Weider 831.159010 Manual de usuario

USER'S MANUAL

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Model No. 831.159010

Serial No.

Write the serial number in the

space above for reference.

Serial Number Decal (under seat)

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

SEARS, ROEBUCK AND CO.

HOFFMAN ESTATES, IL 60179

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before

beginning assembly.

TABLE OF CONTENTS

1. Read all instructions in this manual and in

the accompanying literature before using the

weight system. Use the weight system only

as described in this manual.

2. It is the responsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all precautions.

3. The weight system is intended for home use

only. Do not use the weight system in a com-

mercial, rental, or institutional setting.

4. Use the weight system only on a level sur-

face. Cover the floor or carpet beneath the

weight system to protect the floor.

5. Make sure all parts are properly tightened

each time the weight system is used.

Replace any worn parts immediately.

6. Keep children under the age of 12 and pets

away from the weight system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion when using the weight system.

9. The weight system is designed to support a

maximum user weight of 300 pounds. Do not

place more than 150 pounds on the weight

carriage. Note: The weight system does not

include weights.

10. Never release the press arm, butterfly arms,

leg lever, lat bar, or handle while weights are

raised; the weights will fall with great force.

11. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you

are exercising, stop immediately and make

sure that the cables are on all of the pulleys.

12. Always stand on the foot plate when per-

forming an exercise that could cause the

weight system to tip.

13. Always disconnect the lat bar from the

weight system when performing an exercise

that does not use the lat bar.

14. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

15. The warning decals

shown here have been

placed on the weight

system in the locations

shown on page 4. If a

decal is missing or

illegible, please call

our toll-free HELPLINE

at 1-800-736-6879,

Monday through

Saturday, 7 a.m. until

7 p.m. Central Time, to

order a free replace-

ment decal. Place the

decal on the weight

system in the loca-

tion shown.

WARNING: To reduce the risk of serious injury, read the following important precau-

tions before using the weight system.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. SEARS assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

Keep hands and

fingers clear of

this area.

IMPORTANT PRECAUTIONS

Decal 1

Decal 2

BEFORE YOU BEGIN

ASSEMBLED

DIMENSIONS:

Height: 74 in.

Width: 42 in.

Length: 60 in.

Foot Plate

Low Pulley Station

High Pulley Station

Front Upright

Lat Bar

Leg Lever

Press Arm/Butterfly Arm

Warning Decal 2

(One on each side

of the front upright.)

Weight Carriage

Seat

Backrest

Thank you for selecting the versatile WEIDER®2100

weight system. The WEIDER®2100 offers a selection

of weight stations designed to develop every major

muscle group of the body. Whether your goal is to tone

your body, build dramatic muscle size and strength, or

improve your cardiovascular system, the WEIDER®

2100 will help you to achieve the results you want.

For your benefit, read this manual carefully before

using the weight system. If you have additional

questions, please call our toll-free HELPLINE at

1-800-736-6879, Monday through Saturday, 7 a.m.

until 7 p.m. Central Time (excluding holidays). To help

us assist you, please note the product model number

and serial number before calling. The model number is

831.159010. The serial number can be found on a

decal attached to the weight system (see the front

cover of this manual).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

Warning Decal 1

Before beginning assembly, carefully read the

following information and instructions:

•Assembly requires two people.

•Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until assembly is completed.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

•As you assemble the weight system, make sure

all parts are oriented as shown in the drawings.

•For help identifying small parts, use the PART

IDENTIFICATION CHART.

The following tools (not included) are required

for assembly:

• two adjustable wrenches

• one rubber mallet

• one standard screwdriver

• one Phillips screwdriver

• lubricant, such as grease or petroleum jelly,

and soapy water.

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Make Things Easier for Yourself

Everything in this manual is designed to ensure

that the weight system can be assembled suc-

cessfully by anyone. However, it is important to

realize that the versatile weight system has

many parts and that the assembly process will

take time. Most people find that by setting aside

plenty of time, assembly will go smoothly.

ASSEMBLY

77 75

Indents

1. Before beginning assembly, be sure that you

have read and understand the information in

the box above.

Press two 50mm x 75mm Inner Caps (29) into

the sides of the Foot Plate (74).

Orient the Rear Base (3) with the indents around

the holes on the bottom. Attach the Front Base

(1) and the Rear Base to the Center Base (2) with

two M10 x 70mm Bolts (58) and two M10 Nylon

Locknuts (71).

FRAME ASSEMBLY

2. Insert six M10 x 65mm Carriage Bolts (57) up

through the Front and Rear Bases (1, 3).

