Walrus Audio Eons Manual de usuario

For Eons, man has thought the sound of thunder to be

from the heavens above, echoing boastfully over us as

we stay safe from its greatness. However, legend tells of

a stoic and indomitable beast residing in the highest

mountains seen and heard only by the most brash of

travelers. With gnarled and twisted horns, this creature

emits a sound thicker than Earth’s crust to command

attention and warn all who stand in his way. This is Eons.

VOLUME

The “Vol” knob sets the overall output

volume of the pedal. The “Voltage” and

“Gain” controls are very interactive with

the overall output volume of the pedal,

so there is plenty of volume on tap to

compensate.

VO LTAG E

POWER STUFF

The “Voltage” knob allows you to adjust the circuit’s

operating voltage. At its minimum, the main fuzz

section of the circuit will operate at around 3

volts, resulting in a “dying battery” sound. At its

maximum, the main fuzz section of the circuit will

operate at around 18 volts, resulting in a more open

and less compressed sound with added bass.

As you cut the voltage, the pedal will begin to

produce a starved sound and have a brighter

frequency response. As you approach noon

on the “Voltage” control, the pedal will begin

to have a gating effect. Lower voltages will also

drastically reduce the output volume of the

pedal. This knob behaves slightly differently

across all the different modes.

Got questions or need a repair? Email help@walrusaudio.com to talk

with a real live human about your Walrus gear!

This product comes with a limited lifetime warranty.

Click Here for more info.

9 volt DC, Center Neg.

100mA min*

*The use of an isolated power supply is

recommended for powering all Walrus Audio Pedals.

Daisy chain power supplies are not recommended.

GAIN

The “Gain” knob sets the

amount of gain applied to

your guitar signal passing

through the fuzz circuit. This

parameter is also highly interactive

with the “Voltage” knob. Pushing more

gain through the pedal at lower voltage settings

will result in grittier and dirtier sounds. Lower gain

settings at lower voltages will result in very starved

sounds. It can even cause the signal to cut out

completely at lower extremes, so adjust to taste!

BA S S

TREBLE

The “Bass” knob allows you to cut or boost low

frequencies after the fuzz circuit. This can be

helpful for tightening up the low end or

increasing the low frequency emphasis. Starting

at noon, turn down to remove bass and turn up

to add bass.

The “Treble” knob allows you to increase

clarity in the high frequency region or tame

them depending on your ampliﬁer and rig.

Like the bass control, you may ﬁnd that

at higher gains you will want to add more

treble, and at lower gains you may

want to roll the treble back. Starting

at noon, turn down to cut out

highs and turn up to allow

more highs.

MODE SWITCH

The “Mode” switch is a ﬁve-position rotary

switch. Each position offers a different

combination of frequency response and clipping

style employed by the pedal. You can think of

each position as a different “ﬂavor” of the pedal.

Each position is described in more detail below.

MODE SWITCH CONTINUED

I. Silicon soft clipping traditional fuzz that’s well rounded with a

huge sound; compressed and smooth.

II. Silicon clipping with an added bass boost that increases the low

end at the beginning of the circuit; compressed and crunchy.

III. Germanium soft clipping with a feel of “what if

a distortion and fuzz had a kid?”; crunchy

and dynamic.

I V. LED clipping diodes with a slight high-end

cut; dynamically dark.

V. Hard clipping silicon transistors combined with

LED and Silicon soft clipping diodes. The rowdiest

of the modes with tons of gain: compressed, loud,

and angry.

Note: Since the Mode switch is changing the internal gain and

clipping style, the other controls will behave slightly differently as

well. There is an internal gain change to help even out the output

level difference between the different clipping modes, but you may

still need to use the volume knob to adjust the overall output up or

down depending on which mode is selected. The Voltage knob also

heavily interacts with the volume and gain of the pedal, so you may

need to compensate by adjusting the “Gain“ or “Volume” knobs as

well to achieve your desired sound.

Tabla de contenidos

Otros manuales de Pedal de música de Walrus Audio

Walrus Audio

Walrus Audio LUMINARY V2 Manual de usuario

Walrus Audio

Walrus Audio CANVAS STEREO Manual de usuario

Walrus Audio

Walrus Audio MAKO M1 Manual de usuario

Walrus Audio

Walrus Audio MONUMENT Manual de usuario

Walrus Audio

Walrus Audio VANGUARD Manual de usuario

Walrus Audio

Walrus Audio Iron Horse V3 Manual de usuario

Walrus Audio

Walrus Audio ERAS Manual de usuario

Walrus Audio

Walrus Audio 385 Overdrive MKII Manual de usuario

Walrus Audio

Walrus Audio Mako Series Manual de usuario

Walrus Audio

Walrus Audio Bellwether Manual de usuario

Walrus Audio

Walrus Audio ARP-87 Manual de usuario

Walrus Audio

Walrus Audio AGES Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario