Webasto Telestart T91 Manual de usuario

09/2009

Einbauanweisung

Installation instructions

Notice de montage

Istruzioni di montaggio

Instrucciones de montaje

Montagehandleiding

Monteringsvejledning

Monteringsanvisning

Monteringshåndbok

Asennusohje

Instrukcja montażu

Návod k instalaci

Beépítési utasítás

Инструкция по монтажу

Telestart T91 / T100 HTM

Improper installation or repair of Webasto heating and cooling systems can cause fire or the leakage of

deadly carbon monoxide leading to serious injury or death.

To install and repair Webasto heating and cooling systems you need to have completed a Webasto

training course and have the appropriate technical documentation, special tools and special equipment.

NEVER try to install or repair Webasto heating or cooling systems if you have not completed a Webasto

training course, you do not have the necessary technical skills and you do not have the technical

documentation, tools and equipment available to ensure that you can complete the installation and

repair work properly.

ALWAYS carefully follow Webasto installation and repair instructions and heed all WARNINGS.

Webasto rejects any liability for problems and damage caused by the system being installed by

untrained personnel.

Telestart T91 / T100 HTM

Inhalt

Einbauanweisung .......................................................1

Allgemein .................................................................1

Zertifizierung ............................................................1

Schalteingang für analoge Anbindung der

Bedienelemente .....................................................2

Vorwahluhr .........................................................2

Taster ..................................................................2

Umstellung Schalteingang von „Vorwahluhr“

auf „Taster“ ...................................................2

Umstellung Schalteingang von „Taster“

auf „Vorwahluhr“ ..........................................2

Lieferumfänge .............................................................3

Lieferumfang T91 ................................................3

Lieferumfang T100 HTM ......................................3

D-Netz Telefonkit (Option) ...................................3

Einbau ..........................................................................4

