Waterworks EEBT01 Hoja de instrucciones

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 4 | UPDATED ON 4.29.2021

STYLE No. EEBT01

Emile 67” x 27” x 27-1/2” Freestanding Oval

Cast Iron Bathtub

INSTALLATION GUIDELINES

IMPORTANT:

Immediately after receiving the BATHTUB and removal of packing,

you MUST inspect the unit for freight damage. Any claims for damage,

whether apparent or hidden, must be made to the carrier immediately

in order for them to assume all associated costs. Should inspection

reveal any defect in the finish, do not install the BATHTUB. Damage or

defect to the finish claimed after the BATHTUB is installed is excluded

from the warranty. The warranty DOES NOT cover labor or materials

to remove or re-install the BATHTUB.

To ensure this product is installed properly, you must read and follow

these guidelines.

The owner/user of this product must keep this information for future

reference.

CAUTION: This product is extremely heavy and adequate floor support

is required. Ensure the product is properly supported by the base.

This product must be installed by a professional licensed contractor.

Be sure your installation conforms to all federal, state, and local codes.

Inspect this product to assure it is the correct model and you have

all parts required for proper installation. Take all the necessary

precautions to ensure this product is protected during installation and

do NOT install this product if it has been damaged.

All final connections are made below the finished floor. Accessibility

below the finished floor is required.

The use of certain plumber’s putty may stain stone or tile surfaces.

WARNING: The following basic safety precautions should always be

followed when using your BATHTUB.

●Caution should always be exercised when entering or leaving the

BATHTUB.

●DANGER: To reduce the risk of injury, do NOT permit children

or persons with a disability to use the BATHTUB without close

supervision.

●Keep all electrical appliances such as radios and hairdryers a safe

distance from the BATHTUB.

●Do NOT use the BATHTUB when sleepy or drowsy, under

the influence of alcohol or prescription medications or when

overheated.

If further assistance is required, please contact Product Support at

1-800-927-2120 Monday through Friday, 8am – 6pm EST.

TECHNICAL DETAILS:

DETAIL SPECIFICATION

ADJUSTABLE LEVELERS/FEET YES

DRAIN HOLE DIAMETER 2-1/16” [53mm]

OVERFLOW HOLE DIAMETER 2-1/16” [53mm]

SINGLE OR DOUBLE ENDED DOUBLE ENDED

WATER CAPACTIY 57 gal [215 liters]

WEIGHT DRY 437 lbs. [198 kg]

FILLED 912 lbs. [414 kg]

REQUIRED PLUMBING DETAILS:

Universal Drain Plug Waste and Overflow Drain

STYLE No. UNWO76

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 4 | UPDATED ON 4.29.2021

STYLE No. EEBT01

Emile 67” x 27” x 27-1/2” Freestanding Oval

Cast Iron Bathtub

INSTALLATION GUIDELINES

1. Dry-fit the DRAIN FLANGE and SHOE to the

BATHTUB using the DRAIN GASKET provided.

2. Dry-fit the OVERFLOW SHOE to the BATHTUB

using the OVERFLOW GASKET provided.

NOTE: The UNWO76 is provided with 1 flat GASKET

and 1 wedge GASKET. Use the appropriate GASKET

to ensure the OVERFLOW SHOE is plumb.

3. Hold the TEE up to the DRAIN and OVERFLOW

PIPES then mark and cut the PIPES to the

appropriate lengths.

NOTE: Ensure the PIPES will be inserted deep

enough into the TEE before cutting.

4. Connect the OVERFLOW to the DRAIN using the

TEE making sure the OVERFLOW PIPE is plumb

and there are no gaps between the OVERFLOW

GASKET and the BATHTUB.

5. If rough-in has not been completed, determine

the placement of the BATHTUB and mark the

floor where the TAILPIECE will pass through then

drill a hole through the floor to accommodate the

TAILPIECE.

NOTE: A 3” diameter ESCUTCHEON is provided

with the UNWO76 to conceal the hole in the floor.

6. Rough-in 1-1/2” diameter piping and ensure all

piping and fittings are well supported to eliminate

the possibility of shifting.

