Wenglor OPT2041 Manual de usuario
OPT2041
Fiber Optic Cable Sensor
Operating Instructions
Available as PDF only
Status: 18.06.2018
www.wenglor.com
EN
2
EN
Index
1. Proper Use 3
2. Safety Precautions 3
3. General Information Regarding the Device 3
4. Device Features 4
4.1. Connection Diagrams 4
4.2. Housing Dimensions 4
4.3. Declaration of Conformity 4
4.4. Technical Data 5
4.5. Complementary Products 6
4.6. Control Panel 6
4.7. Installation Instructions 6
4.7.1. Mounting to a DIN rail 6
4.7.2. Side mounting 7
4.7.3. Connecting the plastic fibre-optic cable 7
5. Initial Operation 8
5.1. Overview of Functions 8
5.2. Menu Structure 9
6. Adjustment 10
6.1. Run 10
6.2. Teach-In 10
6.3. Output 12
6.3.1. ON-/OFF-Delay 13
6.4. Operating Mode 13
6.5. Filter 13
6.6. Display 14
6.7. Language 14
6.8. Information 15
6.9. Reset 15
6.10. Password 15
7. IO-Link Parameter and Process data 16
8. Maintenance Instructions 19
9. Proper Disposal 19
3
1. Proper Use
This wenglor product is used in accordance with the following mode of operation:
Both plastic fiber optic cables and glass fiber optic cables can be connected to fiber optic cable sensors.
Universal reflex sensors can be used both with and without fiber optic cables. Fiber optic cable sensors ana-
lyze the light reflected by the object. The output switches when an object reaches the selected range (detec-
tion) or when the active light beam is interrupted (operating limits). Bright objects reflect more light than dark
objects, and can thus be recognized from greater distances. In barrier operation, the color of the object has
no effect on the range.
2. Safety Precautions
• This operating instruction is part of the product and must be kept during its entire service life.
• Read this operating instruction carefully before using the product.
• Installation, start-up and maintenance of this product has only to be carried out by trained personal.
• Tampering with or modifying the product is not permissible.
• Protect the product against contamination during start-up.
• Not a safety component in accordance with the EU Machinery Directive
3. General Information Regarding the Device
wenglor fiber optic cables can be adapted to these Sensors. The modern OLED display assures easy, menu-
driven Sensor setup. Signal strengths and the switching threshold can be read from the display as numeric
values or as a bar graph. Convenient programming and quick diagnosis is possible via the IO-Link interface.
4
EN
4. Device Features
4.1. Connection Diagrams
774
+ Supply Voltage “+”
A/ Switching Output/IO-Link
T Teach Input
– Supply Voltage “0 V”
4.2. Housing Dimensions
1 = Transmitter Diode
2 = Receiver Diode
4.3. Declaration of Conformity
The EC declaration of conformity can be found on our website at www.wenglor.com in download area.
RoHS
5
4.4. Technical Data
Optical Data
Switching Hysteresis < 15 %
Light Source Red Light
Wave Length 660 nm
Service Life (T = +25 °C) 100000 h
Max. Ambient Light 10000 Lux
Electrical Data
Supply Voltage 18...30 V DC 18...30 V DC
Current Consumption (Ub = 24 V) < 40 mA
Switching Frequency 4 kHz
Response Time 125 µs
On-/Off-Delay 0...10000 ms
Temperature Drift < 10 %
Temperature Range –25...60 °C
Switching Output Voltage Drop < 2,5 V
Switching Output / Switching Current 100 mA
Short Circuit Protection yes
Reverse Polarity Protection yes
Overload Protection yes
Teach Mode NT, MT, ZT, DT, FT, HT, TP
Interface IO-Link
IO-Link Version 1.0
IO-Link Parameter > 12
Protection Class III
Mechanical Data
Adjustment Teach-In
Housing Material Plastic
Degree of Protection IP65
Connection M8×1; 4-pin
DIN-Rail mounting 35 mm
General Data
Selectable menu language X
Password Protection X
Output
Configurable as PNP/Push-Pull yes
NO/NC switchable yes
IO-Link yes
6
EN
4.5. Complementary Products
Glass Fiber Optic Cable
Plastic Fiber Optic Cable
4.6. Control Panel
20 = Enter Button
22 = Up Button
23 = Down Button
60 = Display
4.7. Installation Instructions
All applicable electrical and mechanical regulations, standards and safety precautions must be adhered to
when installing and operating the Sensor. The Sensor must be protected against mechanical influences. Install
the device such that its installation position cannot be inadvertently changed.
4.7.1. Mounting to a DIN rail
7
fig.1 Mounting of the Sensor to a DIN rail
4.7.2. Side mounting
Side mounting a unit: Secure the Sensor with screws (M4) through the mounting holes.
fig. 2 Side mounting of the Sensor
4.7.3. Connecting the plastic fibre-optic cable
• Please cut the plastic fibre-optic cable once before using with the cutting tool.
