Wacker Neuson BS 50-2 Manual de usuario

5000184075 08 0612

5000184075

Operator’s Manual

Vibratory Rammer

BS 50-2

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

BS 50-2 Foreword

wc_tx001354gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

;

Machine

documentation

From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

Keep a copy of the Operator’s Manual with the machine at all times.

Use the separate Parts Book supplied with the machine to order replacement

parts.

Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Machine Item Number Revision Machine Item Number Revision

BS 50-2 0009384 Rev 121,

Rev 200+

BS 50-2 0620048 Rev 115,

Rev 200+

BS 50-2 0009410 Rev 121,

Rev 200+

BS 50-2 0620609 Rev 100+

BS 50-2 0009411 Rev 121,

Rev 200+

BS 50-2 0620610 Rev 100+

BS 50-2 0009413 Rev 121,

Rev 200+

BS 50-2 0620733 Rev 100+

BS 50-2 0620025 Rev 115,

Rev 200+

—— —

Foreword BS 50-2

4 wc_tx001354gb.fm

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

Serious injury hazards to the operator and persons in the work area

Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2012-CE-BS50-2-2i_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS 50-2, BS 50-2i

Vibratory Rammer

To compact soil

0009410, 0009411, 0009413, 0620025, 0620048,

0009412, 0009414, 0009416, 0009473, 0620026,

5200003696

1,7 kW

106 dB(A)

108 dB(A)

Conformity Assessment Procedure

According to ANNEX VIII

Notified Body

Lloyds Register Quality Assurance Limited (Notified Body No 0088)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2004/26/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 28.06.12

William Lahner

Managing Director

Paul Sina

Manager, Product Engineering

Todd Lutz

Director of Business Development

Table of Contents

BS 50-2

wc_bo5000184075_08TOC.fm 7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Safety Guidelines for Lifting the Machine ........................................... 12

1.5 Service Safety .................................................................................... 13

1.6 Operator Safety while Using Internal Combustion Engines ............... 15

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 21

3.1 Lifting the Rammer ............................................................................. 21

3.2 Transporting the Rammer .................................................................. 22

4 Operation 23

4.1 Preparing the Machine for First Use ................................................... 23

4.2 Recommended Fuel ........................................................................... 24

4.3 Refueling the Machine ........................................................................ 25

4.4 Position of the Operator ..................................................................... 26

4.5 Before Starting ................................................................................... 26

4.6 Starting, Operating, and Stopping the Machine ................................. 27

4.7 Emergency Shutdown Procedure ....................................................... 29

4.8 Optional Equipment ............................................................................ 29

5 Maintenance 30

5.1 Maintaining the Emission Control System .......................................... 30

5.2 Periodic Maintenance Schedule ......................................................... 31

5.3 Servicing the Air Cleaner .................................................................... 32

5.4 Checking the Fuel Lines and Fittings ................................................. 34

5.5 Maintaining the Shoe Hardware ......................................................... 34

5.6 Inspecting the Machine ...................................................................... 35

Table of Contents BS 50-2

wc_bo5000184075_08TOC.fm

5.7 Cleaning the Engine Cooling Fins .......................................................36

5.8 Cleaning and Checking the Spark Plug ...............................................37

5.9 Checking and Changing the Ramming System Oil .............................38

5.10 Adjusting the Idle Speed .....................................................................40

5.11 Inspecting and Cleaning the Fuel Filter ...............................................41

5.12 Long-Term Storage .............................................................................42

5.13 Machine Disposal / Decommissioning .................................................43

6 Basic Troubleshooting 44

7 Technical Data 45

7.1 Rammer ...............................................................................................45

7.2 Sound Measurements .........................................................................46

7.3 Vibration Measurements .....................................................................46

7.4 Dimensions ..........................................................................................47

8 Emission Control Systems Information and Warranty 49

8.1 Emission Control System Background Information .............................49

8.2 Limited Defect Warranty for Wacker Neuson Emission Control

Systems ...............................................................................................50

wc_si000688gb.fm 9

BS 50-2 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

fObey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

fTo avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

fTo avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

fTo avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000688gb.fm

Safety Information BS 50-2

1.2 Machine Description and Intended Use

This machine is a vibratory rammer. The Wacker Neuson Rammer consists of a

gasoline or diesel engine, a clutch, a fuel tank, a spring-loaded ramming system, a

ramming shoe, and a handle. The engine transmits power through the ramming

system and ramming shoe, generating percussive impact force to compact soil.

The operator guides and controls the machine from behind using the handle.

This machine is intended to be used for compacting cohesive, mixed, and granular

soils in confined areas.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

Using the machine as a ladder, support, or work surface

Using the machine to carry or transport passengers or equipment

Using the machine as a hammer or for other demolition work

Attaching the machine to any other machine

Operating the machine outside of factory specifications

Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

Heat, noise, exhaust, and carbon monoxide from the engine

Fire hazards from improper refueling techniques

Fuel and its fumes

Personal injury from improper lifting techniques or operating techniques

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

Otros manuales para BS 50-2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Wacker Neuson

Wacker Neuson

Wacker Neuson DPU 4045H Manual de usuario

Wacker Neuson

Wacker Neuson VP 2050 Manual de usuario

Wacker Neuson

Wacker Neuson WP Series Manual de usuario

Wacker Neuson

Wacker Neuson BS 50 Instrucciones de funcionamiento

Wacker Neuson

Wacker Neuson VP1030A-CE Manual de usuario

Wacker Neuson

Wacker Neuson BS 50-4s Manual de usuario

Wacker Neuson

Wacker Neuson DPU 6555He Manual de usuario

Wacker Neuson

Wacker Neuson ARFU 36/6/120 Manual de usuario

Wacker Neuson

Wacker Neuson AP1840 Series Manual de usuario

Wacker Neuson

Wacker Neuson VP2050A US Manual de usuario

Wacker Neuson

Wacker Neuson BPS1030A Manual de usuario

Wacker Neuson

Wacker Neuson BS 65-V Manual de usuario

Wacker Neuson

Wacker Neuson BS 60-2i Manual de usuario

Wacker Neuson

Wacker Neuson EH 9 BL/230 Manual de usuario

Wacker Neuson

Wacker Neuson BS 50 Instrucciones de funcionamiento

Wacker Neuson

Wacker Neuson DPU 130Le Manual de usuario

Wacker Neuson

Wacker Neuson AR 36 Series Manual de usuario

Wacker Neuson

Wacker Neuson DPU 4545 Manual de usuario

Wacker Neuson

Wacker Neuson BPU 3050A Manual de usuario

Wacker Neuson

Wacker Neuson DPU 6555 Manual de usuario

Wacker Neuson

Wacker Neuson WP 1550A Manual de usuario

Wacker Neuson

Wacker Neuson BS 60-2i Manual de usuario

Wacker Neuson

Wacker Neuson DPU 2950 Manual de usuario

Wacker Neuson

Wacker Neuson WP Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual