install

the device such that its installation position cannot be inadvertently changed.

4.8.1 Mounting to a DIN rail

 

Fig.1 Mounting of the Sensor to a DIN rail



8Product Features

4.8.2 Side mounting

Side mounting a unit: Secure the Sensor with screws (M4) through the mounting holes.

Fig. 2 Side mounting of the Sensor

4.8.3 Connecting the plastic fibre-optic cable

• Please cut the plastic fibre-optic cable once before using with the Z0015 cutting tool.

• Open the mounting slide with a screwdriver (see fig. 3-1)

• Insert the light cable into the opening provided to this end (see fig. 3-2)

• Close the mounting slide (see fig. 3-3)

 

Fig. 3 Connecting the plastic fibre-optic cable

Fiber Optic Cable Sensor

5. Initial Start-Up

Before the configuration, connect plug no. 1 and/or 2 and/or 3, depending on which outputs you need (view

chapter “Connection Diagrams” on page 4).

Note: If more than one plug is used, only one Supply Voltage can be used. The desired menu language

must be selected after initial start-up, and after each reset (see chapter “Display” on page 18

in this regard).

Switch to the configuration menu by pressing any key.

Note: If no settings are adjusted in the configuration menu for a period of 30 seconds, the Sensor is automati-

cally returned to the display mode.

The Sensor accesses the last used menu view when a key is once again activated. If a setting is configured,

it becomes active when the configuration menu is exited.

The keys are used for navigation, and for configuring settings. The functions of the navigation keys vary from

menu to menu. The functions of the keys appear in the display as follows:

5: Navigate up.

6: Navigate down.

3Back: Move up one level within the menu.

7Run: Switch to the display mode.

Selection is acknowledged with the enter key.

Important: Do not use any sharp objects to press the keys when configuring settings, because they

might otherwise be damaged.

5.1. Overview of functions

Description Function Page

Run Switch to display mode 11

Sensors Configuring of the Sensors 11

Outputs Select output function 14

Measure Configuration of the Speed Measurement Function 16

Display Select display characteristics 18

Language Select the desired menu language 19

Info Read out information regarding the Sensor 19

Reset Return to default settings 19

Password Protection against unauthorized changes to settings 20

10 Initial Start-Up

5.2. Menu Structure

• normal

Signal Strength

Switching Status

Indicator/

Connect

* only after Window Teach

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Wenglor

Wenglor

Wenglor OPT2015 Manual de usuario

Wenglor

Wenglor ZD600 Series Manual de usuario

Wenglor

Wenglor OPT2001 Manual de usuario

Wenglor

Wenglor FFAP Series Manual de usuario

Wenglor

Wenglor P1EL Series Manual de usuario

Wenglor

Wenglor UMF402U035 Manual de usuario

Wenglor

Wenglor OPT2010 Manual de usuario

Wenglor

Wenglor P1PA00 Series Manual de usuario

Wenglor

Wenglor OTII802C0103 Manual de usuario

Wenglor

Wenglor UMS603U035 Manual de usuario

Wenglor

Wenglor P1MH Series Manual de usuario

Wenglor

Wenglor P1KH001 Manual de usuario

Wenglor

Wenglor OPT2172-74 Manual de usuario

Wenglor

Wenglor I12N Series Manual de usuario

Wenglor

Wenglor InoxSens series Manual de usuario

Wenglor

Wenglor OPT2170 Manual de usuario

Wenglor

Wenglor YR24PCT2 Manual de usuario

Wenglor

Wenglor P1NH Series Manual de usuario

Wenglor

Wenglor OPT2133 Manual de usuario

Wenglor

Wenglor OPT2130 Manual de usuario

Wenglor

Wenglor P1PY0 Series Manual de usuario

Wenglor

Wenglor P2KH Series Manual de usuario

Wenglor

Wenglor OPT2041 Manual de usuario

Wenglor

Wenglor CP08MHT80 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario