Weber mt SRV 660 Instrucciones de funcionamiento
1 SRV 660
SRV 660
Honda GXR 120
1117/englisch/Übersetzung der Original-Betriebsanleitung
Operating and
Maintenance Manual
Weber Maschinentechnik GmbH
Im Boden 5– 8, 10
D-57334 Bad Laasphe-Rückershausen/Germany
Tel.: +49 (0) 27 54 / 398 0
Fax: +49 (0) 27 54 / 398 101
E-mail: [email protected]
Web: www.webermt.de
2 SRV 660
3 SRV 660
Table of contents
Introduction 4
Safety guidelines 5
Graphic presentation 8
Device description 9
Technical data 10
Activities prior to starting work 12
Starting 13
Tamping 14
Shutting down 14
Maintenance overview 15
Maintenance work 16
Operating uids and ll levels 19
Troubleshooting 19
Storage 20
Contact addresses 23
4 SRV 660
Introduction
This operating and maintenance manual is designed to facilitate familiarization with your tamper, and
enable you to maintain the tamper and use it in accordance with the proper application possibilities.
When complying with the instructions in the operating and maintenance manual you help avoid
hazards, reduce repair and downtime costs, and increase the reliability and service life of your tamper.
This operating and maintenance manual must always be available at the implementation site of the
tamper.
If necessary, you can obtain additional information from your authorized WEBER dealer, or you can
obtain information from one of the contact addresses on the last page.
You can obtain information on the assembled Honda gasoline engine and nd a spare-part list for it at
www.honda-engines-eu.com.
The valid conformity declaration is enclosed with every machine delivery.
5 SRV 660
Safety guidelines
General
All safety instructions must be read and complied with, non-compliance results in
– Danger to life and limb of the user
– Impairments to the machine or other property.
In addition to the operating manual, the accident-prevention regulations in the country where the
appliance is used must be complied with.
Intended use
The tamper should only be used in technically faultless condition, as intended, in a safety-conscious and
hazard-conscious manner, in compliance with the instructions in the operating manual. Malfunctions that
impair safety must be eliminated without delay.
The SRV 660 tamper is designed exclusively for compacting
– sand
– gravel
– crushed rock
– semi-cohesive mixed material.
Any other use of the tamper is considered to be improper use for which the owner shall be exclusively
responsible. All liability is rejected if damage occurs due to non-compliance with this provision.
This risk is borne solely by the user.
Easily foreseeable misuse
Any use for which the machine is not intended.
Operation
Tampers should only be operated by suitable personnel of at least 18 years of age. Operators must
be instructed in how to guide the tamper by the owner or by owner’s assigned personnel.
The machine operator must comply with trafc regulations. If instructions that affect safety are given
by third persons, then the operator must be authorized to reject these instructions.
Unauthorized persons are forbidden from being in the area of the tamper during the compacting
process.
Protective equipment
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also
face additional dangers when using the machine. Precautionary action must, therefore, be taken.
Protective equipment includes:
Hearing protection
Hard hat
Safety shoes
Protective gloves
6 SRV 660
Maintenance and repair work
Only use original Weber spare parts to ensure reliable and safe operation for maintenance or
repair work.
Adjusting tasks, maintenance tasks, and inspection tasks must be executed on schedule as specied
in this operating and maintenance manual. These activities should only be executed by instructed
personnel.
For repair, maintenance, or inspection work the engine of the tamper must be safeguarded against
unintentional starting.
All pressurized lines, particularly hydraulic lines and lines of the injection system of the drive motor
must be depressurized before performing maintenance or repair tasks.
For maintenance and repair tasks the tamper must be placed on a level and stable substrate and
must be secured from rolling off or tipping over.
Heavy components and subassemblies must be secured on hoisting machines with adequate bearing
capacity when they are replaced. Ensure that no hazard exists related to the raised components or
subassemblies.
Do not position yourself or work under suspended loads.
Operation under difcult conditions
Never inhale the exhaust gas; it contains carbon monoxide, a colorless and odorless gas that is
extremely hazardous, which if inhaled even briey can cause unconsciousness and death.
Never operate the engine in enclosed areas or in areas that are poorly ventilated (tunnels, caves,
etc.) Exercise particular caution when operating the engine in the vicinity of people and livestock.
Operation
Prior to starting work the owner of the tamper must be familiar with the work environment. The work
environment includes obstacles in the work and trafc area, the bearing capacity of the ground,
as well as the necessary safeguarding of the construction site in the area adjacent to public trafc;
and it includes compliance with trafc regulations.
The tamper should only be operated when the protective xtures are mounted. The protective xtures
must all be in functional condition.
At least once per shift the tamper must be checked for apparent defects. If there are apparent defects
then operation of the tamper must be stopped immediately and the responsible person must be
informed. Prior to restarting, tamper malfunctions that have occurred must be corrected.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact
with the skin, clean affected skin with suitable cleaning agent without delay.