• Open the mounting slide with a screwdriver (see fig. 3-1)
• Insert the light cable into the opening provided to this end (see fig.. 3-2)
• Close the mounting slide (see fig. 3-3)
fig. 3 Connecting the plastic fibre-optic cable
8
EN
5. Initial Operation
Connect the Sensor to 18 to 30 V DC before configuring the settings.
The desired menu language must be selected after initial operation, and after each reset.
See section 6.7 in this regard.
Switch to the configuration menu by pressing any key.
Note: If no settings are adjusted in the configuration menu for a period of 30 seconds, the Sensor is auto-
matically returned to the display mode.
The Sensor accesses the last used menu view when a key is once again activated. If a setting is configured,
it becomes active when the configuration menu is exited.
The keys are used for navigation, and for configuring settings. The functions of the navigation keys vary from
menu to menu. The functions of the keys appear in the display as follows:
5: Navigate up.
6: Navigate down.
3Back: Move up one level within the menu.
7Run: Switch to the display mode.
Selection is acknowledged with the enter key.
Important: Do not use any sharp objects to press the keys when configuring settings,
because they might otherwise be damaged.
5.1. Overview of Functions
Description Function Page
Run Switch to display mode 10
Teach Teach-In the Sensor 10
Output Select output function 12
Operating Mode Select the Sensitivity 13
Filter Filter settings 13
Display Select display characteristics 14
Language Select the desired menu language 14
Info Read out information regarding the Sensor 15
Reset Return to default settings 15
Password Protection against unauthorized changes to settings 15
9
5.2. Menu Structure
The Sensor’s menu is laid out as follows:
• normal
Signal Strength
Password
Switching Status
Indicator/
* Only after Window Teach
10
EN
6. Adjustment
6.1. Run
The Sensor is switched to the display mode when the enter key is pressed.
Received Signal Strength (numeric value 0 – 999)
Switching Status:
Dark dot = Sensor connected
Blinking = Contamination
Bar chart of received
Signal Strength
6.2. Teach-In
The Sensor is set up with the help of the teach-in menu.
Function Description
T Normal Normal Teach-In
The object is taught in by pressing
the T key:
• Align the spot to the object.
• Briefly press the T key.
èThe switching distance to
the object is set.
• If necessary, readjust the
switching distance with the help
of the “Potentiometer” menu item.
T Minimal Minimal Teach-In/Glass recognition
The object is taught in by pressing the T key:
• Align the spot to the object.
• Briefly press the T key.
èThe switching distance to the
object is set.
• If necessary, readjust the
switching distance with the help
of the “Potentiometer” menu item.
T Dynamic Dynamic Teach-In
The Sensor enters a recording phase when the T1 key is pressed, and
the minimum and maximum signal strength are saved to memory.
• Align the spot to the background
(e. g. conveyor belt).
• Briefly press the T1 key.
• Move objects through the light beam.
• Briefly press the T2 key.
èThe switching point is set
automatically between the minimum and maximum signal strength
saved to memory during the recording phase.
Object
Object-
distance (OA)
Calculated
switching
distance is
approximately
50% > OA
Object
Calculated
switching
distance
between
OA 1 and OA 2
Object distance 1
(OA 1)
Object distance 2
(OA 2)
Object
Object-
distance (OA)
Calculated
switching
distance is
approximately
17% > OA
Tabla de contenidos
Otros manuales de Accesorios de Wenglor
Wenglor
Wenglor Y1TA Series Manual de usuario
Wenglor
Wenglor PNBC1 Series Manual de usuario
Wenglor
Wenglor weCat3D MLSL Manual de usuario
Wenglor
Wenglor OPT2168 Manual de usuario
Wenglor
Wenglor CP25QXVT80 Manual de usuario
Wenglor
Wenglor OPT2011 Manual de usuario
Wenglor
Wenglor ODX202 Manual de usuario
Wenglor
Wenglor P1KL Series Manual de usuario
Wenglor
Wenglor OPT1500 Manual de usuario
Wenglor
Wenglor ODX402P0088 Manual de usuario
Wenglor
Wenglor P1PK Series Manual de usuario
Wenglor
Wenglor P1PY0 Series Manual de usuario
Wenglor
Wenglor OPT2001 Manual de usuario
Wenglor
Wenglor UF Series Manual de usuario
Wenglor
Wenglor P2KL Series Manual de usuario
Wenglor
Wenglor P1NE Series Manual de usuario
Wenglor
Wenglor OPT2203 Manual de usuario
Wenglor
Wenglor OCP P0150E Series Manual de usuario
Wenglor
Wenglor UMF402U035 Manual de usuario
Wenglor
Wenglor P1EL Series Manual de usuario