Einbau Telestart-Empfänger .................................4

Einbau Antenne ...................................................4

Einbau D-Netz Telefonkit (Option) ........................5

Einbau ESVT-Adapter

(am Beispiel Thermo Top C) ............................5

Telestart T91 / T100 HTM Nachrüstung .....................6

In Verbindung mit bestehender oder neu

zu verbauender Vorwahluhr .................................6

In Verbindung mit Taster ..........................................7

Telestart T80 mit Vorwahluhr vorhanden ..................7

Option Lüften bei analoger Anbindung .....................8

Sommer-/Winterschalter vorhanden

(Option Lüften aktivieren) ...............................8

Sommer-/Winterschalter vorhanden

(Option Lüften deaktivieren) ...........................8

Sommer-/Winterschalter neu installieren

(Option Lüften aktivieren) ...............................8

Einbau Temperatursensor

(nur bei T100 HTM) .............................................9

Grundeinstellungen der Komfortstufe .......................9

Technische Daten ......................................................10

Anlagen ....................................................................11

Content

Installation Instructions ........................................... 15

General information ............................................... 15

Certification ........................................................... 15

Switching input for analogue connection of heater

controls ................................................................. 16

Digital timer ...................................................... 16

Pushbutton switch ............................................. 16

Changeover of switching input from

"digital timer" to "pushbutton switch" ........ 16

Changeover of switching input from

"pushbutton switch" to "digital timer" ........ 16

Scope of delivery ...................................................... 17

Scope of delivery for T91 ...................................17

Scope of delivery for T100 HTM ........................17

D network telephone kit (option) ....................... 17

Installation ................................................................ 18

Installation of Telestart receiver ......................... 18

Installation of aerial ........................................... 18

Installation of D network telephone kit (option) . 19

Installation of ESVT adapter

(using example of Thermo Top C) .................19

Telestart T91/T100 HTM retrofit .............................. 20

In conjunction with existing or new digital timer

to be installed ................................................... 20

In conjunction with pushbutton .............................. 21

Telestart T80 with digital timer installed .................. 21

Ventilation option with analogue connection .......... 22

Summer/winter switch installed

(activate ventilation option) .......................... 22

Summer/winter switch installed

(deactivate ventilation option) ...................... 22

Install new summer/winter switch

(activate ventilation option) .......................... 22

Temperature sensor installation

(only with T100 HTM) ........................................ 23

Default settings of comfort level ............................. 23

Technical data .......................................................... 24

Appendices ............................................................... 25

Index

Notice de montage ................................................... 29

Informations générales ........................................... 29

Certification ........................................................... 29

Entrée de couplage pour la connexion analogique

des éléments de commande ............................... 30

Horloge de programmation ............................... 30

Bouton-poussoir ................................................ 30

Passage de l'entrée de couplage de « horloge de

programmation » à « bouton-poussoir » ...... 30

Passage de l'entrée de couplage de « bouton-pous-

soir » à «horloge de programmation ............ 30

Compositions de la fourniture ................................ 31

Composition de la fourniture T91 ...................... 31

Composition de la fourniture T100 HTM ........... 31

Kit téléphone réseau D (en option) .................... 31

Montage .................................................................... 32

Montage du récepteur Telestart ........................ 32

Montage de l'antenne ....................................... 32

Montage du kit téléphone réseau D (en option) 33

Montage de l'adaptateur ESVT

(à l'exemple du Thermo Top C) .................... 33

Telestart T91/T100 HTM de deuxième monte ........ 34

En combinaison avec une horloge de programmation

déjà existante ou devant encore être montée .... 34

En combinaison avec le bouton-poussoir ................ 35

Telestart T80 avec horloge de programmation

déjà existant ...................................................... 35

Option ventilation en cas de connexion analogique 36

Interrupteur été/hiver déjà existant

(activation de l'option ventilation) ................ 36

Interrupteur été/hiver déjà existant

(désactivation de l'option ventilation) ........... 36

Interrupteur été/hiver devant encore être installé

(activation de l'option ventilation) ................ 36

Montage du capteur de température

(uniquement sur le T100 HTM) .......................... 37

Réglages de base du niveau de confort .................. 37

Caractéristiques techniques .................................... 38

Annexes ................................................................... 39

Telestart T91 / T100 HTM

Installation Instructions

General information

The Webasto heaters of the Thermo Top

series can be retrofitted with the Webasto

Telestart T91 and T100 HTM.

The D network telephone kit (option)

enables the Telestart receiver to be

connected to any existing D network aerial.

Certification

The CE mark is visible when the battery com-

partment cover is open.

The e1 mark is located on the Telestart re-

ceiver.

Telestart T91 / T100 HTM

Switching input for analogue connection of heater controls

In addition to the Telestart, a digital timer or

a pushbutton switch can be installed.

Caution:

The digital timer and the pushbutton switch

transmit differing signals to the Telestart re-

ceiver!

The signal input must be adapted to the ap-

propriate heater control!

By default, the signal input of the Telestart

receiver is tuned to the digital timer!

The included ESVT adapter must be adapted

to the existing installation situation (heater

controls and heaters) accordingly by "pin-

ning it in".

See Kapitel "Appendices".

Digital timer

When the heater is activated (by pressing the

instant heat button or by the start of a preset

heater operating time) the Telestart receives

a continuous plus signal from the digital tim-

er during the entire operating time.

Upon deactivation of the heater (by pressing

the instant heat button or when the end of

the operating time preset on the digital timer

is reached), the positive signal is cut off and

the heater is switched off.

Pushbutton switch

Upon switching on or off using the pushbut-

ton switch, the Telestart receiver receives a

short plus signal.

For the Telestart to be able to recognise this

signal, the switching input needs to be set to

"pushbutton switch".

The heater does not switch on if the switch-

ing input is not changed over to "pushbut-

ton switch". Instead, it enters the post-

operation stage and then switches off.

Changeover of switching input

from "digital timer" to "push-

button switch"

- Remove fuse 1A (black) from the heat-

er's fuse holder (voltage interruption).

- Wait at least 5 seconds

- Install fuse in heater's fuse holder and

briefly actuate the pushbutton switch

1x within 5 seconds

- Changeover is terminated

Changeover of switching input

from "pushbutton switch" to

"digital timer"

- Remove fuse 1A (black) from the heat-

er's fuse holder (voltage interruption).

- Wait at least 5 seconds

- Install fuse in heater's fuse holder and

briefly actuate the instant heat button

on the digital timer within 5 seconds

(display back lighting is illuminated)

- After 10 seconds briefly actuate the in-

stant heat button (display back lighting

is extinguished)

- Changeover is terminated

Telestart T91 / T100 HTM

Scope of delivery

Scope of delivery for T91

1 T91 transmitter

23Vbattery

3 Mounting bracket

4 T91/T100 HTM receiver

5 ESVT adapter

6Aerial

Scope of delivery for T100 HTM

1 T100 HTM transmitter

26Vbattery

3 Mounting bracket

4 T91/T100 HTM receiver

5 ESVT adapter

6Aerial

7 Temperature sensor

D network telephone kit (option)

1 Duplexer GSM/Telestart

2 HF-adapter cable (190 mm)

Telestart T91 / T100 HTM

Installation

The installation of the Telestart T91/T100

HTM may only be performed by an author-

ised Webasto dealer.

Installation of Telestart receiver

Caution:

The Telestart receiver must be installed in the

interior of the vehicle!

The preferred installation position is with the

plug-in connectors pointing downward, with

a maximum permissible deviation from the

perpendicular of <45° in either direction.

- Define the installation location of the

receiver in the interior of the vehicle

(preferably near the digital timer in the

case of retrofits)

- Secure the mounting bracket using

sheet-metal screws

- Fit receiver into the mounting bracket

Installation of aerial

Note:

Preferably, the aerial should be installed in

the interior of the vehicle, at the top in the

centre of the windshield or the rear window.

If installed in other locations, the range is

likely to be diminished.

For an optimal reception, a distance of

20 +/- 5 mm from the windshield edge is to

be maintained (see Fig.).

Depending on the installation location of the

aerial, the cable is routed either under the ve-

hicle roof trim and then to the right or left to

the strut or directly downward under the in-

strument panel.