7 SRV 660
Inspection
Tampers must be inspected in accordance with appropriate implementation conditions and operating
conditions, as needed; however an inspection to ensure operationally safe status must be performed
by an expert at least once a year. The results of the inspection must be recorded in writing and must
be stored at least until the next inspection.
Cleaning work
Prior to cleaning the tamper with a high-pressure cleaner, protect all accessible energized switches,
cable connections, etc. against water penetration by masking them off.
Cleaning tasks should only be executed in areas that are suitable and have been approved for this
purpose (oil separator amongst others).
Disposal
All operating uids and auxiliary materials must be disposed of in an environmentally-compatible
manner in accordance with country-specic regulations.
Important information for operating and maintenance personnel is marked by pictograms.
Warning against irritants or materials hazardous to health
Warning against a hazardous place
Warning against a suspended load
Wear ear protection
General regulation
Environmental protection
Hard hat
Safety shoes
Protective gloves
8 SRV 660
1
2
3
4
5
6
7
8
10
9
11
Graphic presentation
1 Fuel tank 6 Tamping system
2 Gas lever 7 Tamping foot
3 Manual guidance rod 8 Main lter
4 Engine 9 Secondary air lter
5 Transport roller 10 Handle
11 Hearing protection (sticker)
Total overview SRV 660
9 SRV 660
Device description
The series SRV 660 tamper is used for road-building, canal construction, pipe laying and landscaping
compaction tasks.
Drive
The tamper is powered by an air-cooled Honda gasoline engine.
Force is transmitted via the centrifugal clutch directly to the tamping system. The compaction work
is performed by the tamping foot.
The engine is protected by a double lter system consisting of an oversized main air lter and an
additional air lter.
Operation
Start the Honda gasoline engine with the attached reversing starter.
After starting, the stamping system starts to vibrate via the centrifugal clutch which is attached to
the engine. Use the gas lever to vary the engine speed between idle speed and full-throttle speed.
For easier transport the tamper can be pushed onto or into a means of transport with the help of the
transport roller.
10 SRV 660
Technical data
SRV 660 HD
Weight
Operating weight CECE (in kg) 70
Dimensions
Overall length (in mm) 740
Overall width (in mm) 365
Height (in mm) 1035
Tamping foot width (in mm) 280
Impact rate (/min) 700
Stroke (in mm) 69.4
Drive
Engine manufacturer Honda
Type GXR 120
Performance at operating speed in accordance
with ISO 3046-1 (kW)
2.6
Combustion process 4-stroke gasoline
Operating speed (m/min) 4100
Fuel Unleaded
gasoline
SRV 660 HD
Noise emissions in accordance with 2000/14/EC
Sound pressure level LPA
ascertained in accordance with EN 500, in dB (A) 98
Sound power level L WA ascertained in accordance
with EN ISO 3744 and EN 500, in dB (A) 108
Vibration values
Root-mean-square
acceleration value for hand-arm vibration
ascertained in accordance with EN 500 in m/s² 8.0
In accordance with directive 2006/42/EC,
complying with the vibration values is the
owner’s responsibility.
Otros manuales para SRV 660
1
Tabla de contenidos
Otros manuales de Apisonadora y apisonadora vibratoria de Weber mt
Weber mt
Weber mt CR 1-II Hd Instrucciones de funcionamiento
Weber mt
Weber mt CR 5 E Instrucciones de funcionamiento
Weber mt
Weber mt SRE 300 Instrucciones de funcionamiento
Weber mt
Weber mt CR 9-II MDM Instrucciones de funcionamiento
Weber mt
Weber mt SRV 590-II Instrucciones de funcionamiento
Weber mt
Weber mt SRV 660 Instrucciones de funcionamiento
Weber mt
Weber mt SRV 300 Instrucciones de funcionamiento
Weber mt
Weber mt SRE 590 DC Instrucciones de funcionamiento
Weber mt
Weber mt SRV 620-II Instrucciones de funcionamiento
Weber mt
Weber mt CR 3-II E Instrucciones de funcionamiento
Weber mt
Weber mt CR 3-II Instrucciones de funcionamiento
Weber mt
Weber mt CF 1 R Instrucciones de funcionamiento
Weber mt
Weber mt SRV 660-II Instrucciones de funcionamiento
Weber mt
Weber mt SRV 600 i Instrucciones de funcionamiento
Weber mt
Weber mt CR 2 R Instrucciones de funcionamiento
Weber mt
Weber mt CF 1 HD Instrucciones de funcionamiento
Weber mt
Weber mt CR 9-II CCD 2.0 Instrucciones de funcionamiento
Weber mt
Weber mt CR 3-II Hd Instrucciones de funcionamiento
Weber mt
Weber mt SRV 300-II Instrucciones de funcionamiento
Weber mt
Weber mt CR 5 Guía de configuración