Press the three Base Caps (28) onto the ends of

the Front Base (1), the Center Base (2), and the

Rear Base. Secure the Base Caps with three M4

x 20mm Screws (77) and three M5 Washers (75).

Attach the Foot Plate (74) to the Center Base (2)

with two M10 x 65mm Carriage Bolts (57) and

two M10 Nylon Locknuts (71).

4. Press a 50mm Square Inner Cap (22) into the

Seat Upright (73). Attach the Bumper (25) to the

Seat Upright with an M4 x 20mm Screw (77) and

an M5 Washer (75).

Attach the Seat Upright (73) to the Front Base (1)

with the two indicated M10 x 65mm Carriage

Bolts (57) and two M10 Nylon Locknuts (71). Do

not tighten the Nylon Locknuts yet.

3. Attach the Rear Upright (7) to the Rear Base (3)

with the two indicated M10 x 65mm Carriage

Bolts (57) and two M10 Nylon Locknuts (71).

Press a 38mm Square Inner Cap (41) into the

tube on the Front Upright (6).

Attach the Front Upright (6) to the Front Base (1)

with the two indicated M10 x 65mm Carriage

Bolts (57) and two M10 Nylon Locknuts (71).

Do not tighten the M10 Nylon Locknuts (71)

yet.

Hole

5. Make sure there is a Carriage Bushing (32) inside

the top of the Carriage Stop (31). Slide the

Carriage Stop onto the Rear Upright (7) and

attach it at the indicated hole (see the inset draw-

ing) with an M8 x 70mm Bolt (72) and an M8

Nylon Locknut (70).

Make sure there are two Carriage Bushing (32)

inside the top and bottom of the Weight Carriage

(14). Press two 25mm Round Inner Caps (33)

into the ends of the tube on the Weight Carriage.

Insert an M10 x 20mm Bolt (67) into the bracket

on the Weight Carriage.

Slide the Weight Carriage (14) onto the Rear

Upright (7). Press a 50mm Square Inner Cap (22)

onto the top of the Rear Upright.

6. Press a 50mm Square Inner Cap (22) into the

end of the Top Frame (8).

Attach the Top Frame (8) to the Front Upright (6)

with two M10 x 70mm Bolts (58), the 90mm

Space Support Plate (21), and two M10 Nylon

Locknuts (71).

Attach the Top Frame (8) to the Rear Upright (7)

with two M10 x 70mm Bolts (58), the 70mm

Space Support Plate (56), and an M10 Nylon

Locknut (71).

Do not tighten the M10 Nylon Locknuts (71)

yet.

8. Press a 50mm Square Inner Cap (22) into the

Butterfly Frame (9).

Lubricate the M10 x 75mm Bolt (60) with grease.

Attach the Butterfly Frame (9) to the Top Frame

(8) with the Bolt and an M10 Nylon Locknut (71).

Do not overtighten the Locknut; the Butterfly

Frame must be able to pivot easily.

71 71

Lubricate

7. Attach the Seat Frame (5) to the Front Upright (6)

with two M10 x 70mm Bolts (58), two M10

Washers (26), and two M10 Nylon Locknuts (71).

Attach the Seat Frame (5) to the Seat Upright

(73) with two M10 x 70mm Bolts (58), two M10

Washers (26), and two M10 Nylon Locknuts (71).

Tighten the M10 Nylon Locknuts (71) used in

steps 2–7. 26

ARM ASSEMBLY

11. Press two 40mm x 50mm Inner Caps (23) into

the ends of the Leg Lever (4).

Lubricate an M10 x 65mm Bolt (59) with grease.

Attach the Leg Lever (4) to the Seat Upright (73)

with the Bolt and an M10 Nylon Locknut (71). Do

not overtighten the Locknut; the Leg Lever

must be able to pivot easily.

10. Lubricate an M10 x 82mm Bolt (50) and both

sides of two Plastic Washers (55) with grease.

Attach the Right Butterfly Arm (11) to the Butterfly

Frame (9) with the Bolt, the two Plastic Washers,

two Butterfly Caps (54), and an M10 Nylon

Locknut (71). Do not overtighten the Locknut;

the Butterfly Arm must be able to pivot easily.

Be sure the indented sides of the Plastic

Washers fit over the welded bushing in the

Butterfly Arm.

Repeat this step with the Left Butterfly Arm

(10).

9. Press a 40mm x 50mm Inner Cap (23) into the

indicated end of the Right Butterfly Arm (11). Wet

the bottom end of the Arm with soapy water. Slide

a Large Foam Pad (19) onto the Arm.

