Wenglor ODX202 Manual de usuario
ODX202
Fiber Optic Cable Sensor
Operating Instructions
Available as PDF only
Status: 10.10.2016
EN
2
EN
Table of Content
1. Proper Use 3
2. Safety Precautions 3
3. Product Features 3
3.1. Connection Diagrams 3
3.2. Housing Dimensions 4
3.3. EC Declaration of Conformity 4
3.4. Technical Data 5
3.5. Contamination Warning 5
3.6. Contamination Output 5
3.7. Complementary Products (see catalog) 6
3.8. Control Panel 6
3.9. Mounting Instructions 6
3.9.1. Mounting to a DIN rail 6
3.9.2. Side mounting 7
3.9.3. Connecting the plastic fibre-optic cable 7
4. Adjustment 8
4.1. On-Delay and Off-Delay 8
4.2. Selecting normally closed or normally open function (NC/NO) 9
4.3. Selecting PNP/NPN/Push-Pull 9
4.4. Setting Switching Distance with the potentiometer 10
4.5. Setting Switching Distance with the Teach-In function 10
4.5.1. Normal Teach-In 10
4.5.2. Minimal Teach-In 11
4.5.3. Dynamic Teach-In (Teach-In with moving objects) 12
4.5.4. Two-point Teach-In 13
4.6. External Teach-In 13
4.7. Selecting the Run function 14
4.7.1. Normal operating mode 14
4.7.2. Selecting the Light pulse frequency 15
4.7.3. Energy saving mode 16
4.8. Test Mode 16
5. Maintenance Instructions 16
6. Proper Disposal 16
3
1. Proper Use
This wenglor product has to be used according to the following functional principle:
Fiber Optic Cable Sensors
Both plastic fiber optic cables and glass fiber optic cables can be connected to fiber optic cable sensors. Uni-
versal reflex sensors can be used both with and without fiber optic cables. Fiber optic cable sensors analyze
the light reflected by the object. The output switches when an object reaches the selected range (detection) or
when the active light beam is interrupted (operating limits). Bright objects reflect more light than dark objects,
and can thus be recognized from greater distances. In barrier operation, the color of the object has no effect
on the range.
2. Safety Precautions
• This operating instruction is part of the product and must be kept during its entire service life.
• Read this operating instruction carefully before using the product.
• Installation, start-up and maintenance of this product has only to be carried out by trained personnel.
• Tampering with or modifying the product is not permissible.
• Protect the product against contamination during start-up.
• Not a safety component in accordance with the EU Machinery Directive.
3. Product Features
3.1. Connection Diagrams
Order number
ODX202P0007 ODX202P0107 ODX202P0008
external Teach Input Contamination Output –
770 771 772
7
7
8
S02
S02
S04
4
EN
770
771
772
+ Supply Voltage “+”
A Switching Output
Contamination Output/Error Output (NC)
– Supply Voltage “0 V”
T Teach Input
3.2. Housing Dimensions
1 = Transmitter Diode
2 = Receiver Diode
3.3. EC Declaration of Conformity
The EC declaration of conformity can be found on our website at www.wenglor.com in download area.
Any additional standards which are applicable for the given application must be observed.
RoHS
5
3.4. Technical Data
Switching Hysteresis < 15 %
Light Source Red Light
Wave Length 660 nm
Service Life (Tu = 25 °C) 100000 h
max. ambient Light 10000 Lux
Supply Voltage 10…30 V DC
Current Consumption (Ub = 24 V) < 40 mA
Switching Frequency 2 kHz
Response Time 250 µs
ON-/OFF-Delay 0…200 ms
Temperature Drift < 10 %
Temperature Range –25…60 °C
Switching Output Voltage Drop < 2,5 V
Switching Output/Switching Current 200 mA
Short Circuit Protection yes
Reverse Polarity Protection yes
Overload Protection yes
Teach Mode NT, MT, ZT, DT, TP
Adjustment Teach-In
Housing Plastic
Full Encapsulation yes
Degree of Protection IP65
Connection M8×1
Protection Class III
DIN-Rail mounting 35 mm
3.5. Contamination Warning
The contamination warning (included with all ODX202 types) is indicated by means of a blinking red LED (02)
(with rotary switch in the Run position).
3.6. Contamination Output
The contamination output (included with ODX202P0107) functions as a normally closed contact and is
switched off if the Sensor is operated within an unreliable range.
Unreliable range: ontamination, misalignment
6
EN
3.7. Complementary Products (see catalog)
wenglor offers Connection Technology for field wiring.
Suiting Connection Technology No.
7
S02
8
S04
Glass Fiber Optic Cable
Plastic Fiber Optic Cable
3.8. Control Panel
07 24 01 02 25
01 = Switching Status Indicator
02 = Contamination Warning
07 = Selector Switch
24 = Plus Button
25 = Minus Button
3.9. Mounting Instructions
All applicable electrical and mechanical regulations, standards and safety precautions must be adhered to
when installing and operating the Sensor. The Sensor must be protected against mechanical influences. Install
the product such that its installation position cannot be inadvertently changed.
3.9.1. Mounting to a DIN rail
7
fig.1 Mounting of the Sensor to a DIN rail
3.9.2. Side mounting
Side mounting a unit: Secure the Sensor with screws (M4) through the mounting holes.
fig. 2 Side mounting of the Sensor
3.9.3. Connecting the plastic fibre-optic cable
• Please cut the plastic fibre-optic cable once before using with the SW cutting tool.
• Open the mounting slide with a screwdriver (see fig. 3-1)
• Insert the light cable into the opening provided to this end (see fig. 3-2)
• Close the mounting slide (see fig. 3-3)
fig. 3 Connecting the plastic fibre-optic cable
8
EN
4. Adjustment
4.1. On-Delay and Off-Delay
fig. 4 On-Delay and Off-Delay
Adjusting On- and Off-Delay
with rotary selector switch (07) set to On-Delay or Off-Delay
Delay Minus Button (25) Plus Button (24) Gelbe Status-LED (02)
0 ms lighted up not lighted up not lighted up
10 ms not lighted up not lighted up 1 × blinks, pause, 1 × blinks
20 ms not lighted up not lighted up 2 × blinks, pause, 2 × blinks
• • • • • •
• • • • • •
200 ms not lighted up lighted up 20 × blinks, pause, 20 × blinks
Adjusting On-Delay Adjusting Off-Delay
• Set rotary selector switch (07) to On-Delay • Set rotary selector switch (07) to Off-Delay
• Activate the plus button (24) • Activate the plus button (24)
èDelay is increased by 10 ms èDelay is increased by 10 ms
• Activate the minus button (25) • Activate the minus button (25)
èDelay is reduced by 10 ms èDelay is reduced by 10 ms
• Set rotary selector switch (07) to Run • Set rotary selector switch (07) to Run
9
4.2. Selecting normally closed or normally open function (NC/NO)
•Set rotary selector switch (07) to NC/NO
PNP/NPN
• Activate the plus button (24)
èNC is selected (normally closed/dark switching)
èPlus button (24) lights up
• Activate the minus button (25)
èNO is selected (normally open/light switching)
èMinus button (25) lights up
• Set rotary selector switch (07) to Run
4.3. Selecting PNP/NPN/Push-Pull
• Set rotary selector switch (07) to NC/NO
PNP/NPN
• Activate the plus button (24) for 5 seconds
èPlus button (24) and Minus button (25) blink
• Release Plus button (24)
• Activate the plus button (24)
èPlus Button (24) lights up
èPNP setting
• Activate the minus button (25)
èMinus button (25) lights up
èNPN setting
• Activate Plus button (24) and minus button (25) at the same time
èPlus button (24) and minus button (25) light up
èPush-pull setting
• Set rotary selector switch (07) to Run
10
EN
4.4. Setting Switching Distance with the potentiometer
• Set rotary selector switch (07) to Poti
• Activate the plus button (24)
èSwitching Distance is increased
• Activate the minus button (25)
èSwitching Distance is reduced
The LEDs at the plus and minus buttons function like a light scale. The more brightly the respective button is
illuminated, the greater the sensing distance and vice versa.
The corresponding button blinks if maximum or minimum sensing distance has been selected.
• Set rotary selector switch (07) to Run
4.5. Setting Switching Distance with the Teach-In function
The ideal Switching Distance for the object to be recognized is selected automatically with the Teach-In function:
Normal Teach-In
Minimal Teach-In
Dynamic Teach-In
Two-point Teach-In
4.5.1. Normal Teach-In
• Set rotary selector switch (70) to Teach
èRed LED (02) lights up
• Align spot to object
• Activate the plus button (24)
èPlus button (24) lights up
• Activate the plus button (24) again*
èPlus button (24) is no longer illuminated
• Set rotary selector switch (07) to Run
*If a second button operation does not take place within 40 seconds, the teach-in process is aborted without saving any settings.
Tabla de contenidos
Otros manuales de Accesorios de Wenglor
Wenglor
Wenglor P1PK Series Manual de usuario
Wenglor
Wenglor OPT2168 Manual de usuario
Wenglor
Wenglor U1RT002 Manual de usuario
Wenglor
Wenglor P2KH002 Manual de usuario
Wenglor
Wenglor P1PA00 Series Manual de usuario
Wenglor
Wenglor P1NE Series Manual de usuario
Wenglor
Wenglor TIF352U0089 Manual de usuario
Wenglor
Wenglor OPT2145 Manual de usuario
Wenglor
Wenglor OPT2011 Manual de usuario
Wenglor
Wenglor P1KK Series Manual de usuario
Wenglor
Wenglor P2KH Series Manual de usuario
Wenglor
Wenglor P1KY0 Series Manual de usuario
Wenglor
Wenglor P1PK104 Manual de usuario
Wenglor
Wenglor OPT2041 Manual de usuario
Wenglor
Wenglor PNBC Series Manual de usuario
Wenglor
Wenglor P1KT Series Manual de usuario
Wenglor
Wenglor Y1TA Series Manual de usuario
Wenglor
Wenglor ShapeDrive G4 MLAS 1 Series Manual de usuario
Wenglor
Wenglor OY2TA104P0150E Manual de usuario
Wenglor
Wenglor P2KK Series Manual de usuario