DRAIN SHOE RUBBER

GASKET

BATHTUB

DRAIN

FLANGE

* DRY-FIT

OVERFLOW

SHOE

RUBBER

GASKET

OVERFLOW

COVER

SCREW

* DRY-FIT

TEE

CUT MARK

[OVERFLOW PIPE]

CUT MARK

[DRAIN PIPE]

TEE

OVERFLOW

PIPE

[PLUMB]

* DRY-FIT

[FULL SEAL - NO GAPS]

FLOOR

BATHTUB

[MARK DRAIN LOCATION]

* POSITION BATHTUB

1-1/2" PIPE

[NOT SUPPLIED] TRAP ADAPTER

[NOT SUPPLIED]

DRAIN HOLE

* ROUGH-IN

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 4 | UPDATED ON 4.29.2021

STYLE No. EEBT01

Emile 67” x 27” x 27-1/2” Freestanding Oval

Cast Iron Bathtub

INSTALLATION GUIDELINES

9. Slide a COMPRESSION NUT and RING onto the

DRAIN PIPE then connect the TEE to the PIPE.

7. Apply adequate non-staining plumber’s putty or

silicone to the DRAIN FLANGE then thread and

securely tighten the FLANGE into the DRAIN

SHOE.

8. Slide a COMPRESSION NUT and RING onto the

OVERFLOW PIPE then insert the PIPE into the TEE.

10. Using the appropriate GASKET, thread and securely

tighten the COVER SCREW into the OVERFLOW

SHOE.

11. Slide a COMPRESSION RING, COMPRESSION NUT

and the ESCUTCHEON onto the TAILPIECE then

apply pipe thread sealant to the TAILPIECE and

thread it into the TEE.

12. Position the BATHTUB so the TAILPIECE passes

through the hole in FLOOR and ensure the

BATHTUB sits level.

NOTE: The BATHTUB includes adjustable levelers.

DRAIN SHOE

RUBBER

GASKET

BATHTUB

DRAIN

FLANGE †

† APPLY PLUMBER'S

PUTTY OR SILICONE

OVERFLOW PIPE

COMPRESSION NUT

COMPRESSION RING

TEE

DRAIN PIPE

COMPRESSION NUT

COMPRESSION RING

TEE

OVERFLOW

SHOE

OVERFLOW

GASKET

OVERFLOW

COVER

SCREW

TEE

ESCUTCHEON

COMPRE-

SSION

NUT

COMPRESSION

RING

TAILPIECE

[THREAD

SEALANT]

FLOOR

BATHTUB

[ENSURE TUB

SITS LEVEL]

DRAIN HOLE

TAILPIECE

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 4 OF 4 | UPDATED ON 4.29.2021

STYLE No. EEBT01

Emile 67” x 27” x 27-1/2” Freestanding Oval

Cast Iron Bathtub

INSTALLATION GUIDELINES

13. Cut the TAILPIECE as needed then make final drain

connections and tighten the COMPRESSIONS

NUTS.

14. Plug the DRAIN and fill the BATHTUB until water

enters the overflow hole.

15. Drain the BATHTUB and inspect all connections for

leaks.

16. Slide the ESCUTCHEON down the OVERFLOW

PIPE until it contacts the floor then cover the

BATHTUB surface with a liner or other protective

material (not supplied) until construction is

complete.

[MAKE FINAL DRAIN

CONNECTIONS]

COMPRESSION

NUT [x3]

SPOUT *

[SOLD SEPARATELY]

* TURN ON WATER

PLUG PLUG

[CHECK ALL CONNECTIONS

FOR LEAKS]

PROTECTIVE

MATERIAL

[NOT PROVIDED]

ESCUTCHEON

Otros manuales de Bañera de Waterworks

Waterworks

Waterworks CLWP 50 Instrucciones de montaje

Manuales populares de Bañera de otras marcas

Agua

Agua BARTOLI-66 Manual de usuario

PAA

PAA PRELUDE Manual de usuario

BETTE

BETTE SILHOUETTE Manual de usuario

Kohler

Kohler K-820-GC Guía de inicio rápido

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Manual de usuario

Oliveri

Oliveri Naples Manual de usuario

Lyons

Lyons Elite ETLxx663219 Series Manual de usuario

Woodbridge

Woodbridge BJ500 Instrucciones de montaje

Whirlpool

Whirlpool Ariel ARL-702 Manual de usuario

TEIKO

TEIKO EXCELLENT DUO Manual de usuario

American Standard

American Standard Colony 5-1/2' x 32" Manual de usuario

American Standard

American Standard 3052OD.X0X Guía de inicio rápido

Kohler

Kohler K-1111-H2 Guía de inicio rápido

agape

agape MARSIGLIA AVAS1075 Manual de usuario

Kohler

Kohler K-1151 Instrucciones de montaje

Kohler

Kohler K-1158 Guía de inicio rápido

Kohler

Kohler K-1244 Instrucciones de montaje

Kallista

Kallista P50045-G5 Instrucciones de montaje