Wali PTT008 Manual de usuario
INSTALLATION MANUAL
PTT008
Monitor Stand Riser
D
20kg/44lbs
RATED
1-844-SATTLER (18447288537)
www.walielectric.com
Attach the Nut E to the hole on Board C as the image shown.
Caution: Please make sure the arrow on Nut E is pointing upright towards the edge of Board C as the image shown.
Place Support Stand B on a flat surface, insert the Bolt D to the center hole on Support Stand B and tighten
with a screwdriver. (Screwdriver not included)
Caution: Please make sure the Bolt D is vertically straight at an 90° angle to the surface of Support Stand B as
the image shown.
Insert the Wood Dowel Pin F to the side hole on Support Stand B .
Supplied Parts List
2
Step 1
Step 2
Board
A (x1)
Support Stand
B (x2)
Bolt
D (x6)
Board
C (x1)
Nut
E (x6)
Wood Dowel Pin
F (x4)
Cellphone Holder
H (x1)
Sticker
I (x6)
Anti-skid Pad
G (x4)
C
C
C
B
F
D
E
E
E
B
B
B
B
B
D
F
D
D
F
Caution: Frequently assembling and disassembling may cause damage to the wood board.
Support Stand surface
DB
90° Angle
Bolt
Insert Board C to the Bolt D and Wood Dowel Pin F on Support Stand B and tighten the Nut E clockwise
to fasten for stability. (Screwdriver not included)
3
E
E
Step 3
B
B
F
B
F
D
D
C
C
C
Board surface
Place Board A on a flat surface with bottom upward, insert the Bolt D to the hole on Board A and tighten
with a screwdriver. (Screwdriver not included)
Caution: Please make sure the Bolt D is vertically straight at an 90° angle to the surface of Board A as the image shown.
Attach the Nut E to the hole on Support Stand B as the image shown.
Caution: Please make sure the arrow on the nut is pointing upright towards the hole on the Support Stand B as the image
shown.
4
D
D
D
DA
A
A
A
A
Step 4
Step 5
B
B
B
C
E
E
90° Angle
Bolt
Tighten the Nut E clockwise to fasten for stability. (Screwdriver not included)
Insert the assembled support stand to the Bolt D on Board A .
5
Step 7
Step 6
A
A
D
D
E
E
Tear off the Anti-Skid Pad G and sticker I , attach it to the designated position as the image shown.
Insert the Cellphone Holder H to the designated position on Board A .
Notice: The Cellphone Holder is removable. Push it from the back of the Board A to remove it if necessary.
Optional Step
6
Step 8
A
A
A
H
H
I
I
G
G
Otros manuales de Rack y soporte de Wali
Wali
Wali PTT007-B Manual de usuario
Wali
Wali MF003S Manual de usuario
Wali
Wali M002-W Manual de usuario
Wali
Wali M002XLS Manual de usuario
Wali
Wali CS202 Manual de usuario
Wali
Wali MF002 Manual de usuario
Wali
Wali GSDM003-P Manual de usuario
Wali
Wali SBR201 Manual de usuario
Wali
Wali GSMP001W Manual de usuario
Wali
Wali GSMP001 Manual de usuario
Wali
Wali M002 Manual de usuario
Wali
Wali GSDM003S Manual de usuario
Wali
Wali TVDVD-01 Manual de usuario
Wali
Wali M001XLLP Manual de usuario
Wali
Wali M002LM Manual de usuario
Wali
Wali GSMP002 Manual de usuario
Wali
Wali CS201 Manual de usuario
Wali
Wali MF002-W Manual de usuario
Wali
Wali TVS001 Manual de usuario
Wali
Wali WMH002-B Manual de usuario