Note:

If there is insufficient space available, the aer-

ial may be installed up to 150 mm off-centre.

- Clean windshield using grease-dissolv-

ing cleaner (e.g. methylated spirits)

- Peel off protective film from aerial and

fix aerial into place

Note:

Do not shorten aerial cable nor bend it sharply.

Smallest winding diameter is 50 mm.

- Route aerial cable to the receiver and

connect it to the receiver

Receiver

Mounting bracket

max. 300

max. 25

Additional installation location

Receiver

Aerial

Telestart T91 / T100 HTM

Installation of D network tele-

phone kit (option)

Connect duplexer GSM/Telestart into the ex-

isting D network aerial feeder line.

- Connect existing D network aerial

feeder line to the input of the GSM du-

plexer

- Connect adapter line (length:190 mm)

to the Telestart output of the GSM du-

plexer and to the Telestart receiver

- Connect the telephone line to the tele-

phone output of the GSM duplexer

Installation of ESVT adapter

(using example of Thermo Top C)

Pinning in cables on ESVT adapter: see

- Appendice 1 for analogue control

- Appendice 3 for W-bus control

- Route 4-pin connector of digital timer

of heater wiring harness into vehicle in-

terior

- Connect ESVT adapter to 4-pin con-

nector of digital timer

- Connect ESVT adapter to Telestart re-

ceiver

- Connect ESVT adapter to temperature

sensor (only with Telestart T100 HTM)

Receiver

Adapter

GSM duplexer

line

ESVT adapter

Connector of

Digital timer

Receiver

Temperature

sensor

(only with

T100 HTM)

Telestart T91 / T100 HTM

Telestart T91/T100 HTM retrofit

In conjunction with existing or new digital timer to be installed

Note:

Do not pull at the cables!

- Disconnect 4-pole connector from

digital timer

Pinning in cables on ESVT adapter: see

- Appendice 1 for analogue control

- Appendice 3 for W-bus control

- Connect ESVT adapter to 4-pin con-

nector of digital timer

- Connect ESVT adapter to Telestart re-

ceiver

- Connect ESVT adapter to temperature

sensor (only with T100 HTM)

- Connect ESVT adapter to digital timer

25A

15A 1A

123

Connector of

Digital timer

123

ESVT adapter

Connector of

Digital timer

Receiver

Digital timer

Temperature

sensor

(only with

T100 HTM)

Telestart T91 / T100 HTM

In conjunction with push-

button

Pinning in cables on ESVT adapter: see

- Appendice 2 for analogue control

- Appendice 4 for W-bus control

- Connect ESVT adapter to 4-pin con-

nector of digital timer

- Connect ESVT adapter to Telestart re-

ceiver

- Connect ESVT adapter to temperature

sensor (only with Telestart T100 HTM)

- Drill hole (16 mm dia.) in location

agreed upon with customer.

- Install pushbutton switch

Note:

When inserting the contacts into the recep-

tacle housing of the pushbutton switch, en-

sure that the colour coding matches that of

the ESVT adapter.

- Insert contacts into receptacle housing

of the pushbutton switch

- Connect the ESVT adapter to the con-

nector on the pushbutton switch.

Caution:

The default setting of the signal input must

be changed from digital timer to pushbutton

switch. See page 16.

Telestart T80 with digital

timer installed

- Remove Telestart T80 receiver

- Install Telestart T91/T100 HTM receiver

as described in installation instructions

Note:

The bracket of the T80 can be used to install

the T91/T100 HTM receiver.

- Remove Y-adapter and replace

with ESVT adapter

Pinning in cables on ESVT adapter: see

- Appendice 1 for analogue control

- Appendice 3 for W-bus control

Temperature

sensor

(only with

T100 HTM)

Digital timer

connector

Pushbutton

Switch

ESVT adapter

Receiver

Otros manuales para Telestart T91

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Electrónica del automóvil de otras marcas

GoldCruise

GoldCruise GC90Ci Manual de usuario

DRG

DRG LC 120 Manual de usuario

Blue Ox

Blue Ox BX8848 Manual de usuario

Dometic

Dometic MAGICWATCH MWE890K Manual de usuario

Perfect Power

Perfect Power SMT8-T5 Manual de usuario

Honeywell

Honeywell Thor VM3A Manual de usuario

Waeco

Waeco MagicWatch MWE250 Manual de usuario

Rydeen

Rydeen BKM091 Manual de usuario

Skoda

Skoda 5E0 054 630 Manual de usuario

VDO

VDO SENDER UNIT 2159-0 Manual de usuario

iDataLink

iDataLink maestro Rr Manual de usuario

Audiovox

Audiovox PRO-PDA15 Manual de usuario

Movon

Movon MDAS-3LFFHD Manual de usuario

Pioneer

Pioneer Comfort adapter CA-D-PI.150 Manual de usuario

Dietz

Dietz 1110 Manual de usuario

Crux

Crux RVCFD-79 Manual de usuario

Nonda

Nonda ZUS Manual de usuario

iDataLink

iDataLink Maestro Manual de usuario