Attach a Pivot Bracket (48) to the Right Butterfly

Arm (11) with an M10 x 50mm Bolt (62) and an

M10 Nylon Locknut (71). Do not overtighten the

Locknut; the Pivot Bracket must be able to

pivot easily.

Slide a Foam Grip (76) onto the Right Handle

(13). Attach the Handle to the Right Butterfly Arm

(11) with two M8 x 15mm Bolts (64).

Slide the Large Foam Pad (19) down so that the

bottom of the Foam Pad is even with the bottom of

the Arm.

Repeat this step with the Left Butterfly Arm (10).

Lubricate

Welded

Bushing

Lubricate

4Lubricate

23 73

15. Wrap the Butterfly Cable (46) around a “V”-Pulley

(39). Attach the Pulley and a Long Cable Trap

(40) to the bracket on the Front Upright (6) with

an M10 x 55mm Bolt (69) and an M10 Nylon

Locknut (71). Be sure the Cable Trap is turned

to hold the Cable in the Groove of the Pulley.

12. Locate the Butterfly Cable (46). Attach the

Butterfly Cable to the indicated Pivot Bracket (48)

with an M8 x 27mm Shoulder Bolt (63) and an M8

Nylon Locknut (70).

13. Wrap the Butterfly Cable (46) around a “V”-Pulley

(39). Attach the Pulley and a Long Cable Trap

(40) to the bracket on the Front Upright (6) with

an M10 x 55mm Bolt (69) and an M10 Nylon

Locknut (71). Be sure the Cable Trap is turned

to hold the Cable in the Groove of the Pulley.

14. Wrap the Butterfly Cable (46) around a 90mm

Pulley (38). Attach the Pulley to the Double “U”-

Bracket (37) with an M10 x 47mm Bolt (61) and

an M10 Nylon Locknut (71).

CABLE ASSEMBLY

18. Wrap the High Cable (45) around a 90mm Pulley

(38). Attach the Pulley inside the Top Frame (8)

with an M10 x 70mm Bolt (58), two M10 Washers

(26), two 13mm Spacers (34), and an M10 Nylon

Locknut (71).

19. Wrap the High Cable (45) around a 90mm Pulley

(38). Attach the Pulley and a Cable Trap (44) to

the second set of holes from the top of the two

Pulley Plates (36) with an M10 x 47mm Bolt (61)

and an M10 Nylon Locknut (71). Be sure the

Cable Trap is turned to hold the Cable in the

Groove of the Pulley.

17. Locate the High Cable (45). Route the eyelet

end of the Cable up through the Top Frame (8)

and around a 90mm Pulley (38). Attach the Pulley

inside the Top Frame with an M10 x 70mm Bolt

(58), two M10 Washers (26), two 13mm Spacers

(34), and an M10 Nylon Locknut (71).

16. Attach the Butterfly Cable (46) to the indicated

Pivot Bracket (48) with an M8 x 27mm Shoulder

Bolt (63) and an M8 Nylon Locknut (70).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Gimnasio en casa de Weider

Weider

Weider Tc 150 Bench Manual de usuario

Weider

Weider WEMC0942.1 Manual de usuario

Weider

Weider Pro 125 Bench Manual de usuario

Weider

Weider WEEVBE33110 Manual de usuario

Weider

Weider WESY81080 Manual de usuario

Weider

Weider TDPWM0 Manual de usuario

Weider

Weider 240 Tc Bench Manual del sistema

Weider

Weider Cswb2 Bench Manual de usuario

Weider

Weider Pro 400L Manual de usuario

Weider

Weider PRO 575 Manual de usuario

Weider

Weider 831.159380 Manual de usuario

Weider

Weider E540 Power Master Manual de usuario

Weider

Weider C101predator Manual de usuario

Weider

Weider 4990 I Manual de usuario

Weider

Weider WESY2916.1 Manual de usuario

Weider

Weider Platinum Plus 1000 Manual de usuario

Weider

Weider Victory Manual de usuario

Weider

Weider Power Flex D621 354.156350 Manual de usuario

Weider

Weider WEBE96490 Manual de usuario

Weider

Weider Power D610 Manual de usuario

Weider

Weider B460 Bench Manual de usuario

Weider

Weider PRO 408 Manual de usuario

Weider

Weider 340 L Manual de usuario

Weider

Weider Easy Compact 90 Manual de operación y mantenimiento

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario

Insportline

Insportline RW600 Manual de usuario

Stamina

Stamina 55-1532 Manual de usuario

Tunturi

Tunturi R25 Manual de usuario